CS Paper Radar

Nonlinear Dynamic Modeling and Receding-Horizon NMPC of an Electric Unicycle on a Tensioned Cable

Yousef Sweiti, Jasem Tamimi

eess.SY ·submitted 2026-09-21 08:59 UTC · v1
published

Abstract

Traversing flexible slender structures involves strong bidirectional coupling between vehicle motion and structural vibration caused by a moving contact point. This paper presents a nonlinear modeling-and-control framework for an electric unicycle traversing a tensioned flexible cable. The cable is modeled using a tension-dominated finite-element formulation retaining vertical and lateral transverse dynamics, and is coupled to the unicycle roll and pitch dynamics through moving-contact kinematics. A modal truncation yields a control-oriented reduced-order model that preserves the nonlinear vehicle--cable coupling. Based on this model, a constrained nonlinear model predictive controller is formulated to regulate traversal, balance, actuator limits, and cable-span constraints. To reduce the computational burden associated with moving-contact interpolation, a frozen spatial contact-point interpolation strategy is introduced for the NMPC prediction model. Numerical studies under nominal, disturbed, constrained, and model-mismatch scenarios show accurate traversal, roll and pitch stabilization, attenuation of cable vibrations, and constraint-consistent closed-loop behavior. The frozen-interpolation formulation reduces and regularizes NMPC computation times relative to the non-frozen formulation, supporting its use as a computationally tractable approach for finite-element-based moving-contact vehicle--structure interaction systems.

Journal ref
Journal of the Franklin Institute, 363(15), 109057 (2026)
DOI
10.1016/j.jfranklin.2026.109057

Closest papers

Nearest neighbours by meaning across the whole index.

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.62
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Task-Space Motion-Force Nonlinear Model Predictive Control for Precise and Compliant Control under Uncertainties

cs.RO ·2026-10-12 ·Quang-Nam Nguyen, Ludovic Righetti
hot direction similarity 0.55
Abstract

In Nonlinear Model Predictive Control (NMPC), the control law is implicitly determined by the solution of an Optimal Control Problem (OCP). Consequently, OCP design is often tailored to specific platforms and tasks, demanding extensive expert knowledge and tuning effort. To address this, we propose a unified NMPC framework that directly plans and controls the robot joints subject to task-space motion and force requirements and is capable of seamlessly generalizing across multiple robotic platforms and diverse tasks. Furthermore, optimization-based methods often treat interactions as rigid contacts, making the torque solution sensitive to the modeling errors of the robot dynamics and the environment. We study the intrinsic task-space impedance of our proposed controller, its partial contraction for differential stability and differential passivity under unmodeled interactions. As a result, our framework enables closing the force-feedback loop in the high-level planning layer to achieve precise motion-force tracking performance, addressing the long-standing challenge of force-feedback NMPC. Finally, we validate our framework on physical hardware, demonstrating hybrid motion-force control on a redundant manipulator and compliant locomotion on a quadruped, while preserving core NMPC advantages such as hard constraint satisfaction, optimal redundancy exploitation, and real-time planning under unforeseen interactions.

0.42

Stabilizing Low-Stiffness Soft Robots at Unstable Equilibria: A Model-Based Optimal Control Approach

eess.SY ·2026-10-12 ·Nikhil Nair, Daniele Caradonna, Anup Teejo Mathew, Federico Renda, Cosimo Della Santina +1 more
similarity 0.54
Abstract · 7 pages, 6 figures

Continuum soft robots are highly nonlinear and underactuated systems, which makes stabilizing them around unstable equilibrium points difficult. This challenge becomes even greater in low stiffness regimes, where gravitational forces dominate elastic forces. In this letter, we explore whether optimal control can address these challenges using a computa- tionally efficient method suitable for real time use. We propose a nonlinear model predictive control (NMPC) approach based on Differential Dynamic Programming (DDP), combined with an accurate reduced order Variable Strain model with analytical derivatives. This results in an efficient control framework for addressing the stabilization problem. Tested on a soft inverted pendulum and other hybrid soft rigid systems, the method outperforms traditional controllers, stabilizes more challenging configurations, and operates reliably at real time speeds (50 150 Hz), demonstrating both effectiveness and practical feasibility in experimental settings.

0.26

Aerial Non-Stop Trajectories Preserving the Equilibrium of Loads Suspended by Variable-Length Cables

eess.SY ·2026-09-11 ·Antonio Franchi, Alberto Landi, Chiara Gabellieri
similarity 0.54
Abstract

This work studies equilibrium-preserving non-stop trajectories of aerial carriers connected to rigid loads by variable-length cables. Internal-force motions vary the cable directions without changing the load wrench, while cable-length actuation shapes the radial realization of the carrier trajectories. We derive an explicit cable-length law for realizing prescribed carrier-position profiles along a fixed direction, with constant altitude as a relevant specialization. Under this constraint, a carrier stops exactly when its cable direction stops changing. This characterization reveals a distinction between unrestricted and level motion: variable cable lengths enable bounded non-stop motion with two carriers, whereas periodic level non-stop motion is obstructed for two carriers and constructively achieved for three or more under explicit geometric and feasibility conditions. Numerical simulations illustrate the constant-altitude construction.

0.25

DR-MPC: Fast and Feasible Dynamics-Relaxed Model-Predictive Control for Legged Locomotion

cs.RO eess.SY ·2026-09-17 ·Run Wang, Alapati Tuerxun, Shuo Liu, Wei Xiao, Ján Drgoňa +2 more
code/data similarity 0.54
Abstract · 8 pages, 5 figures, submitted to RA-L

This paper presents dynamics-relaxed model predictive control (DR-MPC), a novel MPC formulation for legged locomotion, and a tailored interior-point method (IPM) solver. The formulation combines online optimization feasibility by construction with a contact-aware input parameterization. DR-MPC moves the dynamics equality and affine input constraints into quadratic penalties and retains only nonempty box constraints. The resulting box-constrained quadratic program (QP) has a block-arrow Hessian that enables the state and affine-output directions to be eliminated through a Schur complement. The solver factors only the reduced control system after swing-force elimination and contact-aligned move blocking. For the evaluated implementations using the same DR-MPC formulation, our method achieves median end-to-end MPC speedups of $16.0\times$ over HPIPM and $4.4\times$ over OSQP, with comparable locomotion performance in simulation. DR-MPC achieves a median onboard MPC end-to-end time of $4.4$ ms and is validated on a Unitree Go1 quadruped. Open-source code will be made available after publication.

0.27

Adapting Rigid-Body Dynamics Derivatives for Constraint Embedding Closed-Chain Models

cs.RO ·2026-09-17 ·Daniel J. Volpi, Patrick M. Wensing
top venue similarity 0.53
Abstract · 8 pages, 6 figures

This paper extends an existing algorithm for the first-order derivatives of rigid-body dynamics to the case of closed-chain kinematic systems modeled using constraint embed- ding. Many standard dynamics algorithms apply to both open- chain and constraint-embedded models, but existing efficient derivative methods assume joint velocity effects are locally config- uration invariant. We remove this assumption and derive adapted algorithms that extend dynamics derivatives to more general joint types, including those arising in constraint-embedded closed- chain models. Our results compare conventional pin-joint robot models with more complete actuation models that capture local closed chains. We show that the additional terms introduced by these generalizations have low computational impact when mod- eling actuation kinematics alone, but can incur higher cost when additional rigid bodies, such as motor rotors, are included in the actuation chain, or when considering non-local loops. Overall, these results enable more accurate dynamics computations for constraint-embedded actuation submechanisms to be adopted in model-predictive control and differentiable simulation.

0.60

Dynamics Modeling of a Multi-UAV Slung Load System Using a Discrete-Link Cable Approach

cs.RO ·2026-10-05 ·Harvey Merton, Ian W. Hunter
top venuecode/data similarity 0.53
Abstract · Presented at ICRA 2026 as an accepted paper

A common assumption to simplify the problem of controlling a multi-UAV slung load system (MUSLS) is that the flexible cables can be modeled as massless rigid rods. In this work, we propose an alternative Euler-Newton derived dynamical model which uses a series of rigid links to model the flexible cables. The model is specifically designed to allow efficient simulation using Featherstone's articulated body algorithm. We perform real-world validation of this model on gentle, aggressive, and tension-engagement maneuvers and run a parameter sweep to determine the number of links, joint damping, and joint friction to achieve the greatest model fidelity. The model closely matches real-world flight data with mean load translation errors below 132 mm (5.5% of the cable length) and orientation errors below 11.4 degrees. We make the real-world flight data publicly available for the development of future cable models.

0.54

Online iLQR-MPC with Whole-Body Control for Robust Humanoid Locomotion

cs.RO ·2026-11-03 ·Xiang Li, Linlin Ou, Ruihan Wu, Xinyi Yu
similarity 0.52
Abstract

Humanoid locomotion requires deciding where to step and how to distribute contact forces. However, a disturbance can invalidate the nominal plan, requiring coordinated revision under constraints that switch with every footfall. To solve this online, the proposed approach employs the single-rigid-body model, which retains attitude dynamics and the full contact wrench. An iterative linear-quadratic-regulator MPC (iLQR-MPC) then jointly optimizes contact forces and footstep locations in a single receding-horizon problem, without a separate step planner. Specifically, contact and motion constraints are incorporated into the backward pass through augmented-Lagrangian and relaxed-barrier penalties. A whole-body controller subsequently maps the plan to joint torques at 500 Hz while preserving contact feasibility. The model-based formulation makes disturbance responses interpretable through explicit costs and constraints, and requires no platform-specific policy training. In MuJoCo simulations, the iLQR-MPC replans at 100 Hz (mean solve time 8.9 ms); the Unitree G1 sustains steady-state walking and recovers from impulsive 245 N forward and 175 N lateral pushes.

0.18