CS Paper Radar

Payload Swing Estimation and Damping Without Payload Parameters for Multirotor UAVs

K. Taki, K. Umemoto

eess.SY cs.RO ·submitted 2026-08-19 07:19 UTC · v1

Abstract

Cable-suspended payload transport by multirotor UAVs is flexible but generates periodic swing disturbance that degrades tracking and risks instability. Existing anti-swing methods require additional sensors or precise identification of cable length and payload mass, limiting field deployment. We propose a swing-estimation and damping method using only the onboard IMU and throttle command, requiring no payload parameters. An extended Kalman filter extracts the periodic disturbance with the unknown pendulum frequency as an estimated state, and an active damping controller adds a correction angle to the attitude loop to dissipate pendulum energy. Flight experiments confirm robust damping across a tested range of cable-length and mass variations.

Closest papers

Nearest neighbours by meaning across the whole index.

Dynamics Modeling of a Multi-UAV Slung Load System Using a Discrete-Link Cable Approach

cs.RO ·2026-10-05 ·Harvey Merton, Ian W. Hunter
top venuecode/data similarity 0.66
Abstract · Presented at ICRA 2026 as an accepted paper

A common assumption to simplify the problem of controlling a multi-UAV slung load system (MUSLS) is that the flexible cables can be modeled as massless rigid rods. In this work, we propose an alternative Euler-Newton derived dynamical model which uses a series of rigid links to model the flexible cables. The model is specifically designed to allow efficient simulation using Featherstone's articulated body algorithm. We perform real-world validation of this model on gentle, aggressive, and tension-engagement maneuvers and run a parameter sweep to determine the number of links, joint damping, and joint friction to achieve the greatest model fidelity. The model closely matches real-world flight data with mean load translation errors below 132 mm (5.5% of the cable length) and orientation errors below 11.4 degrees. We make the real-world flight data publicly available for the development of future cable models.

0.54

Compact Force Sensor for Dual-UAV Cable-Suspended Payload Transport with Tension-Aware Outer-Loop Control

cs.RO ·2026-09-25 ·Andrea Delbene, Giorgio Cannata, Giorgio Carlini, Filippo Sante, Marco Baglietto
top venue similarity 0.64
Abstract · Preprint version for IEEE Robotics and Automation Letters, link to article: https://ieeexplore.ieee.org/document/11743837

Cooperative payload transportation using multiple Unmanned Aerial Vehicles (UAVs) poses challenges in stability, coordination, and robustness, especially under external disturbances and unmodeled dynamics. This work proposes a dual-UAV payload transportation framework supported by a compact, custom-designed force sensor measuring the interaction force at the UAV cable anchor point. The sensor design and mathematical model are presented, and its performance is characterized through static and dynamic tests evaluating linearity, hysteresis, repeatability, and crossload. The control architecture follows a cascade structure: fast inner loops handle vehicle stabilization, while outer loops are designed to compensate for the measured forces. The approach is validated through simulations and indoor experiments under position uncertainty. Payload-drop and constrained-space tests assess the proposed sensing and control architecture against literature-based distributed references, showing improved stabilization, coordination, and disturbance rejection. A video of the experiments is available at: https://youtu.be/rIw9-fvV8Qw.

0.47

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

cs.RO eess.SY ·2026-09-17 ·Ali Jokar, Amin Talaeizadeh, Aria Alasty
similarity 0.60
Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

0.13

Passive Stiffness Shaping in Cable-Suspended Aerial Manipulation via Movable Compliant Anchors

cs.RO cs.MAeess.SY ·2026-09-30 ·Antonio Franchi, Amr Afifi
similarity 0.57
Abstract

Cable-suspended aerial manipulation offers a lightweight architecture for cooperative transportation and physical interaction, yet the passive mechanical response perceived at the load remains insufficiently understood and systematically exploited. This work interprets aerial vehicles as movable compliant anchors and develops a gravity-aware quasi-static theory for predicting and shaping the passive Cartesian stiffness of a suspended load. The formulation applies to an arbitrary number of aerial vehicles connected to a point load by taut, straight, inextensible cables. At a selected gravity-loaded equilibrium, aerial-anchor compliance and transverse cable geometric compliance combine in series within each leg, while the leg stiffnesses act in parallel on the load. For isotropic aerial-anchor behavior, each leg is exactly equivalent to a virtual unilateral elastic cable, revealing an axial--transverse stiffness decomposition governed by the equilibrium tension. These results define a nonlinear map from commanded-anchor configuration to passive load stiffness, whose differential enables local constraint-preserving shaping through anchor repositioning. A dynamic rigid-body validation framework with nonlinear vehicle control, elastic-damped tendons, and environmental contact is defined to assess when and to what extent the derived stiffness remains predictive beyond the assumptions of the analytical model.

0.14

Cooperative Aerial Transportation of a Payload with a Sliding Cable Attachment

cs.RO cs.MA ·2026-10-09 ·Sebastian Tilaguy Lezama, Diego S D'Antonio
similarity 0.57
Abstract

This paper presents a dual-quadrotor hook- suspended transport system for cooperative aerial manipulation of a payload that is not rigidly attached to a fixed point along the cable. Two quadrotors are connected by a single inextensible cable that passes through a frictionless hook mounted on the payload, allowing the cable to slide between its two segments. This introduces a cable-distribution variable that couples the quadrotor motion, cable geometry, and payload dynamics. A feasible reference-generation framework is formulated using the desired payload pose, cable distribution, and system shape while satisfying the cable-length constraint and elliptical workspace. The quadrotors track the geometrically generated trajectories while maintaining positive cable tension and respecting actuator limits. The payload pose is estimated from the system geometry, and its measured position is used only to validate the desired trajectory. The approach is evaluated through experimental demonstrations.

0.33

Tether-Inertial Localization for Planetary Drones

cs.RO ·2026-08-10 ·Dielof van Loon, Anton Bredenbeck, Lennart Puck, Martin Azkarate, Salua Hamaza
top venue similarity 0.57
Abstract

Recent developments in planetary exploration have shown the potential of Unmanned Aerial Vehicles (UAVs), such as the Ingenuity helicopter that provided valuable mapping data. However, limited payload capabilities constrain the flight times and compute available for localization, which restrict their applicability. By providing a tethered connection, issues such as battery and computational constraints are offloaded to the base rover. At the same time, the cable can be exploited for non-drifting localization. This work presents a novel Tether-Inertial Localization approach that uses tether length and angle measurements to estimate the UAV position relative to its base. The method combines a computationally efficient analytical catenary model with a Gaussian Process (GP) residual error compensation. This accounts for systematic sensor inaccuracies and model limitations. Experimental validation across circular, triangular, and figure-eight trajectories with tether lengths up to 4.5 m and a total flight time of 37 minutes demonstrates the effectiveness of the proposed approach. Using only tether-based position estimates for feedback, the analytical catenary model achieves an average RMSE of 7.4 cm, which is further reduced to 5.2 cm through GP-based residual compensation, one order of magnitude better than the state-of-the-art. These results establish Tether-Inertial Localization as a practical alternative to vision- and GNSS-based localization for Tethered Unmanned Aerial Vehicles (TUAVs).

0.34

AFD-CAMLs: Agile Force-Distribution-Aware Planning and Control for Cable-Suspended Aerial Multi-Lifting Systems

cs.RO ·2026-10-01 ·Antreas Kourris, Sihao Sun
similarity 0.56
Abstract · 9 pages, 11 figures

Multiple UAVs can cooperatively transport heavy payloads while controlling their position and orientation. Trajectory-based methods offer high agility while satisfying system constraints, but can produce uneven force distributions when the tension-to-wrench allocation is redundant or ill-conditioned, particularly under geometric mismatch and low-level tracking errors. We propose a hybrid planning-and-control framework to address this problem. A global planner generates payload trajectories and cable-force references by exploring the allocation null space under a prescribed internal-force setting. These references augment the cost of a centralized local planner, promoting feasible force distributions while generating trajectories for all UAVs. An admittance filter then compares the planned forces with onboard cable-tension estimates and adjusts the kinematic references to improve force tracking in degenerate or near-degenerate configurations. Simulations and experiments involving four to ten UAVs demonstrate more balanced tension distributions during both hovering and demanding agile maneuvers, without compromising agility or payload-tracking performance.

0.27

Aerial Non-Stop Trajectories Preserving the Equilibrium of Loads Suspended by Variable-Length Cables

eess.SY ·2026-09-11 ·Antonio Franchi, Alberto Landi, Chiara Gabellieri
similarity 0.54
Abstract

This work studies equilibrium-preserving non-stop trajectories of aerial carriers connected to rigid loads by variable-length cables. Internal-force motions vary the cable directions without changing the load wrench, while cable-length actuation shapes the radial realization of the carrier trajectories. We derive an explicit cable-length law for realizing prescribed carrier-position profiles along a fixed direction, with constant altitude as a relevant specialization. Under this constraint, a carrier stops exactly when its cable direction stops changing. This characterization reveals a distinction between unrestricted and level motion: variable cable lengths enable bounded non-stop motion with two carriers, whereas periodic level non-stop motion is obstructed for two carriers and constructively achieved for three or more under explicit geometric and feasibility conditions. Numerical simulations illustrate the constant-altitude construction.

0.25