CS Paper Radar

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

Ali Jokar, Amin Talaeizadeh, Aria Alasty

cs.RO eess.SY ·submitted 2026-09-17 21:20 UTC · v1

Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

Closest papers

Nearest neighbours by meaning across the whole index.

Observer-Based Robust Control for an Aerial Manipulator System under Unknown External Disturbances

eess.SY ·2026-09-07 ·Mayank Pandey, Sneha Gajbhiye
similarity 0.66
Abstract

This paper addresses the mathematical modeling and control of an aerial manipulator system comprising a quadrotor as the uncrewed aerial vehicle and a robotic arm as the manipulator. The dynamic model is established by identifying the overall center-of-mass velocity and the system's orientation as constraints, yielding a simplified, two-decoupled subsystems: a locked (overall translation) subsystem and a shape-space (actuation or overall rotation) subsystem, both subjected to external disturbances. Since the system is mechanically coupled, a critical challenge arises where constant bounded disturbances in the first subsystem manifest as time-varying, state-dependent disturbances in the second subsystem. Given that the quadrotor is inherently unstable, the movement of the robotic manipulator (RM) during flight can further jeopardize the stability of the entire QRM system if these disturbances and coupling effects are not effectively managed. To address this, we present a continuous nonlinear disturbance observer-based feedback control law, which enables the independent control of each subsystem while systematically eliminating cross-coupling effects. The efficacy of the proposed controller is validated through multiple simulations emulating practical operating conditions, thereby substantiating its real-world applicability and highlighting the core contributions of this work.

0.11

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.63
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.51

Design and Control of a Multimodal Legged-Aerial Robot Through Separate Control Contraction Metrics

cs.RO eess.SY ·2026-10-19 ·Kaushik Venkatesh Krishnamurthy, Eric Sihite, Alireza Ramezani, Morteza Gharib
published similarity 0.62
Abstract · Presented at 2026 IEEE International Conference on Intelligent Robots and Systems, Pittsburgh PA

The integration of dynamic legged locomotion and aerial mobility offers versatility that is deterred by challenges in payload distribution, actuation, and the contrasting requirements of both domains. In this paper, we present the design and operation of a multimodal quadrupedal aerial-legged robot. The presence of legged aerial systems also allows for thruster-assisted legged locomotion, which we make possible with a unified control framework using Control Contraction Metrics (CCM). We search for separate domain-specific contraction metrics for walking and flight independently offline and unify them using an online energy-based Control Lyapunov Function Quadratic Program (CLF QP). This enables optimal, cross-domain control allocation, which we show using simulations. We also show experimental results that validate the mechanical viability of our hardware and the paradigm of thruster-assisted trotting. The stability of said experiments motivates the deployment of the control framework for multimodal operations.

0.20

Bio-inspired Thrust-Assisted Trotting on a legged-Aerial Robot via Real-Time QP-MPC

cs.RO ·2026-10-19 ·Shreyansh Pitroda, Eric Sihite, Alireza Ramezani, Morteza Gharib
published similarity 0.61
Abstract · To be published in IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

This paper presents the hardware implementation of a quadratic program-based controller on Harpy: thruster-assisted bipedal robot to perform thruster-assisted trotting. This is inspired by wing-assisted locomotion observed in birds such as the chukar partridge, which employ thrust vectoring to manipulate the ground reaction force. The proposed controller formulates the thruster-assisted spring-loaded inverted pendulum dynamics as a condensed QP-based model predictive control problem, enabling simultaneous regulation of ground contact force and active thrust vectoring at 500 Hz. A decoupled control architecture is used, where the robot's sagittal dynamics are controlled using QP-MPC while the frontal dynamics is regulated using a cascade orientation stabilization controller. Two experiments were conducted with different forward reference velocities of 0 m/s and 0.1 m/s. While the instantaneous velocity oscillates, the mean velocities can track their respective reference. Additionally, joint tracking error remains within 1 deg while tracking the desired leg length given by the leg trajectory controller and desired swing trajectory given by Raibert's heuristic. The QP-MPC problem is consistently solved with 0.18ms, which is well within the 2ms computation budget while satisfying the GRF friction cone constraint.

0.40

Optimized Modular Design and Development of a Tilt-Rotor Bicopter Drone

cs.RO ·2026-08-31 ·Saideep Verma, Nimisha Tatapudi, Akshay Arjun, Danwada Sharanya Sukka, Abhishek Sarkar +1 more
similarity 0.61
Abstract · 7 pages, conference, Index terms -Tilt-Rotor Bicopter Drone, Optimal Modular Design, Static Analysis, Dynamic Flight Analysis

Hybrid systems like tilt-rotor bicopter drones combine the beneficial characteristics of both fixed-wing and rotary-wing technology, enabling long endurance and VTOL capability. However, such drones also require an optimum design to ensure both static and dynamic stability. The modular design of a traditional bicopter is developed in this paper based on extensive analysis and in-depth structural and aerodynamic simulations. The structural analysis has been performed to ensure that the aircraft's structure withstands the stresses encountered during different flight modes. Controlling the relative positions of the Center of Gravity (CG) and Neutral Point (NP) is an essential aspect of the design, ensuring stability during hover and positive stability during forward flight. The thrust and power analyses have been conducted to assess the flight performance and endurance. After analysis, the drone has been developed, and flight tests with a basic flight controller were conducted to validate the performance metrics obtained in the simulation.

0.24

Tilt-Rotor Quadcopter with Learned Residual Control and Mode-Dependent State Estimation

cs.RO ·2026-10-22 ·Ninad Joshi, Prabhat Kumar
similarity 0.60
Abstract · 5 figures

Tilt-rotor quadcopters redirect thrust for translation without banking, but complicate modeling, state estimation, and disturbance rejection. This paper presents a simulation-based flight stack for a \SI{2.00}{\kilo\gram} tilt-rotor quadcopter. The system uses a six-degree-of-freedom nonlinear model with first-order motor dynamics and two-axis rotor tilt, parameterized using a 3D CAD model. A cascaded PD controller commands forward and lateral tilt angles. A 14-state EKF fuses sensor data across hover, early-transition, and transition modes using a hysteretic (Schmitt-trigger) classifier to prevent covariance discontinuities. Because the proportional position loop leaves a steady-state offset under constant wind, a small bounded neural residual is added on top of the unmodified PD controller. It is trained by behavioral cloning from a teacher with privileged access to the true wind, while the deployed network never observes wind. In simulation, the EKF achieves a post-settling position root mean square error (RMSE) of \SI{0.226}{\metre} (horizontal) and \SI{0.03}{\metre} (vertical) and an attitude RMSE below \SI{0.8}{\degree}, and it estimates a wind velocity of $(\num{2.0}, \num{-1.2})\,\unit{\metre\per\second}$ to within \SI{0.15}{\metre\per\second} per axis. The residual reduces steady-state station-keeping error under wind by approximately \SI{49}{\percent}, from \SI{0.117}{\metre} to \SI{0.060}{\metre} at \SI{1.5}{\metre\per\second} and from \SI{0.319}{\metre} to \SI{0.162}{\metre} at an out-of-distribution \SI{3.9}{\metre\per\second}. The framework provides a basis for hardware-in-the-loop and flight-test studies.

0.29

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
highly cited similarity 0.60
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.35

Payload Swing Estimation and Damping Without Payload Parameters for Multirotor UAVs

eess.SY cs.RO ·2026-08-19 ·K. Taki, K. Umemoto
similarity 0.60
Abstract

Cable-suspended payload transport by multirotor UAVs is flexible but generates periodic swing disturbance that degrades tracking and risks instability. Existing anti-swing methods require additional sensors or precise identification of cable length and payload mass, limiting field deployment. We propose a swing-estimation and damping method using only the onboard IMU and throttle command, requiring no payload parameters. An extended Kalman filter extracts the periodic disturbance with the unknown pendulum frequency as an estimated state, and an active damping controller adds a correction angle to the attitude loop to dissipate pendulum energy. Flight experiments confirm robust damping across a tested range of cable-length and mass variations.

0.21