CS Paper Radar

Optimized Modular Design and Development of a Tilt-Rotor Bicopter Drone

Saideep Verma, Nimisha Tatapudi, Akshay Arjun, Danwada Sharanya Sukka, Abhishek Sarkar, Joyjit Mukherjee

cs.RO ·submitted 2026-08-31 04:10 UTC · v1

Abstract

Hybrid systems like tilt-rotor bicopter drones combine the beneficial characteristics of both fixed-wing and rotary-wing technology, enabling long endurance and VTOL capability. However, such drones also require an optimum design to ensure both static and dynamic stability. The modular design of a traditional bicopter is developed in this paper based on extensive analysis and in-depth structural and aerodynamic simulations. The structural analysis has been performed to ensure that the aircraft's structure withstands the stresses encountered during different flight modes. Controlling the relative positions of the Center of Gravity (CG) and Neutral Point (NP) is an essential aspect of the design, ensuring stability during hover and positive stability during forward flight. The thrust and power analyses have been conducted to assess the flight performance and endurance. After analysis, the drone has been developed, and flight tests with a basic flight controller were conducted to validate the performance metrics obtained in the simulation.

Comment
7 pages, conference, Index terms -Tilt-Rotor Bicopter Drone, Optimal Modular Design, Static Analysis, Dynamic Flight Analysis

Closest papers

Nearest neighbours by meaning across the whole index.

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

cs.RO eess.SY ·2026-09-17 ·Ali Jokar, Amin Talaeizadeh, Aria Alasty
similarity 0.61
Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

0.13

Mass Scaling Laws for Energy-Optimal Horizontal Multirotor Flight

cs.RO eess.SY ·2026-11-03 ·Ayush Patnaik, Nicolas Michel, Leonard Baursfeld, Davide Scaramuzza, Xinfan Lin
top venue similarity 0.58
Abstract · Accepted to IEEE Robotics and Automation Letters, October 2026

Multicopters are a type of aerial robot seeing extensive real-world applications but with range and endurance as critical bottlenecks. Optimization of its energy efficiency through energy-aware flight planning (e.g. cruise speed-scheduling) has hence been an important topic. The mass of the multicopter is an important factor to consider, as it has a significant impact on efficiency, and many common applications are subject to frequent mass variation due to payload change. This work derives closed-form scaling relationships between the energy-optimal steady horizontal flight behavior of a multicopter and its vehicle mass, and validates them experimentally on two multirotor platforms. Specifically, for mass-only variation, i.e., when payload changes the vehicle mass while the airframe geometry, aerodynamic characteristics, and rotor configuration remain unchanged, we show through a combination of numerical simulation, theoretical derivation, and experimental validation that (1) the energy-optimal velocity is proportional to the square root of vehicle mass; (2) the energy-optimal pitch angle is constant with respect to mass; and (3) the optimal energy per meter is proportional to mass. The analysis shows that these three relationships arise from a common mass-similarity property of the steady-state flight and rotor-aerodynamic equations. Furthermore, the obtained scaling relationships enable simple yet effective cruise-speed planning to optimize energy efficiency and extend the range and endurance of the multicopter.

0.45

From Model to Prototype: Design and Motor-Flap Propulsion Control of a Twin-Wing Metamorphic UAV

cs.RO ·2026-10-06 ·Anja Bosak, Dorian Erić, Ana Milas, Stjepan Bogdan
similarity 0.57
Abstract · 8 pages, 12 figures

This paper presents the design and control strategy for MetaMorpher, a metamorphic Unmanned Aerial Vehicle (UAV), capable of both spinning-wing hover and fixed flying-wing cruise flight. Since control of the cruise configuration is comparatively well established in the literature, this paper focuses on control of the MetaMorpher in hover mode, building on the flight dynamics model and conceptual design validated in previous work. The control algorithm is implemented using one of two phase-synchronized strategies: motor propulsion, which pulses motor thrust in synchrony with the vehicle's rotation, or flap propulsion, a novel strategy that pulses the deflection of the wing-mounted elevons. We evaluate both strategies in simulation through different flight experiments. Simulation results confirm the mathematical model and show stable reference tracking, demonstrating flap propulsion as a lightweight, decoupled alternative for hover control. Experimental testing validated the vertical-dynamics propulsion model against the physical prototype, demonstrating very good steady-state agreement across different configurations.

0.22

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

cs.RO ·2026-08-24 ·Aniketh Parkala, Harikumar Kandath
published similarity 0.56
Abstract · 8 pages

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

0.33

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.54
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

Observer-Based Robust Control for an Aerial Manipulator System under Unknown External Disturbances

eess.SY ·2026-09-07 ·Mayank Pandey, Sneha Gajbhiye
similarity 0.53
Abstract

This paper addresses the mathematical modeling and control of an aerial manipulator system comprising a quadrotor as the uncrewed aerial vehicle and a robotic arm as the manipulator. The dynamic model is established by identifying the overall center-of-mass velocity and the system's orientation as constraints, yielding a simplified, two-decoupled subsystems: a locked (overall translation) subsystem and a shape-space (actuation or overall rotation) subsystem, both subjected to external disturbances. Since the system is mechanically coupled, a critical challenge arises where constant bounded disturbances in the first subsystem manifest as time-varying, state-dependent disturbances in the second subsystem. Given that the quadrotor is inherently unstable, the movement of the robotic manipulator (RM) during flight can further jeopardize the stability of the entire QRM system if these disturbances and coupling effects are not effectively managed. To address this, we present a continuous nonlinear disturbance observer-based feedback control law, which enables the independent control of each subsystem while systematically eliminating cross-coupling effects. The efficacy of the proposed controller is validated through multiple simulations emulating practical operating conditions, thereby substantiating its real-world applicability and highlighting the core contributions of this work.

0.11

Task-Driven Closed-Loop Design Optimization of Passively Morphing Quadrotors for Contact-Mediated Narrow Gap Traversal

cs.RO ·2026-11-06 ·Etor Arza, Luca Girardi, Gabriel Maquignaz, Javier Paez, Stefan Leutenegger +2 more
code/data similarity 0.53
Abstract · Video: https://youtu.be/xGkEtl6-vCA. Code: https://github.com/ntnu-arl/soft-quadrotor-optimization

Aerial robots operating in cluttered environments may encounter openings narrower than their nominal width. Existing passively morphing drones reduce their width upon traversal, but they typically involve human-made designs, which can struggle to find the right balance among folding ratio, flight efficiency, and control tracking performance. We introduce a closed-loop design method that jointly optimizes quadrotor geometry and the torque-deflection response of two passively folding arms driven by the success rate in simulation for contact-mediated gap traversal. An optimization algorithm samples candidate designs that are evaluated in a contact-based simulation of the traversal task, where the task success rate is used as a feedback signal to sample progressively better designs over time. The resulting prototype passively reduces its width from 31.3 to 14.1 cm and traverses a 15 cm wide opening at a 2 m/s reference speed. It also tolerates gap approach-angle errors of up to 30 degrees and folds through a 40 cm long confined passage. Compared to a rigid twin, the soft configuration adds only 2 mm of position RMSE and less than 1% electrical power during contact-free flight. These results show that task-driven closed-loop design optimization can produce passively morphing airframes that are compact under contact, tolerant to approach error, and effectively rigid during nominal flight.

0.28

Tilt-Rotor Quadcopter with Learned Residual Control and Mode-Dependent State Estimation

cs.RO ·2026-10-22 ·Ninad Joshi, Prabhat Kumar
similarity 0.53
Abstract · 5 figures

Tilt-rotor quadcopters redirect thrust for translation without banking, but complicate modeling, state estimation, and disturbance rejection. This paper presents a simulation-based flight stack for a \SI{2.00}{\kilo\gram} tilt-rotor quadcopter. The system uses a six-degree-of-freedom nonlinear model with first-order motor dynamics and two-axis rotor tilt, parameterized using a 3D CAD model. A cascaded PD controller commands forward and lateral tilt angles. A 14-state EKF fuses sensor data across hover, early-transition, and transition modes using a hysteretic (Schmitt-trigger) classifier to prevent covariance discontinuities. Because the proportional position loop leaves a steady-state offset under constant wind, a small bounded neural residual is added on top of the unmodified PD controller. It is trained by behavioral cloning from a teacher with privileged access to the true wind, while the deployed network never observes wind. In simulation, the EKF achieves a post-settling position root mean square error (RMSE) of \SI{0.226}{\metre} (horizontal) and \SI{0.03}{\metre} (vertical) and an attitude RMSE below \SI{0.8}{\degree}, and it estimates a wind velocity of $(\num{2.0}, \num{-1.2})\,\unit{\metre\per\second}$ to within \SI{0.15}{\metre\per\second} per axis. The residual reduces steady-state station-keeping error under wind by approximately \SI{49}{\percent}, from \SI{0.117}{\metre} to \SI{0.060}{\metre} at \SI{1.5}{\metre\per\second} and from \SI{0.319}{\metre} to \SI{0.162}{\metre} at an out-of-distribution \SI{3.9}{\metre\per\second}. The framework provides a basis for hardware-in-the-loop and flight-test studies.

0.29