CS Paper Radar

Task-Driven Closed-Loop Design Optimization of Passively Morphing Quadrotors for Contact-Mediated Narrow Gap Traversal

Etor Arza, Luca Girardi, Gabriel Maquignaz, Javier Paez, Stefan Leutenegger, Stefano Mintchev, Kostas Alexis

cs.RO ·submitted 2026-11-06 10:27 UTC · v2
code/data

Abstract

Aerial robots operating in cluttered environments may encounter openings narrower than their nominal width. Existing passively morphing drones reduce their width upon traversal, but they typically involve human-made designs, which can struggle to find the right balance among folding ratio, flight efficiency, and control tracking performance. We introduce a closed-loop design method that jointly optimizes quadrotor geometry and the torque-deflection response of two passively folding arms driven by the success rate in simulation for contact-mediated gap traversal. An optimization algorithm samples candidate designs that are evaluated in a contact-based simulation of the traversal task, where the task success rate is used as a feedback signal to sample progressively better designs over time. The resulting prototype passively reduces its width from 31.3 to 14.1 cm and traverses a 15 cm wide opening at a 2 m/s reference speed. It also tolerates gap approach-angle errors of up to 30 degrees and folds through a 40 cm long confined passage. Compared to a rigid twin, the soft configuration adds only 2 mm of position RMSE and less than 1% electrical power during contact-free flight. These results show that task-driven closed-loop design optimization can produce passively morphing airframes that are compact under contact, tolerant to approach error, and effectively rigid during nominal flight.

Comment
Video: https://youtu.be/xGkEtl6-vCA. Code: https://github.com/ntnu-arl/soft-quadrotor-optimization

Closest papers

Nearest neighbours by meaning across the whole index.

Aerial Layouting: Design and Control of a Compliant and Actuated End-Effector for Precise In-flight Marking on Ceilings

cs.RO ·2026-08-11 ·Christian Lanegger, Marco Ruggia, Marco Tognon, Lionel Ott, Roland Siegwart
publishedhighly cited similarity 0.67
Abstract · C. Lanegger and M. Ruggia contributed equally. Accepted to Robotics: Science and Systems (RSS) 2022

Aerial robots have demonstrated impressive feats of precise control, such as dynamic flight through openings or highly complex choreographies. Despite the accuracy needed for these tasks, there are problems that require levels of precision that are challenging to achieve today. One such problem is aerial interaction. Advances in aerial robot design and control have made such contact-based tasks possible and opened up research into challenging real-world tasks, including contact-based inspection. However, while centimetre accuracy is sufficient and achievable for inspection tasks, the positioning accuracy needed for other problems, such as layouting on construction sites or general push-and-slide tasks, is millimetres. To achieve such a high precision, we propose a new aerial system composed of an aerial vehicle equipped with a novel "smart" end-effector leveraging a stability-optimized Gough-Stewart mechanism. We present its design process and features incorporating the principles of compliance, multiple contact points, actuation, and self-containment. In experiments, we verify that the design choices made for our novel end-effector are necessary to obtain the desired positioning precision. Furthermore, we demonstrate that we can reliably mark lines on ceilings with millimetre accuracy without the need for precise modeling or sophisticated control of the aerial robot.

0.61

Residual Wrench Certification and Margin-Aware Control Synthesis for Aerial Physical Interaction

cs.RO eess.SY ·2026-09-30 ·Abhimanyu Khadga, Abhinav Sinha, Shashi Ranjan Kumar
similarity 0.64
Abstract

We develop a task-relative framework for certifying residual wrench authority after hover and contact loading in multirotors with bounded actuators. Using convex geometry, we derive signed margins for prescribed convex reserves, including Euclidean balls and weighted ellipsoids. We obtain computable reserve certificates from actuator-interiority bounds to support slack-maximizing allocation. To preserve the required reserve, we propose command projection onto a tightened feasible set. We then connect the available reserve to structured gain synthesis and certify a local tracking region that respects actuator limits. Within this region, we establish nominal exponential convergence and robust ultimate boundedness. For the prescribed task and morphology family, we show that the optimized octarotor attains a larger margin than the optimized hexarotor at equal total thrust. We evaluate the proposed framework in closed-loop simulations of sustained rigid-wall contact using a fixed-geometry octarotor and a variable-tilt quadrotor with matched installed thrust. The quadrotor's local certificate admits a higher normalized push limit for the prescribed task family. In tests beyond the realizability boundaries, we observe the predicted loss of authority through rotor-thrust limits for the octarotor and tilt-servo limits for the quadrotor.

0.17

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
highly cited similarity 0.63
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.36

AeRSoM: An Aerial Rigid-Soft Integrated Manipulator for Contact-Rich Manipulation

cs.RO ·2026-09-22 ·Jiacheng Liang, Hang Zhong, Yaonan Wang, Ge Chen, Zhixing Zhang +3 more
similarity 0.63
Abstract

Contact-rich aerial manipulation remains fundamentally challenging because interaction forces are directly transmitted to the aerial platform, often leading to instability and degraded task performance. While compliant manipulators can mitigate these effects, existing aerial manipulation systems typically struggle to reconcile interaction compliance with manipulation precision. To this end, this article presents an aerial rigid-soft integrated manipulator (AeRSoM) robot that realizes embodied compliance for aerial manipulation. The proposed system integrates a fully actuated aerial platform, a rigid-soft manipulator, and variable-stiffness regulation to simultaneously achieve stable flight, compliant interaction, and precise manipulation. By distributing compliance throughout the manipulation system, the proposed design leverages distributed embodied compliance to passively absorb contact disturbances while preserving sufficient stiffness for task execution. To fully exploit the mechanical design, a composite control framework is developed for precise end-effector trajectory tracking in the presence of uncertainties and external disturbances. Extensive real-world experiments are conducted in representative contact-rich aerial manipulation tasks, including dynamic transmission-line grasping, physical interaction with a wind turbine blade, peg-in-hole, and screwing operations. The results demonstrate that the proposed rigid-soft integration significantly improves interaction robustness and task adaptability while maintaining manipulation accuracy, highlighting that embodied compliance provides a promising design paradigm for enhancing the safety, robustness, and versatility of aerial manipulation.

0.20

Contact as a Decision Variable: Capability-Tradeoff Contact Selection for Legged Loco-Manipulation

cs.RO ·2026-09-24 ·Al Jaber Mahmud, Shuai Li, Xuan Wang
similarity 0.63
Abstract · 9 pages, 6 figures

In this paper, we study the joint selection of an environmental support contact and a whole-body configuration for a prescribed loco-manipulation task. A contact may provide greater physical support while restricting the motion required for the task. We formulate this problem through three capability measures: residual wrench, end-effector reach, and base mobility available after satisfying the task requirements, and we balance them against contact acquisition cost. Evaluating these capabilities for every candidate requires repeated whole-body optimizations. To reduce this computational cost, we propose Capability-Tradeoff Contact Selection (CTCS). CTCS screens candidates for contact and task feasibility, groups similar candidates within each surface, and predicts their capabilities from exact anchor evaluations using local sensitivity analysis. It checks these predictions through selective exact evaluations, ranks candidates by capability, and evaluates a shortlist exactly for final selection. We evaluate CTCS in simulations and hardware experiments using a Unitree Go2 quadruped with an AgileX NERO arm across $392$ task conditions with nine available support surfaces. Results show that CTCS outperforms ground-only and fixed-contact support, as it can select support surfaces that provide favorable capability trade-offs for the task. Compared with evaluating every candidate exactly, CTCS achieves approximately $3\times$ speedup while closely matching the resulting mean objective value.

0.56

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.62
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

AFD-CAMLs: Agile Force-Distribution-Aware Planning and Control for Cable-Suspended Aerial Multi-Lifting Systems

cs.RO ·2026-10-01 ·Antreas Kourris, Sihao Sun
similarity 0.61
Abstract · 9 pages, 11 figures

Multiple UAVs can cooperatively transport heavy payloads while controlling their position and orientation. Trajectory-based methods offer high agility while satisfying system constraints, but can produce uneven force distributions when the tension-to-wrench allocation is redundant or ill-conditioned, particularly under geometric mismatch and low-level tracking errors. We propose a hybrid planning-and-control framework to address this problem. A global planner generates payload trajectories and cable-force references by exploring the allocation null space under a prescribed internal-force setting. These references augment the cost of a centralized local planner, promoting feasible force distributions while generating trajectories for all UAVs. An admittance filter then compares the planned forces with onboard cable-tension estimates and adjusts the kinematic references to improve force tracking in degenerate or near-degenerate configurations. Simulations and experiments involving four to ten UAVs demonstrate more balanced tension distributions during both hovering and demanding agile maneuvers, without compromising agility or payload-tracking performance.

0.27

Vision-Guided Morphing Quadcopter for Multi-Geometry Payload Transport through Narrow Passages

cs.RO ·2026-08-22 ·Aashish Sahu, Shriram Hari, R. Prasanth Kumar
similarity 0.61
Abstract

Aerial payload transport using multirotor unmanned aerial vehicles is challenging because payload geometry, contact interaction, grasp stability, flight control, and narrow-passage traversal are strongly coupled during pickup and transport. Object-specific grippers often cannot adapt their footprint or grasp geometry when the payload shape or passage width changes. This paper presents a vision-guided morphing quadcopter for multi-geometry payload transport through narrow passages. The proposed platform uses four hybrid arm-leg structures that function as both landing supports and grasping members. A centrally placed actuator drives a tendon-based morphing mechanism, enabling all four arms to synchronously retract or expand for object grasping, footprint reduction, and post-transport release. Onboard vision estimates the payload geometry and passage width, while endpoint force feedback is used to confirm grasp contact during payload engagement. A phase-wise mission planner, PID-based flight stabilization, and morphology-adaptive grasp controller are implemented in a MuJoCo simulation environment. The framework is evaluated using box, cylindrical, and spherical payloads, representing flat-faced, rolling-curved, and fully curved contact conditions. Across the three cases, the simulated system completes the pickup-transport-release sequence with a maximum RMS position error of 0.31 m, a final drop-zone error below 0.18 m, a compact grasp footprint of 0.09-0.21 m2, and a footprint reduction of 75.0-89.7 percent. The results demonstrate that a single-actuator morphing quadcopter can adapt its grasp footprint for the transport of payloads with different geometries while reducing its overall footprint for narrow-passage traversal.

0.20