CS Paper Radar

Aerial Layouting: Design and Control of a Compliant and Actuated End-Effector for Precise In-flight Marking on Ceilings

Christian Lanegger, Marco Ruggia, Marco Tognon, Lionel Ott, Roland Siegwart

cs.RO ·submitted 2026-08-11 14:41 UTC · v1
publishedhighly cited

Abstract

Aerial robots have demonstrated impressive feats of precise control, such as dynamic flight through openings or highly complex choreographies. Despite the accuracy needed for these tasks, there are problems that require levels of precision that are challenging to achieve today. One such problem is aerial interaction. Advances in aerial robot design and control have made such contact-based tasks possible and opened up research into challenging real-world tasks, including contact-based inspection. However, while centimetre accuracy is sufficient and achievable for inspection tasks, the positioning accuracy needed for other problems, such as layouting on construction sites or general push-and-slide tasks, is millimetres. To achieve such a high precision, we propose a new aerial system composed of an aerial vehicle equipped with a novel "smart" end-effector leveraging a stability-optimized Gough-Stewart mechanism. We present its design process and features incorporating the principles of compliance, multiple contact points, actuation, and self-containment. In experiments, we verify that the design choices made for our novel end-effector are necessary to obtain the desired positioning precision. Furthermore, we demonstrate that we can reliably mark lines on ceilings with millimetre accuracy without the need for precise modeling or sophisticated control of the aerial robot.

Comment
C. Lanegger and M. Ruggia contributed equally. Accepted to Robotics: Science and Systems (RSS) 2022

Closest papers

Nearest neighbours by meaning across the whole index.

AeRSoM: An Aerial Rigid-Soft Integrated Manipulator for Contact-Rich Manipulation

cs.RO ·2026-09-22 ·Jiacheng Liang, Hang Zhong, Yaonan Wang, Ge Chen, Zhixing Zhang +3 more
similarity 0.73
Abstract

Contact-rich aerial manipulation remains fundamentally challenging because interaction forces are directly transmitted to the aerial platform, often leading to instability and degraded task performance. While compliant manipulators can mitigate these effects, existing aerial manipulation systems typically struggle to reconcile interaction compliance with manipulation precision. To this end, this article presents an aerial rigid-soft integrated manipulator (AeRSoM) robot that realizes embodied compliance for aerial manipulation. The proposed system integrates a fully actuated aerial platform, a rigid-soft manipulator, and variable-stiffness regulation to simultaneously achieve stable flight, compliant interaction, and precise manipulation. By distributing compliance throughout the manipulation system, the proposed design leverages distributed embodied compliance to passively absorb contact disturbances while preserving sufficient stiffness for task execution. To fully exploit the mechanical design, a composite control framework is developed for precise end-effector trajectory tracking in the presence of uncertainties and external disturbances. Extensive real-world experiments are conducted in representative contact-rich aerial manipulation tasks, including dynamic transmission-line grasping, physical interaction with a wind turbine blade, peg-in-hole, and screwing operations. The results demonstrate that the proposed rigid-soft integration significantly improves interaction robustness and task adaptability while maintaining manipulation accuracy, highlighting that embodied compliance provides a promising design paradigm for enhancing the safety, robustness, and versatility of aerial manipulation.

0.20

Robust Sliding Mode and Admittance Control of Underactuated Aerial Manipulators for Contact-Based Inspection

cs.RO ·2026-08-11 ·Tareq Aziz Alqutami, Yvan Petillot, Matthew W. Dunnigan, Mustafa Suphi Erden
published similarity 0.70
Abstract · 6 pages, 7 figures, submitted to 2026 IEEE Industrial Electronics and Applications Conference (IEACon)

Contact-based industrial inspection requires aerial platforms to maintain stable interaction while rejecting disturbances. Underactuated aerial manipulators present control challenges due to the dynamic coupling between vehicle attitude and force generation. This paper proposes a robust control framework for an underactuated hexarotor equipped with a 1-DoF manipulator to perform sustained contact inspection. The architecture integrates integral-augmented Sliding Mode Control (SMC) for trajectory tracking with an admittance control law for force regulation. The contact force is mapped to a feedforward attitude term, while the 1-DoF arm actively compensates for the tilt to maintain surface alignment. Software-in-the-loop simulations demonstrate that the SMC-based approach achieves superior tracking and coupling rejection compared to traditional PID. Furthermore, the interaction strategy achieved precise force regulation with an RMSE of 0.12N and was able to stably exert up to 20N force, confirming the system's efficacy for stable, reliable contact-based inspection.

0.26

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.67
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

Task-Driven Closed-Loop Design Optimization of Passively Morphing Quadrotors for Contact-Mediated Narrow Gap Traversal

cs.RO ·2026-11-06 ·Etor Arza, Luca Girardi, Gabriel Maquignaz, Javier Paez, Stefan Leutenegger +2 more
code/data similarity 0.67
Abstract · Video: https://youtu.be/xGkEtl6-vCA. Code: https://github.com/ntnu-arl/soft-quadrotor-optimization

Aerial robots operating in cluttered environments may encounter openings narrower than their nominal width. Existing passively morphing drones reduce their width upon traversal, but they typically involve human-made designs, which can struggle to find the right balance among folding ratio, flight efficiency, and control tracking performance. We introduce a closed-loop design method that jointly optimizes quadrotor geometry and the torque-deflection response of two passively folding arms driven by the success rate in simulation for contact-mediated gap traversal. An optimization algorithm samples candidate designs that are evaluated in a contact-based simulation of the traversal task, where the task success rate is used as a feedback signal to sample progressively better designs over time. The resulting prototype passively reduces its width from 31.3 to 14.1 cm and traverses a 15 cm wide opening at a 2 m/s reference speed. It also tolerates gap approach-angle errors of up to 30 degrees and folds through a 40 cm long confined passage. Compared to a rigid twin, the soft configuration adds only 2 mm of position RMSE and less than 1% electrical power during contact-free flight. These results show that task-driven closed-loop design optimization can produce passively morphing airframes that are compact under contact, tolerant to approach error, and effectively rigid during nominal flight.

0.28

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
similarity 0.66
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.35

DuctAM: A Duct-Assisted Quadrotor-Based Aerial Manipulator Enabling High-Force Push-and-Pull Interactions

cs.RO ·2026-09-14 ·Yi Wang, Rui Jin, Xinhang Xu, Haotian Jin, Ruiyang Liu +2 more
highly cited similarity 0.65
Abstract

Uncrewed Aerial Manipulators (UAMs) extend the capabilities of Uncrewed Aerial Vehicles (UAVs) from perception to physical interaction. Among various aerial interactions, push-and-pull operations are fundamental manipulation primitives that require sustained horizontal forces while maintaining stable flight. In this paper, we propose DuctAM, a compact aerial manipulation platform that enhances horizontal force capability for push-and-pull interactions using two ducted fans integrated along the quadrotor interaction axis. An attitude-force decoupled control scheme enables controllable horizontal forces without requiring large attitude changes. Extensive real-world experiments are conducted to validate the DuctAM. Figure-eight trajectory tracking experiments demonstrate stable flight and accurate motion control in both quad and duct modes. Force-measurement experiments quantify the decoupled longitudinal force capability of DuctAM. Finally, representative push-and-pull interaction tasks, including cart pushing, door closing, and drawer opening, verify the practical effectiveness of DuctAM. The results show that DuctAM achieves significantly improved horizontal interaction force capability while maintaining stable flight compared with conventional UAVs.

0.40

CAPTURER: A Dexterous Aerial Manipulator for Dynamic and Precise Grasping across Diverse Environments

cs.RO ·2026-10-29 ·Meng Wang, Jindou Jia, Sicheng Zhou, Zeshuai Chen, Kexin Guo +2 more
similarity 0.65
Abstract

As a representative form of embodied robotic interaction, aerial grasping requires close coordination between the aerial platform and manipulator. Most existing systems perform aerial grasping with static or slowly moving targets under fixed scenarios. Dynamic and precise grasping across different conditions introduces additional challenges, including target motion, localization drift, dynamic coupling, and external disturbances. In this work, we present CAPTURER, a dexterous aerial manipulator for centimeter-level grasping across diverse environments. To achieve the challenging goal, we first develop an onboard perception system for state estimation and target detection. Drift correction and global pose transformation are introduced to improve target localization during flight. A cooperative motion planner is proposed to coordinate the mobility of the aerial platform with the dexterity of the manipulator according to the relative target state. To maintain grasping accuracy under disturbances, we design a disturbance-rejection controller to compensate for dynamic coupling, model uncertainty, and external disturbances. The capability of CAPTURER is validated through indoor and outdoor experiments with both static and moving targets. The results demonstrate that CAPTURER achieves centimeter-level grasping accuracy for a marker pen measuring only 1.5 cm in diameter at flight speeds exceeding 1.5 m/s.

0.24

Residual Wrench Certification and Margin-Aware Control Synthesis for Aerial Physical Interaction

cs.RO eess.SY ·2026-09-30 ·Abhimanyu Khadga, Abhinav Sinha, Shashi Ranjan Kumar
similarity 0.64
Abstract

We develop a task-relative framework for certifying residual wrench authority after hover and contact loading in multirotors with bounded actuators. Using convex geometry, we derive signed margins for prescribed convex reserves, including Euclidean balls and weighted ellipsoids. We obtain computable reserve certificates from actuator-interiority bounds to support slack-maximizing allocation. To preserve the required reserve, we propose command projection onto a tightened feasible set. We then connect the available reserve to structured gain synthesis and certify a local tracking region that respects actuator limits. Within this region, we establish nominal exponential convergence and robust ultimate boundedness. For the prescribed task and morphology family, we show that the optimized octarotor attains a larger margin than the optimized hexarotor at equal total thrust. We evaluate the proposed framework in closed-loop simulations of sustained rigid-wall contact using a fixed-geometry octarotor and a variable-tilt quadrotor with matched installed thrust. The quadrotor's local certificate admits a higher normalized push limit for the prescribed task family. In tests beyond the realizability boundaries, we observe the predicted loss of authority through rotor-thrust limits for the octarotor and tilt-servo limits for the quadrotor.

0.17