CS Paper Radar

DuctAM: A Duct-Assisted Quadrotor-Based Aerial Manipulator Enabling High-Force Push-and-Pull Interactions

Yi Wang, Rui Jin, Xinhang Xu, Haotian Jin, Ruiyang Liu, Yizhuo Yang, Lihua Xie

cs.RO ·submitted 2026-09-14 16:54 UTC · v1
highly cited

Abstract

Uncrewed Aerial Manipulators (UAMs) extend the capabilities of Uncrewed Aerial Vehicles (UAVs) from perception to physical interaction. Among various aerial interactions, push-and-pull operations are fundamental manipulation primitives that require sustained horizontal forces while maintaining stable flight. In this paper, we propose DuctAM, a compact aerial manipulation platform that enhances horizontal force capability for push-and-pull interactions using two ducted fans integrated along the quadrotor interaction axis. An attitude-force decoupled control scheme enables controllable horizontal forces without requiring large attitude changes. Extensive real-world experiments are conducted to validate the DuctAM. Figure-eight trajectory tracking experiments demonstrate stable flight and accurate motion control in both quad and duct modes. Force-measurement experiments quantify the decoupled longitudinal force capability of DuctAM. Finally, representative push-and-pull interaction tasks, including cart pushing, door closing, and drawer opening, verify the practical effectiveness of DuctAM. The results show that DuctAM achieves significantly improved horizontal interaction force capability while maintaining stable flight compared with conventional UAVs.

Closest papers

Nearest neighbours by meaning across the whole index.

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.71
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

AeRSoM: An Aerial Rigid-Soft Integrated Manipulator for Contact-Rich Manipulation

cs.RO ·2026-09-22 ·Jiacheng Liang, Hang Zhong, Yaonan Wang, Ge Chen, Zhixing Zhang +3 more
similarity 0.71
Abstract

Contact-rich aerial manipulation remains fundamentally challenging because interaction forces are directly transmitted to the aerial platform, often leading to instability and degraded task performance. While compliant manipulators can mitigate these effects, existing aerial manipulation systems typically struggle to reconcile interaction compliance with manipulation precision. To this end, this article presents an aerial rigid-soft integrated manipulator (AeRSoM) robot that realizes embodied compliance for aerial manipulation. The proposed system integrates a fully actuated aerial platform, a rigid-soft manipulator, and variable-stiffness regulation to simultaneously achieve stable flight, compliant interaction, and precise manipulation. By distributing compliance throughout the manipulation system, the proposed design leverages distributed embodied compliance to passively absorb contact disturbances while preserving sufficient stiffness for task execution. To fully exploit the mechanical design, a composite control framework is developed for precise end-effector trajectory tracking in the presence of uncertainties and external disturbances. Extensive real-world experiments are conducted in representative contact-rich aerial manipulation tasks, including dynamic transmission-line grasping, physical interaction with a wind turbine blade, peg-in-hole, and screwing operations. The results demonstrate that the proposed rigid-soft integration significantly improves interaction robustness and task adaptability while maintaining manipulation accuracy, highlighting that embodied compliance provides a promising design paradigm for enhancing the safety, robustness, and versatility of aerial manipulation.

0.20

QuadHand: A Compact Quadrotor Aerial Manipulator with MRC-SDF-Based Whole-Body Motion Planning

cs.RO ·2026-09-28 ·Rui Jin, Ruiyang Liu, Xinhang Xu, Haotian Jin, Yi Wang +2 more
similarity 0.67
Abstract

Uncrewed aerial manipulators (UAMs) integrate robotic arms with aerial platforms for three-dimensional physical interaction. However, enlarging the workspace increases arm-induced disturbances, while existing geometric representations face a trade-off between geometric fidelity and computational efficiency in close-proximity interaction. This paper presents QuadHand, a compact quadrotor aerial manipulator with a 3-DoF arm, gripper, and battery-assisted passive CoG compensation module to reduce dominant arm-induced disturbances. We further propose MRC-SDF, a Multi-articulated Robot-Centric Signed Distance Field that preserves fine geometric detail with tractable computation, and a spatiotemporal whole-body trajectory optimization framework that jointly optimizes the quadrotor and manipulator for safe and executable trajectory generation. Simulations and real-world experiments demonstrate safe and executable aerial manipulation in complex environments.

0.35

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

cs.RO ·2026-08-24 ·Aniketh Parkala, Harikumar Kandath
published similarity 0.65
Abstract · 8 pages

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

0.33

Aerial Layouting: Design and Control of a Compliant and Actuated End-Effector for Precise In-flight Marking on Ceilings

cs.RO ·2026-08-11 ·Christian Lanegger, Marco Ruggia, Marco Tognon, Lionel Ott, Roland Siegwart
publishedhighly cited similarity 0.65
Abstract · C. Lanegger and M. Ruggia contributed equally. Accepted to Robotics: Science and Systems (RSS) 2022

Aerial robots have demonstrated impressive feats of precise control, such as dynamic flight through openings or highly complex choreographies. Despite the accuracy needed for these tasks, there are problems that require levels of precision that are challenging to achieve today. One such problem is aerial interaction. Advances in aerial robot design and control have made such contact-based tasks possible and opened up research into challenging real-world tasks, including contact-based inspection. However, while centimetre accuracy is sufficient and achievable for inspection tasks, the positioning accuracy needed for other problems, such as layouting on construction sites or general push-and-slide tasks, is millimetres. To achieve such a high precision, we propose a new aerial system composed of an aerial vehicle equipped with a novel "smart" end-effector leveraging a stability-optimized Gough-Stewart mechanism. We present its design process and features incorporating the principles of compliance, multiple contact points, actuation, and self-containment. In experiments, we verify that the design choices made for our novel end-effector are necessary to obtain the desired positioning precision. Furthermore, we demonstrate that we can reliably mark lines on ceilings with millimetre accuracy without the need for precise modeling or sophisticated control of the aerial robot.

0.61

Contact-Aware Incremental Model Predictive Control for an Underactuated Aerial Manipulator

cs.RO ·2026-09-10 ·Darwin Liu, Tamas Keviczky, Sihao Sun
top venue similarity 0.64
Abstract · 8 pages, 6 figures

We present a robust contact-aware control framework for aerial writing on an underactuated platform. The framework combines nonlinear model predictive control (NMPC) for accurate end-effector position and normal-force tracking at small reference penetration depths, with consistent performance across controller tunings, with whole-body incremental nonlinear dynamic inversion (INDI) for robustness to frictional and aerodynamic disturbances during contact. The proposed controllers are validated on a quadrotor-based aerial manipulator with a rigid, single-link, one-degree-of-freedom (DoF) arm in simulation and real-world experiments. The aerial writing experiments span vertical and inclined surfaces, multiple reference forces, different friction conditions, and wind disturbances. The results demonstrate that robust simultaneous five-DoF end-effector pose and contact-force tracking is achievable on a standard underactuated quadrotor with a simple, rigid, single-link arm, without requiring a fully actuated platform, a complex arm, or dedicated force/torque sensing.

0.39

A Morphing Aerial Robot With Thruster-Integrated Flexible Continuum Links for Shape Adaptive Aerial Manipulation

cs.RO ·2026-09-16 ·Eri Sawada, Kazuki Sugihara, Ayano Miyamichi, Kunio Kojima, Kei Okada
published similarity 0.63
Abstract · Accepted to 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS)

In recent years, aerial manipulation has attracted increasing attention as a key to expand the application of aerial robots. In this work, we focus on two major research directions for achieving versatile aerial manipulation: (i) acquiring high environmental adaptability using soft manipulators, and (ii) expanding the feasible wrench space by distributing thrusters along the manipulator. However, no aerial robot has simultaneously satisfied these two requirements. Therefore, in this paper, we propose a morphing rotor-distributed aerial robot with flexible continuum links that achieves both high shape adaptability and an expanded wrench space. The flexible continuum links function as soft manipulators, passively conforming to the shape of the environment, while the thrusters distributed along the continuum links expand the feasible thrust wrench space and enable the end-effector to exert large interaction forces. To realize the proposed robot, it is essential to suppress vibrations of the lightweight continuum links. Thus, we develop a composite leaf-spring structure that provides both high torsional and vertical stiffness, and vibration-suppressing control methods. Using these implementations, we demonstrate stable flight and a variety of aerial manipulation tasks. To the best of our knowledge, this is the first work to realize aerial manipulations using flexible links with an integrated thruster.

0.29

Robust Sliding Mode and Admittance Control of Underactuated Aerial Manipulators for Contact-Based Inspection

cs.RO ·2026-08-11 ·Tareq Aziz Alqutami, Yvan Petillot, Matthew W. Dunnigan, Mustafa Suphi Erden
published similarity 0.63
Abstract · 6 pages, 7 figures, submitted to 2026 IEEE Industrial Electronics and Applications Conference (IEACon)

Contact-based industrial inspection requires aerial platforms to maintain stable interaction while rejecting disturbances. Underactuated aerial manipulators present control challenges due to the dynamic coupling between vehicle attitude and force generation. This paper proposes a robust control framework for an underactuated hexarotor equipped with a 1-DoF manipulator to perform sustained contact inspection. The architecture integrates integral-augmented Sliding Mode Control (SMC) for trajectory tracking with an admittance control law for force regulation. The contact force is mapped to a feedforward attitude term, while the 1-DoF arm actively compensates for the tilt to maintain surface alignment. Software-in-the-loop simulations demonstrate that the SMC-based approach achieves superior tracking and coupling rejection compared to traditional PID. Furthermore, the interaction strategy achieved precise force regulation with an RMSE of 0.12N and was able to stably exert up to 20N force, confirming the system's efficacy for stable, reliable contact-based inspection.

0.26