CS Paper Radar

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

Aniketh Parkala, Harikumar Kandath

cs.RO ·submitted 2026-08-24 12:11 UTC · v1
published

Abstract

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

Comment
8 pages
Journal ref
2026 International Conference on Unmanned Aircraft Systems (ICUAS)
DOI
10.1109/ICUAS69441.2026.11598692

Closest papers

Nearest neighbours by meaning across the whole index.

A Two-Wheeled Quadrotor with All-Clockwise Tilted Rotors for Level-Attitude Surface Locomotnion

cs.RO eess.SY ·2026-10-29 ·Takumi Ito, Satoshi Nakano
similarity 0.69
Abstract

Conventional wheel-equipped quadrotor UAVs must tilt their bodies to generate lateral forces, limiting their ability to maintain a desired attitude during lateral motion. This paper proposes a wheeled quadrotor with all-clockwise tilted rotors that uses surface contact as a constraint to generate propulsion along the contact surface without tilting the vehicle. We analyze feasible forces and system controllability under surface contact and optimize the vehicle design considering different rotor-spin configurations. The optimization results show that a configuration in which all four rotors spin clockwise can generate a larger tangential force than the conventional alternating-spin configuration. This approach enables both aerial and contact-based locomotion without additional rotor-tilting actuators or mechanisms. Simulation results demonstrate both hovering in free space and horizontal locomotion on a floor while maintaining a level attitude.

0.21

From Model to Prototype: Design and Motor-Flap Propulsion Control of a Twin-Wing Metamorphic UAV

cs.RO ·2026-10-06 ·Anja Bosak, Dorian Erić, Ana Milas, Stjepan Bogdan
similarity 0.66
Abstract · 8 pages, 12 figures

This paper presents the design and control strategy for MetaMorpher, a metamorphic Unmanned Aerial Vehicle (UAV), capable of both spinning-wing hover and fixed flying-wing cruise flight. Since control of the cruise configuration is comparatively well established in the literature, this paper focuses on control of the MetaMorpher in hover mode, building on the flight dynamics model and conceptual design validated in previous work. The control algorithm is implemented using one of two phase-synchronized strategies: motor propulsion, which pulses motor thrust in synchrony with the vehicle's rotation, or flap propulsion, a novel strategy that pulses the deflection of the wing-mounted elevons. We evaluate both strategies in simulation through different flight experiments. Simulation results confirm the mathematical model and show stable reference tracking, demonstrating flap propulsion as a lightweight, decoupled alternative for hover control. Experimental testing validated the vertical-dynamics propulsion model against the physical prototype, demonstrating very good steady-state agreement across different configurations.

0.22

DuctAM: A Duct-Assisted Quadrotor-Based Aerial Manipulator Enabling High-Force Push-and-Pull Interactions

cs.RO ·2026-09-14 ·Yi Wang, Rui Jin, Xinhang Xu, Haotian Jin, Ruiyang Liu +2 more
highly cited similarity 0.65
Abstract

Uncrewed Aerial Manipulators (UAMs) extend the capabilities of Uncrewed Aerial Vehicles (UAVs) from perception to physical interaction. Among various aerial interactions, push-and-pull operations are fundamental manipulation primitives that require sustained horizontal forces while maintaining stable flight. In this paper, we propose DuctAM, a compact aerial manipulation platform that enhances horizontal force capability for push-and-pull interactions using two ducted fans integrated along the quadrotor interaction axis. An attitude-force decoupled control scheme enables controllable horizontal forces without requiring large attitude changes. Extensive real-world experiments are conducted to validate the DuctAM. Figure-eight trajectory tracking experiments demonstrate stable flight and accurate motion control in both quad and duct modes. Force-measurement experiments quantify the decoupled longitudinal force capability of DuctAM. Finally, representative push-and-pull interaction tasks, including cart pushing, door closing, and drawer opening, verify the practical effectiveness of DuctAM. The results show that DuctAM achieves significantly improved horizontal interaction force capability while maintaining stable flight compared with conventional UAVs.

0.40

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.61
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.59
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.50

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

cs.RO eess.SY ·2026-09-17 ·Ali Jokar, Amin Talaeizadeh, Aria Alasty
similarity 0.58
Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

0.13

Mass Scaling Laws for Energy-Optimal Horizontal Multirotor Flight

cs.RO eess.SY ·2026-11-03 ·Ayush Patnaik, Nicolas Michel, Leonard Baursfeld, Davide Scaramuzza, Xinfan Lin
top venue similarity 0.57
Abstract · Accepted to IEEE Robotics and Automation Letters, October 2026

Multicopters are a type of aerial robot seeing extensive real-world applications but with range and endurance as critical bottlenecks. Optimization of its energy efficiency through energy-aware flight planning (e.g. cruise speed-scheduling) has hence been an important topic. The mass of the multicopter is an important factor to consider, as it has a significant impact on efficiency, and many common applications are subject to frequent mass variation due to payload change. This work derives closed-form scaling relationships between the energy-optimal steady horizontal flight behavior of a multicopter and its vehicle mass, and validates them experimentally on two multirotor platforms. Specifically, for mass-only variation, i.e., when payload changes the vehicle mass while the airframe geometry, aerodynamic characteristics, and rotor configuration remain unchanged, we show through a combination of numerical simulation, theoretical derivation, and experimental validation that (1) the energy-optimal velocity is proportional to the square root of vehicle mass; (2) the energy-optimal pitch angle is constant with respect to mass; and (3) the optimal energy per meter is proportional to mass. The analysis shows that these three relationships arise from a common mass-similarity property of the steady-state flight and rotor-aerodynamic equations. Furthermore, the obtained scaling relationships enable simple yet effective cruise-speed planning to optimize energy efficiency and extend the range and endurance of the multicopter.

0.45

Learning to Exploit Passive Dynamics for Energy-Efficient Target Hopping of a Spring-Legged Quadcopter

cs.RO cs.LG ·2026-09-14 ·Ruigang Chen, Qi Zhang, Zhicheng Zhong, Zhuorui Yun, Yizhar Or +1 more
similarity 0.57
Abstract · 8 pages, 10 figures

Combining aerial thrust with spring-loaded hopping makes monopedal quadcopters promising for locomotion over complex terrain, but heuristic proportional-integral-derivative (PID) tuning limits coordination between active thrust and passive contact dynamics. We present a direct estimated-state-to-motor Proximal Policy Optimization (PPO) policy that commands four motors without an explicit hopping state machine or low-level attitude PID. Its reward combines Energy-Manifold Shaping for mass-normalized vertical-energy tracking and apex-state anchoring with Efficiency Shaping, which uses a history-aware power estimator to penalize general power use, impose an additional airborne-power cost, and penalize airborne near-stationarity. In representative hardware runs, the PPO-based control stack reduced cycle-averaged measured electrical power by 30.7% and mean total normalized thrust by 49.8% relative to the tuned PID-based control stack, while retaining repeatable commanded-height hopping and more concentrated landings. These observations are consistent with improved use of passive dynamics and reduced measured electrical demand.

0.29