CS Paper Radar

From Model to Prototype: Design and Motor-Flap Propulsion Control of a Twin-Wing Metamorphic UAV

Anja Bosak, Dorian Erić, Ana Milas, Stjepan Bogdan

cs.RO ·submitted 2026-10-06 07:43 UTC · v1

Abstract

This paper presents the design and control strategy for MetaMorpher, a metamorphic Unmanned Aerial Vehicle (UAV), capable of both spinning-wing hover and fixed flying-wing cruise flight. Since control of the cruise configuration is comparatively well established in the literature, this paper focuses on control of the MetaMorpher in hover mode, building on the flight dynamics model and conceptual design validated in previous work. The control algorithm is implemented using one of two phase-synchronized strategies: motor propulsion, which pulses motor thrust in synchrony with the vehicle's rotation, or flap propulsion, a novel strategy that pulses the deflection of the wing-mounted elevons. We evaluate both strategies in simulation through different flight experiments. Simulation results confirm the mathematical model and show stable reference tracking, demonstrating flap propulsion as a lightweight, decoupled alternative for hover control. Experimental testing validated the vertical-dynamics propulsion model against the physical prototype, demonstrating very good steady-state agreement across different configurations.

Comment
8 pages, 12 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

cs.RO ·2026-08-24 ·Aniketh Parkala, Harikumar Kandath
published similarity 0.66
Abstract · 8 pages

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

0.33

Self-excited actuation enables adaptive and resilient flapping-wing flight

cs.RO ·2026-09-16 ·Rundong Yang, Ethan S. Wold, Ellen Liu, James Lynch, Wei Zhou +3 more
similarity 0.64
Abstract

The muscles that power insect flight fall into one of two categories: 1) synchronous muscles that contract under direct control from the nervous system, and 2) asynchronous muscles which have an intrinsic stretch activation response that spontaneously generates wingbeats without the need for signaling from the brain. It is thought that the emergent nature of asynchronous wingbeats provides both adaptive and responsive capabilities for flight control. To date, most flying robots use synchronous actuation. In this paper we develop the first flight-capable flapping wing robot that uses asynchronous actuation. We demonstrate that asynchronous actuation allows wings to respond to changes in the resonant mechanics of the body without control input, and wings can react instantaneously to collisions with obstacles with no extrinsic sensing needed. Flight tests within cluttered environments demonstrate that asynchronous actuation significantly improves stability and performance when compared to synchronous actuation. In total this work demonstrates that a flapping wing robot actuation strategy that emulates the asynchronous muscles of flying insects can provide fast, reactive actuation responses before a control system would need to intervene. This partitioning of embodied control to both the low-level actuation dynamics and and high-level sensorimotor system provides a compelling blueprint for new flying robots.

0.23

Aerodynamic Prior-Free Coordinated Trajectory Generation and Tracking Control for a Tail-Sitter UAV

cs.RO ·2026-09-10 ·Erchao Rong, Zihao Liu, Junning Liang, Jianguo Wang, Xiao Jie +3 more
top venuecode/data similarity 0.62
Abstract

This paper presents a coordinated trajectory generation and tracking control framework for a tail-sitter unmanned aerial vehicle (UAV), which does not require aerodynamic priors identified for a specific airframe while addressing the challenge of flight control under highly nonlinear aerodynamics across the full flight envelope. The core innovation lies in employing phase-specific aerodynamic modeling strategies for planning and tracking, tailored to their distinct functional characteristics, without requiring airframe-specific aerodynamic priors. Specifically, the phi-theory model under coordinated flight is employed to derive an analytic differential flatness mapping, and a simplified but locally accurate model is established for predictive control to enable real-time aerodynamic parameter estimation. The proposed framework is evaluated extensively through both simulation and challenging real-world flight tests under mild wind conditions, showing high-precision tracking and adaptability across the tested aerodynamic conditions. To the best of our knowledge, this is the first real-world demonstration of accurate trajectory tracking over tested flight regimes spanning the full envelope of a tail-sitter UAV without relying on aerodynamic identification campaigns. The source code of our framework is available at: https://github.com/SYSU-HILAB/AP-PnC.

0.34

Taming the Tilt: A Unified Pilot Control Concept for Transformational eVTOL Aircraft

eess.SY math.OC ·2026-08-20 ·Daniel Milz, Marc May, Andreas Seefried, Tobias Bellmann
published similarity 0.60
Abstract · Accepted for publication in "Aerospace Systems", 31 pages, 16 figures

Transformational electric vertical take-off and landing (eVTOL) vehicles have gained significant attention over the past decade due to their efficient wing-borne cruise capabilities and reduced reliance on ground-based infrastructure. However, control system design for these vehicles remains challenging, as they must operate across multiple flight phases, each with distinct dominant dynamics. If left unaddressed, this complexity would significantly increase pilot workload, thus motivating the development of pilot control systems for multi-phase flight operations. The Simplified Vehicle Operations concept presents a promising strategy for reducing pilot workload. This study presents the design and implementation of a novel pilot control concept for eVTOL aircraft, validated through a tandem tilt-wing aircraft simulation on a full-motion simulator equipped with an active, force-feedback side stick. The system provides pilots with tactile feedback during specific flight phases, supporting intuitive control. The proposed approach enables seamless transitions and multi-phase flight maneuvers by leveraging the available degrees of freedom. Furthermore, an optimal-control-based methodology is proposed as a metric to evaluate command-filter-induced performance penalties and inceptor activities. The results show that the proposed command filter does not significantly increase the mission duration compared to the closed-loop system, while the active side stick helps reduce inceptor activity.

0.40

FlapSim: A Composable MuJoCo Simulation Platform and Reduced-Order Aerodynamic Model Hierarchy for Flapping-Wing Robotics

cs.RO ·2026-10-29 ·Mingshan He
code/data similarity 0.60
Abstract

Flapping-wing simulation need to reconcile high-frequency wingbeat aerodynamics with the slower dynamics relevant to flight control and reinforcement learning. We present FlapSim, a modular open-source MuJoCo simulation platform that combines robot descriptions, wing geometry, and composable aerodynamic models in a deterministic simulation pipeline. Across $48$ held-out scenarios spanning frequency, gimbal, wind, frequency-step, gust, and cross-robot flat-plate regimes, we compare five reduced-order configurations operating at $1\,\text{ms}$ with a $50\,μ\text{s}$ quasi-steady blade-element reference. The built-in hover cycle-averaged baseline achieves a $67.51\times$ CPU speedup but only $0.6593$ mean wrench fidelity. Combining multirate $21$-substep clock synchronization, three-dimensional linear/quadratic inflow and gust coupling, analytical blade-element geometry scaling, and phase-locked $1f\text{--}6f$ harmonics raises mean fidelity to $0.9646$ at a $65.19\times$ speedup in a five-block model. A streamlined four-block model without explicit step-transient lag states achieves $0.9662$ fidelity at a $67.98\times$ speedup. Controlled ablations show that stroke harmonics are particularly important during frequency transitions, improving held-out frequency-step fidelity by $+0.3176$. Transfer-function analysis explains this effect: fixed-window cycle averaging retains harmonic contributions when the wingbeat frequency changes, so within-cycle reconstruction also improves the filtered wrench. These results characterize the accuracy--computation tradeoff of the aerodynamic hierarchy and identify timing, inflow, geometry, and harmonic representation as central considerations for reduced-order flapping-wing simulation. The source code are available at: https://mingshanhe.github.io/FlapSim/\href{https://mingshanhe.github.io/FlapSim/}.

0.35

Trajectory Inversion for a Rudderless Dual Vectored-Thrust Flying Wing

cs.RO ·2026-11-07 ·Weicheng Di, Qiqi Liu, Jinwu Xiang, Daochun Li, Zhan Tu
similarity 0.60
Abstract

A rudderless dual vectored-thrust flying wing combines vertical takeoff and landing with efficient for- ward flight in a compact tailless configuration. Without aerodynamic control surfaces, vectored thrust couples translation and pitch control. Therefore, generating dy- namically compatible trajectories remains an open chal- lenge. To address this challenge, this study proposes a trajectory generation method that jointly optimizes path geometry and timing. Trajectory inversion yields state and control histories that satisfy the coupled equations of motion. The optimization balances curvature-induced acceleration against aerodynamic support, lowering thrust- vectoring demand while retaining the defining maneuver features. Representative looping and rolling sequences are tracked in closed-loop simulations. These results provide a basis for planning autonomous aerobatic maneuvers with rudderless vectored-thrust aircraft.

0.31

Dynamic System Emulation: Fixed Wing Dynamics on a Multicopter

eess.SY cs.RO ·2026-09-06 ·Abdelhakim Amer, Andriy Sarabakha
similarity 0.60
Abstract · 7 pages, 6 figures

This work presents a control framework that enables a multicopter equipped with a two-axis gimbal to emulate the flight dynamics of a fixed-wing aircraft. The goal is to provide an operationally simple platform for training and simulation that avoids the aerodynamic constraints of fixed-wing vehicles, such as minimum airspeed and nonholonomic constraints. A state-input mapping between the two platforms is derived using dynamic feedback linearization. The framework is evaluated on representative fixed-wing manoeuvres. Results show high-fidelity emulation under nominal conditions. While evaluations are conducted in simulation, the approach establishes a practical path toward hardware deployment for pilot training, autonomy research, and controller benchmarking.

0.27

Task-Driven Closed-Loop Design Optimization of Passively Morphing Quadrotors for Contact-Mediated Narrow Gap Traversal

cs.RO ·2026-11-06 ·Etor Arza, Luca Girardi, Gabriel Maquignaz, Javier Paez, Stefan Leutenegger +2 more
code/data similarity 0.59
Abstract · Video: https://youtu.be/xGkEtl6-vCA. Code: https://github.com/ntnu-arl/soft-quadrotor-optimization

Aerial robots operating in cluttered environments may encounter openings narrower than their nominal width. Existing passively morphing drones reduce their width upon traversal, but they typically involve human-made designs, which can struggle to find the right balance among folding ratio, flight efficiency, and control tracking performance. We introduce a closed-loop design method that jointly optimizes quadrotor geometry and the torque-deflection response of two passively folding arms driven by the success rate in simulation for contact-mediated gap traversal. An optimization algorithm samples candidate designs that are evaluated in a contact-based simulation of the traversal task, where the task success rate is used as a feedback signal to sample progressively better designs over time. The resulting prototype passively reduces its width from 31.3 to 14.1 cm and traverses a 15 cm wide opening at a 2 m/s reference speed. It also tolerates gap approach-angle errors of up to 30 degrees and folds through a 40 cm long confined passage. Compared to a rigid twin, the soft configuration adds only 2 mm of position RMSE and less than 1% electrical power during contact-free flight. These results show that task-driven closed-loop design optimization can produce passively morphing airframes that are compact under contact, tolerant to approach error, and effectively rigid during nominal flight.

0.28