CS Paper Radar

Mass Scaling Laws for Energy-Optimal Horizontal Multirotor Flight

Ayush Patnaik, Nicolas Michel, Leonard Baursfeld, Davide Scaramuzza, Xinfan Lin

cs.RO eess.SY ·submitted 2026-11-03 12:02 UTC · v2
top venue

Abstract

Multicopters are a type of aerial robot seeing extensive real-world applications but with range and endurance as critical bottlenecks. Optimization of its energy efficiency through energy-aware flight planning (e.g. cruise speed-scheduling) has hence been an important topic. The mass of the multicopter is an important factor to consider, as it has a significant impact on efficiency, and many common applications are subject to frequent mass variation due to payload change. This work derives closed-form scaling relationships between the energy-optimal steady horizontal flight behavior of a multicopter and its vehicle mass, and validates them experimentally on two multirotor platforms. Specifically, for mass-only variation, i.e., when payload changes the vehicle mass while the airframe geometry, aerodynamic characteristics, and rotor configuration remain unchanged, we show through a combination of numerical simulation, theoretical derivation, and experimental validation that (1) the energy-optimal velocity is proportional to the square root of vehicle mass; (2) the energy-optimal pitch angle is constant with respect to mass; and (3) the optimal energy per meter is proportional to mass. The analysis shows that these three relationships arise from a common mass-similarity property of the steady-state flight and rotor-aerodynamic equations. Furthermore, the obtained scaling relationships enable simple yet effective cruise-speed planning to optimize energy efficiency and extend the range and endurance of the multicopter.

Comment
Accepted to IEEE Robotics and Automation Letters, October 2026
DOI
10.1109/LRA.2026.3751905

Closest papers

Nearest neighbours by meaning across the whole index.

From Ideal Motion to Flight-Executable Communications: LLM-Evolved Multi-UAV Deployment for Cell-Free Massive MIMO

eess.SP ·2026-09-21 ·Yuyao Wang, Gaoze Mu, Yongan Zheng, Yanzhao Hou, Qingqing Wu +3 more
similarity 0.59
Abstract · 13 pages. 12 figures

Cell-free massive multiple-input multiple-output (CF-mMIMO) is a promising paradigm for future wireless networks, providing user-centric services and cooperative coverage. By using unmanned aerial vehicles (UAVs) as aerial access points, CF-mMIMO networks can exploit UAV mobility to enhance three-dimensional (3D) coverage and spectral efficiency (SE). However, most existing studies on UAV deployment for communication optimization typically assume that UAVs follow ideal point-mass motion (IM), neglecting flight-control constraints and finite-horizon position errors in real flight execution. Consequently, IM-trained deployment policies may degrade severely or become difficult to execute in practice. Motivated by this, we model each UAV as a six-degree-of-freedom quadrotor rigid body with a cascaded flight controller to capture the impact of flight-control-constrained motion (FM) on communication optimization. Based on this model, we formulate a joint UAV 3D deployment and power allocation problem under FM to maximize the downlink average SE in CF-mMIMO networks. To address this problem, we propose LERE, a large language model (LLM)-enhanced multi-agent reinforcement learning (MARL) framework. In LERE, the LLM evolves hybrid rewards with both global and local components via multi-level feedback. The evolved hybrid rewards guide MARL policy optimization and promote multi-UAV cooperation. Experimental results demonstrate that LERE achieves higher SE than reward-design baselines while substantially reducing UAV position errors. Notably, when tested under FM execution, the FM-trained LERE policy achieves a 60.49\% SE gain over its IM-trained counterpart, confirming the necessity of incorporating flight-control constraints into UAV-enabled CF-mMIMO optimization.

0.18

Optimized Modular Design and Development of a Tilt-Rotor Bicopter Drone

cs.RO ·2026-08-31 ·Saideep Verma, Nimisha Tatapudi, Akshay Arjun, Danwada Sharanya Sukka, Abhishek Sarkar +1 more
similarity 0.58
Abstract · 7 pages, conference, Index terms -Tilt-Rotor Bicopter Drone, Optimal Modular Design, Static Analysis, Dynamic Flight Analysis

Hybrid systems like tilt-rotor bicopter drones combine the beneficial characteristics of both fixed-wing and rotary-wing technology, enabling long endurance and VTOL capability. However, such drones also require an optimum design to ensure both static and dynamic stability. The modular design of a traditional bicopter is developed in this paper based on extensive analysis and in-depth structural and aerodynamic simulations. The structural analysis has been performed to ensure that the aircraft's structure withstands the stresses encountered during different flight modes. Controlling the relative positions of the Center of Gravity (CG) and Neutral Point (NP) is an essential aspect of the design, ensuring stability during hover and positive stability during forward flight. The thrust and power analyses have been conducted to assess the flight performance and endurance. After analysis, the drone has been developed, and flight tests with a basic flight controller were conducted to validate the performance metrics obtained in the simulation.

0.24

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

cs.RO ·2026-08-24 ·Aniketh Parkala, Harikumar Kandath
published similarity 0.57
Abstract · 8 pages

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

0.33

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

cs.RO eess.SY ·2026-09-17 ·Ali Jokar, Amin Talaeizadeh, Aria Alasty
similarity 0.57
Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

0.13

Nested Power Models for Multirotor Propulsion: From Aerodynamic Drag to Electrical Losses

cs.RO eess.SY ·2026-10-06 ·Antonio Franchi, Aaron Saini, Ahmed Ali, Chiara Gabellieri
unusual similarity 0.57
Abstract

Speed-only aerodynamic power models for multirotor propulsion cannot represent acceleration-dependent effects. This work develops a nested sequence of propulsion-power models that starts from aerodynamic power dissipation and progressively introduces a reversible kinetic-energy rate, torque-dependent electromechanical dissipation, and lumped speed-proportional dissipation. The models are identified using one subset of experiments and validated using the other on a motor-drive-propeller unit. Independent estimates of rotational inertia and aerodynamic drag complement predictive validation by assessing whether the models correctly attribute the measured power to reversible kinetic-energy exchange and irreversible dissipation and, within the latter, to aerodynamic and electromechanical losses. The results show that the reversible kinetic-energy rate is necessary but insufficient for accurate dynamic power prediction. Dissipation proportional to the squared motor torque provides the main additional improvement, while speed-proportional dissipation further prevents irreversible losses from being attributed to reversible kinetic-energy exchange. The resulting methodology provides a reusable and experimentally verifiable basis for developing and selecting dynamic propulsion-power models for multirotor systems.

0.25

System Identification of an Octocopter in Hover using Full-Harmonic Orthogonal Multisine Inputs

eess.SY cs.RO ·2026-09-24 ·Justin J. Matt, George V. Altamirano
published similarity 0.55
Abstract · 31 pages, 18 figures. Presented at the AIAA AVIATION Forum 2025. Accepted for publication in the AIAA Journal of Aircraft

A new method for multi-input flight maneuver design for system identification is presented. The method consists of injecting "full-harmonic" orthogonal multisine signals into the flight control system. Orthogonality is achieved by repeating maneuvers with changing multisine polarities. The multisines can contain the same frequency content, which can simplify frequency response estimation and allow for long flight maneuvers to be split into several shorter maneuvers while maintaining the same frequency resolution and minimum frequency. An input allocation scheme is presented that augments the multisines to size the vehicle response amplitude about a specific degree of freedom. The developed approach was demonstrated through flight testing of a small octocopter in near-hover conditions. The input allocation scheme was utilized successfully to increase excitation about the yaw axis. Electrical power, motor speed, and rigid-body dynamic models were identified and are shown to predict the vehicle and motor responses accurately. The models are parameterized primarily by rotor thrust and torque coefficients, making them suitable for analysis of aircraft flight dynamics and individual rotor aerodynamics. The results demonstrate that the near-hover flight dynamics can be modeled accurately by neglecting rotor hub moments, variations in rotor coefficients, gyroscopic moments in roll and pitch, and aerodynamic interaction effects.

0.56

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.55
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.51

Learning to Exploit Passive Dynamics for Energy-Efficient Target Hopping of a Spring-Legged Quadcopter

cs.RO cs.LG ·2026-09-14 ·Ruigang Chen, Qi Zhang, Zhicheng Zhong, Zhuorui Yun, Yizhar Or +1 more
similarity 0.53
Abstract · 8 pages, 10 figures

Combining aerial thrust with spring-loaded hopping makes monopedal quadcopters promising for locomotion over complex terrain, but heuristic proportional-integral-derivative (PID) tuning limits coordination between active thrust and passive contact dynamics. We present a direct estimated-state-to-motor Proximal Policy Optimization (PPO) policy that commands four motors without an explicit hopping state machine or low-level attitude PID. Its reward combines Energy-Manifold Shaping for mass-normalized vertical-energy tracking and apex-state anchoring with Efficiency Shaping, which uses a history-aware power estimator to penalize general power use, impose an additional airborne-power cost, and penalize airborne near-stationarity. In representative hardware runs, the PPO-based control stack reduced cycle-averaged measured electrical power by 30.7% and mean total normalized thrust by 49.8% relative to the tuned PID-based control stack, while retaining repeatable commanded-height hopping and more concentrated landings. These observations are consistent with improved use of passive dynamics and reduced measured electrical demand.

0.29