CS Paper Radar

A Two-Wheeled Quadrotor with All-Clockwise Tilted Rotors for Level-Attitude Surface Locomotnion

Takumi Ito, Satoshi Nakano

cs.RO eess.SY ·submitted 2026-10-29 17:20 UTC · v1

Abstract

Conventional wheel-equipped quadrotor UAVs must tilt their bodies to generate lateral forces, limiting their ability to maintain a desired attitude during lateral motion. This paper proposes a wheeled quadrotor with all-clockwise tilted rotors that uses surface contact as a constraint to generate propulsion along the contact surface without tilting the vehicle. We analyze feasible forces and system controllability under surface contact and optimize the vehicle design considering different rotor-spin configurations. The optimization results show that a configuration in which all four rotors spin clockwise can generate a larger tangential force than the conventional alternating-spin configuration. This approach enables both aerial and contact-based locomotion without additional rotor-tilting actuators or mechanisms. Simulation results demonstrate both hovering in free space and horizontal locomotion on a floor while maintaining a level attitude.

Closest papers

Nearest neighbours by meaning across the whole index.

Spinning Quadrotor: Hover Thrust Augmentation with Passive Lifting Surfaces

cs.RO ·2026-08-24 ·Aniketh Parkala, Harikumar Kandath
published similarity 0.69
Abstract · 8 pages

Conventional multirotor aerial vehicles actively suppress yaw rotation during hover, expending power to maintain a fixed heading despite the fact that yaw regulation is not required for force balance or altitude control. This paper challenges that paradigm by proposing a spinning quadrotor architecture that intentionally operates at a sustained yaw rate, converting power traditionally spent on yaw regulation into useful aerodynamic effects. A dynamic model of the spinning quadrotor is developed, analysis for low Re range is conducted to choose an airfoil for lifting surfaces. Preliminary hardware tests show a 22% reduction in thrust required. These findings suggest that intentional yaw rotation, rather than being suppressed, can be exploited as a design mechanism for efficient and robust multirotor flight.

0.33

FAM-DQ: A Dual-Quadrotor-Based Fully Actuated Aerial Manipulator for High-Torque Interaction

cs.RO ·2026-08-13 ·Xuwei Yang, Ruoyu Ren, Ziqian Guo
similarity 0.64
Abstract · 7 pages, 7 figures

Aerial physical interaction requires aerial manipulation platforms to generate large interaction forces and torques while maintaining precise end-effector control. However, conventional underactuated aerial manipulators suffer from strong position-attitude coupling, whereas fully actuated platform designs often face structural complexity, limited payload capacity, and insufficient torque output. This paper presents FAM-DQ, a dual-quadrotor based fully actuated aerial manipulator designed for high-torque physical interaction tasks. By mounting two quadrotor propulsion modules at the ends of a central frame through passive joints, while using a gear-driven servo to regulate the pointing direction, FAM-DQ achieves decoupled $6$-DoF end-effector control with omnidirectional manipulation capability and enhanced torque output. Experiments including trajectory tracking, attitude tracking, static torque measurement, and screw driving validate the proposed design. FAM-DQ achieves a maximum torque of $1.019~\mathrm{N}\cdot\mathrm{m}$ with a total mass of $0.447~\mathrm{kg}$, corresponding to a torque-to-mass ratio of $2.28~\mathrm{N}\cdot\mathrm{m/kg}$.

0.07

DuctAM: A Duct-Assisted Quadrotor-Based Aerial Manipulator Enabling High-Force Push-and-Pull Interactions

cs.RO ·2026-09-14 ·Yi Wang, Rui Jin, Xinhang Xu, Haotian Jin, Ruiyang Liu +2 more
highly cited similarity 0.63
Abstract

Uncrewed Aerial Manipulators (UAMs) extend the capabilities of Uncrewed Aerial Vehicles (UAVs) from perception to physical interaction. Among various aerial interactions, push-and-pull operations are fundamental manipulation primitives that require sustained horizontal forces while maintaining stable flight. In this paper, we propose DuctAM, a compact aerial manipulation platform that enhances horizontal force capability for push-and-pull interactions using two ducted fans integrated along the quadrotor interaction axis. An attitude-force decoupled control scheme enables controllable horizontal forces without requiring large attitude changes. Extensive real-world experiments are conducted to validate the DuctAM. Figure-eight trajectory tracking experiments demonstrate stable flight and accurate motion control in both quad and duct modes. Force-measurement experiments quantify the decoupled longitudinal force capability of DuctAM. Finally, representative push-and-pull interaction tasks, including cart pushing, door closing, and drawer opening, verify the practical effectiveness of DuctAM. The results show that DuctAM achieves significantly improved horizontal interaction force capability while maintaining stable flight compared with conventional UAVs.

0.40

Task-Driven Closed-Loop Design Optimization of Passively Morphing Quadrotors for Contact-Mediated Narrow Gap Traversal

cs.RO ·2026-11-06 ·Etor Arza, Luca Girardi, Gabriel Maquignaz, Javier Paez, Stefan Leutenegger +2 more
code/data similarity 0.59
Abstract · Video: https://youtu.be/xGkEtl6-vCA. Code: https://github.com/ntnu-arl/soft-quadrotor-optimization

Aerial robots operating in cluttered environments may encounter openings narrower than their nominal width. Existing passively morphing drones reduce their width upon traversal, but they typically involve human-made designs, which can struggle to find the right balance among folding ratio, flight efficiency, and control tracking performance. We introduce a closed-loop design method that jointly optimizes quadrotor geometry and the torque-deflection response of two passively folding arms driven by the success rate in simulation for contact-mediated gap traversal. An optimization algorithm samples candidate designs that are evaluated in a contact-based simulation of the traversal task, where the task success rate is used as a feedback signal to sample progressively better designs over time. The resulting prototype passively reduces its width from 31.3 to 14.1 cm and traverses a 15 cm wide opening at a 2 m/s reference speed. It also tolerates gap approach-angle errors of up to 30 degrees and folds through a 40 cm long confined passage. Compared to a rigid twin, the soft configuration adds only 2 mm of position RMSE and less than 1% electrical power during contact-free flight. These results show that task-driven closed-loop design optimization can produce passively morphing airframes that are compact under contact, tolerant to approach error, and effectively rigid during nominal flight.

0.28

Nonlinear Control of Aerial Manipulator

eess.SY cs.RO ·2026-10-25 ·Sandesh Thapa
similarity 0.58
Abstract · 5 pages, 9 figures, 2 tables

This paper presents two controllers for a quadrotor equipped with a two-DOF robot manipulator that physically interacts with the environment. Cartesian impedance and adaptive sliding mode controllers are implemented and compared for a simple hovering task in the presence of some bounded disturbance. A full dynamic model is developed, and the two above controllers are implemented with the same initial conditions and desired position.

0.27

Trajectory Generation and Control for Quadrotors

eess.SY cs.RO ·2026-10-25 ·Sandesh Thapa
similarity 0.57
Abstract · 8 pages, 6 figures

In this project, I explored controller design and trajectory generation for a quadrotor. Differential flatness was used for trajectory generation based on one of the references. A minimum snap trajectory is generated from the given algorithm based on waypoint navigation, and a simple proportional plus derivative (PD) controller is used to track the trajectories. Simulation results are presented which generate smooth trajectories for position and velocity of the quadrotor.

0.31

From Sky to Soil: A Morphing Aerial-Ground Robot for Seed Deployment

cs.RO ·2026-09-29 ·Namai Chandra, Lining Yao
similarity 0.57
Abstract · 9 pages, 6 figures

Aerial seed broadcasting can reach remote restoration sites, but provides limited control over seed placement within the soil. This paper presents a geometry-assisted, tri-functional morphing robot that combines aerial access, ground locomotion, and controlled-depth seed embedding in a fly-drive-plant architecture. After landing, the platform reconfigures into a four-wheeled planting configuration: an electronically coupled dual-motor drive folds the rear arms outward to form ground wheels, while a descending front tray engages the propulsion motors with a drill gear train. Reusing the propulsion motors for drilling eliminates a dedicated drill drive. The planting sequence forms a hole, dispenses a seed, and allows the vehicle to reposition on the ground or return to its flight configuration. Ground mobility supports repeated planting without requiring a separate flight between adjacent sites. A companion controller issues reconfiguration, tray, and seed-gate commands, while a dedicated autopilot handles flight control. The morphing and planting mechanisms are validated using a hardware prototype that demonstrates ground repositioning and seed embedding. This proof of concept establishes a hardware basis for aerial-ground seed embedding through coordinated reconfiguration and actuator reuse.

0.24

From Model to Prototype: Design and Motor-Flap Propulsion Control of a Twin-Wing Metamorphic UAV

cs.RO ·2026-10-06 ·Anja Bosak, Dorian Erić, Ana Milas, Stjepan Bogdan
similarity 0.57
Abstract · 8 pages, 12 figures

This paper presents the design and control strategy for MetaMorpher, a metamorphic Unmanned Aerial Vehicle (UAV), capable of both spinning-wing hover and fixed flying-wing cruise flight. Since control of the cruise configuration is comparatively well established in the literature, this paper focuses on control of the MetaMorpher in hover mode, building on the flight dynamics model and conceptual design validated in previous work. The control algorithm is implemented using one of two phase-synchronized strategies: motor propulsion, which pulses motor thrust in synchrony with the vehicle's rotation, or flap propulsion, a novel strategy that pulses the deflection of the wing-mounted elevons. We evaluate both strategies in simulation through different flight experiments. Simulation results confirm the mathematical model and show stable reference tracking, demonstrating flap propulsion as a lightweight, decoupled alternative for hover control. Experimental testing validated the vertical-dynamics propulsion model against the physical prototype, demonstrating very good steady-state agreement across different configurations.

0.22