CS Paper Radar

Tether-Inertial Localization for Planetary Drones

Dielof van Loon, Anton Bredenbeck, Lennart Puck, Martin Azkarate, Salua Hamaza

cs.RO ·submitted 2026-08-10 12:15 UTC · v1
top venue

Abstract

Recent developments in planetary exploration have shown the potential of Unmanned Aerial Vehicles (UAVs), such as the Ingenuity helicopter that provided valuable mapping data. However, limited payload capabilities constrain the flight times and compute available for localization, which restrict their applicability. By providing a tethered connection, issues such as battery and computational constraints are offloaded to the base rover. At the same time, the cable can be exploited for non-drifting localization. This work presents a novel Tether-Inertial Localization approach that uses tether length and angle measurements to estimate the UAV position relative to its base. The method combines a computationally efficient analytical catenary model with a Gaussian Process (GP) residual error compensation. This accounts for systematic sensor inaccuracies and model limitations. Experimental validation across circular, triangular, and figure-eight trajectories with tether lengths up to 4.5 m and a total flight time of 37 minutes demonstrates the effectiveness of the proposed approach. Using only tether-based position estimates for feedback, the analytical catenary model achieves an average RMSE of 7.4 cm, which is further reduced to 5.2 cm through GP-based residual compensation, one order of magnitude better than the state-of-the-art. These results establish Tether-Inertial Localization as a practical alternative to vision- and GNSS-based localization for Tethered Unmanned Aerial Vehicles (TUAVs).

Closest papers

Nearest neighbours by meaning across the whole index.

Catenary Visibility: A Geometric Framework for Planning with Tethered Robots

cs.CG cs.RO ·2026-10-30 ·B. Ábrego, J. M. Díaz-Báñez, S. Fernández, D. Flores-Peñaloza, V. Sánchez-Canales
similarity 0.60
Abstract · 23 pages, 13 figures

This paper introduces \emph{catenary visibility}, a new geometric visibility concept for a robotic system consisting of a ground robot tethered to an aerial drone. The tether is modeled as an extensible catenary curve with bounded length, providing sustained power and significantly extending operational range. We define a point on the ground plane as \emph{catenary-visible} from a target point in 3D if there exists a collision-free catenary connecting them, given a set of obstacles. This paper introduces a geometric framework for visibility-aware planning of a tethered marsupial system, addressing the computational challenge of determining the feasible deployment locus: the collection of points in the ground plane that are catenary-visible from a given target in 3D space. We begin by solving the 2D subproblem, where the obstacles, target, and the ground vehicle's line of motion are all constrained to a single vertical plane. Our algorithm for this case computes the complete set of feasible launch points along the motion line and simultaneously determines the range of viable cable lengths for each. We also consider the query problem of finding all collision-free length ranges for a given location of the ground robot. Building upon this planar solution, we then generalize the approach to three dimensions, deriving a 3D solution for a constrained class of obstacles.

0.36

Vision-Based Control of a Tether-Suspended Aerial Radiation Sensing Payload

cs.RO ·2026-09-23 ·Ian Snider, Brian J. Quiter, Emil Rofors, Mark W. Mueller
survey similarity 0.59
Abstract · 7 pages, 7 figures, 2 tables. Submitted to IEEE ICRA 2027

Aerial radiation surveys achieve higher sensitivity when the radiation detector is held close to the ground. Detector sensitivity falls off roughly with the inverse square of the distance to the source, so a detector flown high is slower to reach a given minimum detectable activity. Flying the vehicle low puts the propellers near the ground, where downwash can disturb the surveyed area and resuspend contaminated particulates. Tether suspension decouples the detector from the vehicle altitude, but leaves the payload unactuated and only indirectly controllable. We therefore present a vision-based control approach for an aerial sensing payload suspended on a tether beneath a heavy-lift drone. Because a survey plan is decided as radiation detections arrive, we design a pilot aid for commanding the survey trajectory manually with a handheld transmitter. The controller regulates the payload, rather than the vehicle, onto that trajectory. The system uses onboard sensors with a downward-facing camera fixed to the drone body tracking a ring marker on the payload. A four-state Kalman filter estimates the tether swing angles and rates from payload bearing measurements, and a linear quadratic regulator with integral action takes the payload position as the regulated output. In outdoor flight tests under wind, the payload-aware controller reduced payload tracking error during transit by 20% when compared against a vehicle-referenced baseline, with the cost of higher peak error on arrival at a waypoint.

0.30

Real-Time Bounded Catenary Solver for UAV Tether Modeling

cs.RO ·2026-09-16 ·Max Beffert, Andreas Zell
similarity 0.57
Abstract

For non-stationary tethered multirotor UAVs in real-world conditions, simulating the forces imposed on the drone by the aerodynamic drag of the tether becomes crucial, with online use cases placing a hard bound on the maximum solve time. In previous work, a quasi-analytical catenary tether model reached a mean solve time of 0.51 ms using a general-purpose root finder, but without any worst-case guarantees or proven convergence. In this work, we reformulate the inner solver by reducing the catenary boundary-value problem to a single transcendental equation in one well-conditioned unknown. We derive a closed-form bracket and prove monotonicity and convexity as well as existence and uniqueness of the root, which together guarantee convergence of the solver. We further propose a two-regime initial guess which approximates the true root within 3.4 % and reduces the mean iteration count by 69.2 % to 2.24 compared to the textbook initialization. Building on the hybrid root-finding method rtsafe (Newton-Raphson with bisection fallback giving bounded iteration counts), we implement a specialized variant that exploits the problem structure to omit unnecessary checks while retaining correctness, which gives up to 1.37 times speedup. With the proposed solver the full tether model achieves a nearly constant solve time of 4.0 us on average and 4.6 us at worst, a 68 times speedup over an optimized re-implementation of the previous method, while agreeing with it to a relative deviation of 8.7e-9. Because the reformulation leaves the underlying physical model untouched, the experimental validation of the previous work carries over unchanged. We further demonstrate its suitability for embedded, resource-constrained platforms with a Lua implementation running directly in ArduPilot on a drone's flight controller, where it stays well inside the scheduling budget with a mean solve time of 0.74 ms.

0.22

Camera Calibration Using Inaccurate and Asynchronous Discrete GPS Trajectory from Drones

eess.SY cs.CV ·2026-08-27 ·R. Yang, Y. Bar-Shalom, H. A. J. Huang
theory similarity 0.57
Abstract · 11 pages, 12 figs, published on JAIF

This paper considers a stationary camera calibration problem, which estimates the camera orientation angles yaw, pitch and roll, using a drone trajectory recorded by a GPS. There are three challenges in using a GPS trajectory as ground truth for camera calibration. One, the altitude of GPS data is inaccurate with an unknown bias. Two, the GPS receiver and camera are not time synchronized, and there is an unknown time offset between the two systems. Three, the GPS trajectory is time-discrete and accurate interpolation is needed. This is actually an estimation problem since velocity is also needed. To address the first two challenges, we formulate the problem as a parameter estimation problem to estimate a vector consisting of the GPS altitude bias and time offset in addition to the camera yaw, pitch and roll biases. We then develop a special maximum likelihood estimator using the Iterated Least Squares algorithm which can work with a non-synchronized time-discrete GPS trajectory for the third challenge. Since the camera measurement errors are usually small, this requires a high calibration accuracy so that the residual bias error following the calibration should not be significant compared to the measurement error standard deviation. The calibration accuracy depends highly on the drone trajectory. This paper also recommends an appropriate drone trajectory which can yield a good calibration accuracy, namely, 14\% of the measurement error standard deviation. Simulation tests are conducted to demonstrate the algorithm performance. The estimation results meet the Cramer-Rao Lower Bound (CRLB) since the Normalized Estimation Error Squared w.r.t.\ the CRLB is statistically acceptable.

0.18

Payload Swing Estimation and Damping Without Payload Parameters for Multirotor UAVs

eess.SY cs.RO ·2026-08-19 ·K. Taki, K. Umemoto
similarity 0.57
Abstract

Cable-suspended payload transport by multirotor UAVs is flexible but generates periodic swing disturbance that degrades tracking and risks instability. Existing anti-swing methods require additional sensors or precise identification of cable length and payload mass, limiting field deployment. We propose a swing-estimation and damping method using only the onboard IMU and throttle command, requiring no payload parameters. An extended Kalman filter extracts the periodic disturbance with the unknown pendulum frequency as an estimated state, and an active damping controller adds a correction angle to the attitude loop to dissipate pendulum energy. Flight experiments confirm robust damping across a tested range of cable-length and mass variations.

0.21

Compact Force Sensor for Dual-UAV Cable-Suspended Payload Transport with Tension-Aware Outer-Loop Control

cs.RO ·2026-09-25 ·Andrea Delbene, Giorgio Cannata, Giorgio Carlini, Filippo Sante, Marco Baglietto
top venue similarity 0.55
Abstract · Preprint version for IEEE Robotics and Automation Letters, link to article: https://ieeexplore.ieee.org/document/11743837

Cooperative payload transportation using multiple Unmanned Aerial Vehicles (UAVs) poses challenges in stability, coordination, and robustness, especially under external disturbances and unmodeled dynamics. This work proposes a dual-UAV payload transportation framework supported by a compact, custom-designed force sensor measuring the interaction force at the UAV cable anchor point. The sensor design and mathematical model are presented, and its performance is characterized through static and dynamic tests evaluating linearity, hysteresis, repeatability, and crossload. The control architecture follows a cascade structure: fast inner loops handle vehicle stabilization, while outer loops are designed to compensate for the measured forces. The approach is validated through simulations and indoor experiments under position uncertainty. Payload-drop and constrained-space tests assess the proposed sensing and control architecture against literature-based distributed references, showing improved stabilization, coordination, and disturbance rejection. A video of the experiments is available at: https://youtu.be/rIw9-fvV8Qw.

0.47

Cooperative Aerial Transportation of a Payload with a Sliding Cable Attachment

cs.RO cs.MA ·2026-10-09 ·Sebastian Tilaguy Lezama, Diego S D'Antonio
similarity 0.54
Abstract

This paper presents a dual-quadrotor hook- suspended transport system for cooperative aerial manipulation of a payload that is not rigidly attached to a fixed point along the cable. Two quadrotors are connected by a single inextensible cable that passes through a frictionless hook mounted on the payload, allowing the cable to slide between its two segments. This introduces a cable-distribution variable that couples the quadrotor motion, cable geometry, and payload dynamics. A feasible reference-generation framework is formulated using the desired payload pose, cable distribution, and system shape while satisfying the cable-length constraint and elliptical workspace. The quadrotors track the geometrically generated trajectories while maintaining positive cable tension and respecting actuator limits. The payload pose is estimated from the system geometry, and its measured position is used only to validate the desired trajectory. The approach is evaluated through experimental demonstrations.

0.33

Dynamic Modeling and LQR Control of a Single Coaxial Drone with 2DOF Thrust Vectoring Mechanism

cs.RO eess.SY ·2026-09-17 ·Ali Jokar, Amin Talaeizadeh, Aria Alasty
similarity 0.54
Abstract

Coaxial rotor drones have generated considerable interest because of energy efficiency and small size, but they are afflicted with inherent underactuation for roll and pitch control, although systems like swashplates have circumvented this limitation at the cost of greater mechanical complexity. This work presents a novel coaxial drone supplemented by a two-degreesof-freedom pendulum mechanism for active thrust vectoring that offers a less mechanically complicated alternative. We develop a comprehensive Lagrangian dynamic model that does not ignore the inertial contributions of all the components, including body, servo arms, and motor assembly. A Linear Quadratic Regulator(LQR) is designed based on the linearized dynamics around the hover equilibrium. High-fidelity simulations taking actuator dynamics and sensor noise into account validate the proposed architecture. An Extended Kalman Filter (EKF) blends GPS, barometer, and IMU estimates with high accuracy for state estimation. The findings verify the potential and reliability of this approach for power-saving, rapid coaxial UAVs.

0.13