CS Paper Radar

A Personalized Dynamic Balance Evaluation Paradigm for Hip Exoskeleton-Assisted Walking under Unexpected Ground Perturbations

Yun Chen, Oluwasegun T. Akinniyi, Qiang Zhang

cs.RO cs.LGeess.SY ·submitted 2026-09-13 19:56 UTC · v1
published

Abstract

Hip exoskeletons may improve recovery from unexpected gait perturbations, yet personalizing assistance remains difficult because balance is multidimensional and human-in-the-loop experiments are small-sample and noisy. We present a participant-specific composite balance cost that integrates seven biomechanical sub-metrics spanning margin of stability, center-of-mass dynamics, and whole-body angular momentum. The sub-metrics are converted to direction-aligned, dimensionless cost features, and nonnegative fusion weights are learned on the simplex. Coupled with an empirical-Bayes hierarchical model, the learned-composite selector estimates each tested condition's posterior probability of being best, P(best), and a high-probability candidate set with size $K_{0.8}$. The framework was evaluated with three participants walking at 1.1 m/s during unilateral belt-slip perturbations across 46 hip-assistance conditions. In the full-budget analysis (B = 4 repeats per condition), the selector concentrated 80% of the posterior probability within 1 to 5 of 46 conditions, compared with 2 to 12 for equal-weight fusion and 4 to 37 for principal component analysis fusion. This smaller candidate set could shorten personalization experiments and limit participants' exposure to repeated perturbations in future studies. Selected-condition trials showed lower observed composite costs than no-torque trials, with nominal p < 0.05 for P2 and P3. Leave-one-repeat-out refits yielded positive mean held-out rank correlations for all participants and moderate stability of the learned weights and candidate sets. These proof-of-concept results support participant-specific composite balance evaluation for candidate selection in perturbation-based human-in-the-loop experiments.

Comment
8 pages, 6 figures. Accepted to the 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

Closest papers

Nearest neighbours by meaning across the whole index.

Learning a Speed-adaptive Hip Exoskeleton Control Policy Via Sim-to-real Reinforcement Learning

cs.RO ·2026-09-23 ·Bin Li, Zhimin Hou, Jiacheng Hou, Zenian Liang, Tong Wu +2 more
similarity 0.69
Abstract

Providing personalized exoskeleton assistance across varying walking speeds remains challenging. Existing online optimization methods are sample-inefficient, requiring extensive human-in-the-loop (HIL) evaluations to optimize the entire assistive torque profile. Sim-to-real reinforcement learning (RL) offers a promising alternative but cannot directly account for individual user preferences. We propose a framework integrating sim-to-real RL with online preference learning for personalized exoskeleton assistance. Specifically, assistance timing is learned in simulation by training RL policies with human musculoskeletal models across varying walking speeds. The learned policies are then distilled and deployed on a physical hip exoskeleton using onboard sensory observations. Gaussian-process-based preference learning further personalizes the assistance magnitude through pairwise user comparisons. By decoupling assistance timing learning in simulation from magnitude optimization in real-world experiments, our framework substantially reduces the online optimization space. Human-subject experiments demonstrate efficient identification of personalized assistive torque profiles across varying walking speeds with fewer real-world evaluations.

0.14

Context-Continuous Preference Learning for Exoskeleton Personalization

cs.LG cs.RO ·2026-09-23 ·Sunin Baek, Sungwoo Park, Daekyum Kim
similarity 0.66
Abstract · 23 pages, 11 figures, including supplementary materials

Personalizing exoskeleton assistance across operating conditions is constrained by the time and physical effort required to collect user feedback. We examined whether a user's preference landscape varies smoothly across operating conditions and when this continuity supports learning from limited feedback. We propose Context-Continuous Preference Learning (CCPL), a Gaussian-process preference model that shares observations across nearby contexts while retaining context-specific utility estimates. We evaluated CCPL through simulations and retrospective analyses of ankle and elbow exoskeleton preference data from nine healthy adults. In simulations, CCPL improved reconstruction and preference-based Bayesian optimization relative to independent learning when preferences varied smoothly, but showed negative transfer when continuity was weak. In both human studies, full-data reference landscapes estimated separately for each participant and context tended to be more similar between nearby operating conditions. With five exposures per context, CCPL increased mean reconstruction correlation with these references from 0.644 to 0.720 for ankle assistance and from 0.476 to 0.526 for elbow assistance relative to independent learning. The five-exposure budget was approximately 37% lower for ankle and 17% lower for elbow than the estimated independent-learning budgets needed to match these correlations. CCPL also improved held-out response prediction relative to independent learning, while benefits over pooled learning varied. These findings support context continuity as a basis for sharing preference observations under limited feedback, although benefits for online personalization in humans remain to be established.

0.29

Subject-Specific Predictive Musculoskeletal Simulations of Lower-Limb Exoskeleton Assistance: Metabolic and Biomechanical Effects of Joint Assistance Strategies

cs.RO ·2026-10-02 ·Neethan Ratnakumar, Mariya Tohfafarosh, Xianlian Zhou
similarity 0.65
Abstract

Lower-limb exoskeletons have made considerable progress in reducing energy expenditure during walking. However, designing optimal assistance strategies remains challenging, particularly given inter-individual variability in anthropometry and biomechanics. This study explores energy-optimal lower-limb joint-assistance strategies using predictive simulations with musculoskeletal models. Subject-specific models of six able-bodied subjects, with BMI-based muscle strength scaling, were used in predictive simulations to generate gait at self-selected walking speeds. Ideal actuators were incorporated to simulate various combinations of joint assistance at peak levels of 25 Nm and 50 Nm to examine the effects of assistance on gait and metabolic savings. The effects of each assistance configuration were assessed through cost of transport (COT), joint kinematics, muscle activations, assistive torques, and joint-level power metrics to characterize the biomechanical and energetic impacts of different assistance strategies. At 50 Nm, combined H+K+A (hip-knee-ankle) assistance resulted in the greatest mean COT reduction of 48.50 +/- 4.55%, with individual reductions ranging from 42.22% to 54.65% across the subjects. Among single-joint conditions, assisting the hip was most effective, reducing COT by 31.77 +/- 5.21%; the knee and ankle produced smaller, comparable reductions (19.17% and 17.02%). H+A (hip-ankle) assistance (44.60 +/- 7.08%) emerged as the most effective two-joint assistive configuration. Increasing the torque bound increased positive assistive power primarily at the hip and ankle, while knee assistance showed little sensitivity and delivered positive power near pre-swing. These results support H+A assistance as an efficient two-actuator target, while identifying the knee's atypical pre-swing power strategy as a candidate for targeted experimental validation.

0.14

Multi-Agent Reinforcement Learning of Co-Adaptive Hip Exoskeleton Control (MARL-Exo) for Metabolic Energy Reduction

cs.RO cs.LG ·2026-10-27 ·Yifei Yuan, Jakob Wolf, Ghaith Androwis, Xianlian Zhou
similarity 0.64
Abstract · 14 pages, 6 figures, including supplementary material

Objective: This study aims to determine whether a hip-exoskeleton policy trained in simulation, by co-adapting with a musculoskeletal human model under a metabolic-energy reward, reduces the metabolic cost of walking in new users without per-user tuning, and how mechanical-power shaping affects the learned assistance. Methods: We developed MARL-Exo, a multi-agent reinforcement learning framework in which a full-body human model (304 muscle actuators; randomized anatomy, gait, and speed) and a bilateral hip-exoskeleton policy are trained concurrently in two stages. The exoskeleton observes only delayed hip kinematics and its past commands; its reward includes muscle metabolic power from a physiologically based energetics model, alone (Metabolic) or with mechanical-power shaping (Metabolic + Power). The Metabolic policy was deployed and tested without retraining in eight healthy adults walking at 1.25 m/s, using indirect calorimetry. Results: In simulation, the Metabolic policy reduced modeled muscle metabolic power by 13.8% relative to no-device walking, versus 8.8% for Metabolic + Power. On hardware, MARL-Exo reduced net metabolic rate by 18.3 $\pm$ 6.6% relative to Passive in all eight participants. Relative to No-Exo, the mean reduction was 7.4 $\pm$ 10.0%; six participants more than offset the 13.1% device-wearing penalty, walking up to 24.2% below their No-Exo cost. Conclusion: A metabolically informed policy co-adapted in simulation transferred to users without per-user tuning and consistently reduced the metabolic cost of walking with the device, while explicit power shaping reduced the simulated benefit. Significance: Unlike per-user human-in-the-loop optimization, this approach yields a single population-level controller and allows assistance objectives to be screened in simulation before human testing.

0.29

UniExo: Unified Multi-Skill Policies for Musculoskeletal Locomotion and Co-Adaptive Exoskeleton Control

cs.RO cs.LG ·2026-09-17 ·Yifei Yuan, Jakob Wolf, Ghaith Androwis, Xianlian Zhou
similarity 0.64
Abstract · 9 pages, 8 figures

Daily locomotion encompasses diverse activities and frequent transitions between them, yet most exoskeleton controllers are designed for a single activity or a narrow set of related movements. Changes in activity therefore typically require explicit mode switching and separately tuned or retrained controllers. Simulation-based learning reduces the need for hardware-based tuning but generally retains this limitation. Here we present UniExo, a framework that first constructs a multi-skill musculoskeletal human policy and then jointly trains an exoskeleton control policy with it. Four single-skill imitation experts for walking, turning, running and backward walking are distilled into a single network structured by a skill latent and subsequently fine-tuned through reinforcement learning on transition sequences. The resultant unified human policy achieves a mean tracking success rate of 94.7% on unseen clips of the four skills and exhibits greater robustness to perturbations than its constituent experts. A single hip exoskeleton controller (UniExo) is initialized from hip moment prediction of the human policy and co-adapted with it through multi-agent reinforcement learning across the four skills. This co-adaptation shifts the timing of the assistance torque and raises the fraction of positive work delivered to the hip. When deployed on a custom hip exoskeleton, the controller generalizes across four treadmill speeds in six participants and assists one participant through a continuous route of all four skills and their transitions, without skill labels or explicit mode switching. UniExo thus provides a step towards replacing activity-specific controllers with unified, user-specific controllers that support diverse locomotor activities and the transitions between them.

0.32

Personalized Lower-limb Exoskeleton Assistance via Preference-based Bayesian Optimization

cs.RO ·2026-08-10 ·Xiao-Yin Liu, Guotao Li, Weiqun Wang, Zeng-Guang Hou
similarity 0.64
Abstract · 20 pages, 15 figures, https://youtu.be/8X1SFqUU4G4

A significant challenge in exoskeleton robotics is the need to dynamically adapt control profiles to individual motion preferences, thereby ensuring both efficient and comfortable assistance. Currently, since user experience can serve as a comprehensive metric for evaluating the effectiveness of assistance, user preference-based optimization methods have been widely studied for parameter tuning. However, the existing methods rely heavily on extensive human-robot online interactions and suffer from slow optimization speed, which not only induces user fatigue but also compromises optimization effectiveness. Therefore, this paper aims to explore an efficient preference-based optimization framework for personalized exoskeleton assistance that can learn optimal parameters with minimal interaction. We propose a preference-based Bayesian optimization (PbBO) approach that can improve sample efficiency by leveraging knowledge about the sampling distribution of candidate sets. For optimizing six control parameters, PbBO can converge to user-preferred parameters with 90.7% validation accuracy via 20 iterations. Moreover, the hierarchical controller is designed to generate personalized torque for different tasks and achieve interaction torque tracking in real time. The results of treadmill and outdoor experiments demonstrate that the optimized parameters can reduce metabolic rate by 14.5%-15.4%, heart rate by 6.3%-7.6%, and muscle activation by 6.7%-31.5% compared to unassisted walking.

0.56

Continuous Lower-Limb Joint-Angle Estimation from sEMG and IMU: The Conditional Value of Cross-Activity and Cross-Subject Data under Update-Matched Controls

cs.RO cs.LGeess.SP ·2026-11-14 ·Jiaying Xu, Guangyuan Chen, Buyun Gao, Zhen Dong
similarity 0.63
Abstract · 8 pages, 5 figures, 3 tables. Submitted to IEEE Robotics and Automation Letters (RA-L)

Intent-driven exoskeleton control needs a continuous, causal estimate of the wearer's joint kinematics and an answer to a second question: whose data should train the estimator for a new user? Borrowing the user's recordings of other activities, or other users' recordings of the same activity, is usually evaluated as "more data" versus "less data," which confounds the information a source carries with the optimizer updates it adds and hides negative transfer behind averages. We separate these effects for hip, knee, and ankle angle estimation from high-density sEMG and an IMU across six locomotion activities on all ten participants of a public dataset. A compact residual causal TCN-GRU decoder is frozen, and an update-matched replay control prices every added source against the same number of updates on the user's own data. A user's own other activities raise $R^2$ from 0.722 to 0.788, of which +0.048 is information beyond replay; stair descent is a reliably harmful donor and sit-stand-walk a reliably beneficial one. Other users' same-activity data help while the user has only the target activity ($G_\mathrm{T} = +0.053$) and half as much once own other-activity data exist ($G_\mathrm{W} = +0.028$); at full calibration, donor value collapses after one to two target records. Per-target gains from the two sources correlate, and leave-one-participant-out gates recover most of the cross-subject value only at low calibration. Data value is hierarchical, state-dependent, and directional; the bottleneck is deciding, without test labels, when to transfer.

0.23

Multi-Objective Human-in-the-Loop Bayesian Optimization of a Lower-Limb Exoskeleton

cs.RO cs.HC ·2026-09-25 ·Neil Janwani, Matthew T. Lerner, Aaron J. Young, Maegan Tucker
code/data similarity 0.61
Abstract

Human-in-the-loop optimization (HILO) is a common approach for optimizing the control of assistive devices to account for the wearer's unique biomechanics and subjective preferences. However, despite research suggesting that a person may have a different prioritization of objectives depending on time-varying factors such as the environment, their mood, or energy levels, existing HILO approaches only consider a single objective or enforce a fixed weighting on a set of objectives. Neither approach is capable of representing an individual's preferences over objectives. In this work, we propose Multi-Objective Human-in-the-loop Bayesian Optimization (MO-HILBO), which builds on explicit multi-objective Bayesian optimization to efficiently infer a personalized set of Pareto-optimal controllers. We compare our approach with an existing multi-objective HILO method and experimentally demonstrate MO-HILBO on a lower-limb exoskeleton across two objectives: metabolic cost (efficiency) and ordinal human feedback (comfort). We find that MO-HILBO (1) discovers Pareto-optimal controllers, and (2) that the pairwise ordering of points on the Pareto front itself is consistent with validation trials. Lastly, we open-source mohilo, a Python package for running both HILO and MO-HILBO on wearable devices: https://dynamicmobility.github.io/mohilo/.

0.32