CS Paper Radar

Coupled State-Space Modelling, Control, and Policy Distillation for Hybrid Rigid-Pneumatic Manipulators

Alan Royce Gabriel Samuel, Pulkit Verma

cs.RO ·submitted 2026-09-24 11:45 UTC · v1
published

Abstract

Hybrid manipulators combine motorized rigid joints with pressure-actuated origami segments. Published arms of this kind are controlled with decoupled per-DOF loops, and the cost of this approximation has not been quantified, because the coupled model needed to measure it has not been built. This paper derives such a model for a chain of $N$ alternating revolute joints and Kresling origami segments, including pneumatic chamber dynamics and crease hysteresis. Using the model, we measure the coupling directly and show that its strength varies joint by joint, and that decoupled control loses precisely on the strongly coupled joints while remaining competitive on the one nearly decoupled joint. Coupled model-based controllers track $2.5\times$ tighter than a decoupled PID baseline at lower torque. However, the model predictive controller (MPC) is too slow for real time, and model-free reinforcement learning stalls far below acceptable success rates on a strict settling metric. We therefore distill the MPC into a small neural policy with behavior cloning and DAgger. The distilled policy settles 93-94$\%$ of goals with zero collisions, within a few points of its teacher, and runs inside the 5 ms control step where the MPC does not. Where the teacher itself fails, we trace the failure to a limit cycle with the bellows' lightly damped mode, and we remove it by selecting goal postures holdable at low pressure.

Comment
8 pages, 4 figures, ICRA

Closest papers

Nearest neighbours by meaning across the whole index.

A Task-Agnostic Control Strategy for Dynamic Assistance with Pneumatically Actuated Soft Exosuits

cs.RO cs.HC ·2026-08-18 ·Anoush Sepehri, Zachary Huang, Raymond de Callafon, Michael T. Tolley, Tania K. Morimoto
similarity 0.58
Abstract

Pneumatic artificial muscles have provided new opportunities to develop upper-extremity soft exosuits for reha- bilitation, augmentation, and assisted daily living. However, the complex dynamics and limited bandwidth of these actuators has made providing responsive assistance based on user intention a longstanding challenge. In this work, we present an inverse-plant control strategy for pneumatically actuated soft exosuits that only relies on kinematic sensing for task-agnostic and dynamic assistance during daily living. We model the human-robot system using a Hammerstein dynamic model, consisting of a Preisach hysteresis model and a linear time-invariant filter, to capture the static and dynamic behavior of the system. We personalize our model to each user using 140 s of data and approximate an inverse to integrate into our control loop. When evaluated on a test rig that emulated a soft assistive exosuit for the wrist, our controller reduced the interaction torque by up to 73% and the activation of key flexor and extensor muscles by up to 47% relative to the condition with no assistance for speeds ranging from 8°/s to 120°/s. Overall, this work presents a control strategy that can provide task-agnostic, dynamic assistance with pneumatically actuated soft exosuits without the need for physiological or force sensors to interpret user intention.

0.19

Control-Oriented Learning for Dynamic Tracking and Stability Analysis of Soft Pneumatic Actuators

cs.RO ·2026-08-25 ·Nithin S. Kumar, Eric J. Barth
similarity 0.58
Abstract · 8 pages, 10 figures

Soft pneumatic actuators offer inherent compliance and safe interaction but remain difficult to model and control because of their highly nonlinear, distributed dynamics. We present a control-oriented data-driven modeling and control framework that decomposes actuator behavior into a nonlinear static equilibrium model and a linear residual dynamics model identified using Extended Dynamic Mode Decomposition with control (EDMDc). This representation enables feedforward compensation, task-space feedback control, and local closed-loop stability analysis through an augmented linear model. Experiments achieve approximately 1 mm root mean square error (RMSE) during low-speed (approximately 10 mm/s) trajectory tracking and below 10 mm RMSE at higher speeds (approximately 100 mm/s). The framework further achieves stable tracking of highly dynamic user-generated references with peak accelerations exceeding 25 m/s^2 while simultaneously performing real-time obstacle avoidance. Finally, the proposed stability analysis is experimentally validated by accurately predicting stable, marginal, and unstable operating regimes. These results demonstrate that structured, control-oriented learning provides an accurate and practical framework for soft actuator control.

0.37

DUET: Decoupled Upper- and Lower-Body Execution for Task-Agnostic Humanoid Loco-Manipulation

cs.RO cs.LG ·2026-09-19 ·Kapalik Khanal, Biswash Khatiwada, Stephen Afrifa, Fan Wu, Ramesh Bahadur Bist
similarity 0.57
Abstract

Changing a humanoid robot's manipulation policy should not require retraining the controller that maintains the robot's balance. This study introduces DUET, a decoupled execution framework that enables locomotion and manipulation controllers to operate simultaneously by combining their commands only at the robot interface. A reinforcement-learning locomotion policy controls the 12 leg joints and a waist yaw joint, tracking planar velocity, turning rate, and pelvis height from deep crouching to upright standing on a 23-degree-of-freedom Unitree G1. The 10 arm joints are excluded from the action space, while their positions and velocities are included only as observations, so that any compatible manipulation policy that generates arm-joint targets can control the upper body, and the locomotion policy keeps the lower body stable without requiring shared training or direct coordination. This study demonstrates the modular approach on hardware by pairing the same locomotion checkpoint with two different vision-language-action models, GR00T N1.7 and pi0.5. In simulation evaluation, the locomotion controller kept the robot's lower body stable with no falls while tracking the commanded planar velocity, yaw rate, and pelvis height with errors of 0.186 m/s, 0.142 rad/s, and 0.016 m, respectively. Ablation studies identify the upper-body pose curriculum as the dominant component, and removing this training step reduces episode survival from 20.0 to 7.4 seconds and increases the fall rate to 6.06 per environment minute. Robustness tests show no falls under pushes of up to 1.0 m/s within the trained payload range, and no falls at twice the payload limit for pushes below 0.7 m/s. These results show that a manipulation policy can be exchanged without retraining, restarting, or otherwise touching the layer that keeps the robot upright.

0.22

Task-space model-based control of pneumatic soft actuators

cs.RO ·2026-08-27 ·Nithin S. Kumar, Joshua Gaston, D. Caleb Rucker, Eric J. Barth
top venue similarity 0.57
Abstract · 11 pages, 14 figures

Soft actuators enable dexterous and compliant interaction, but closed-loop task-space control remains challenging due to strong nonlinearities, distributed deformation, and uncertainty in their dynamics. This paper presents a real-time dynamic-model-based task-space feedback and estimation framework based on a non-minimal coordinate discrete elastic rod model formulated in absolute coordinates with holonomic constraints. The resulting structure preserves distributed mechanics while maintaining computational efficiency through sparse system matrices, enabling real-time control with up to 10 discretized rods. A quasi-static feedforward inverse model is combined with a task-space PI controller and a dynamic observer that fuses measurement residuals as virtual forces, enabling full-state estimation from sparse sensing. The approach is experimentally validated on three planar pneumatic soft actuators with varying geometries. Across five tasks, including drawing the digits 0-9 across the workspace (3-18 mm/s tip speed), tracking periodic motion (up to 37 cm/s), cross-platform generalization, reduced sensing conditions, and real-time user-defined references, our method achieves 1.5-2.3 mm root mean square error (RMSE) for precision motions and 5.5-12.4 mm RMSE at 1-2 Hz. Results demonstrate that structured, non-minimal dynamic models can enable real-time, high-precision, moderate-bandwidth task-space control of planar soft pneumatic actuators in free space.

0.27

Online iLQR-MPC with Whole-Body Control for Robust Humanoid Locomotion

cs.RO ·2026-11-03 ·Xiang Li, Linlin Ou, Ruihan Wu, Xinyi Yu
similarity 0.56
Abstract

Humanoid locomotion requires deciding where to step and how to distribute contact forces. However, a disturbance can invalidate the nominal plan, requiring coordinated revision under constraints that switch with every footfall. To solve this online, the proposed approach employs the single-rigid-body model, which retains attitude dynamics and the full contact wrench. An iterative linear-quadratic-regulator MPC (iLQR-MPC) then jointly optimizes contact forces and footstep locations in a single receding-horizon problem, without a separate step planner. Specifically, contact and motion constraints are incorporated into the backward pass through augmented-Lagrangian and relaxed-barrier penalties. A whole-body controller subsequently maps the plan to joint torques at 500 Hz while preserving contact feasibility. The model-based formulation makes disturbance responses interpretable through explicit costs and constraints, and requires no platform-specific policy training. In MuJoCo simulations, the iLQR-MPC replans at 100 Hz (mean solve time 8.9 ms); the Unitree G1 sustains steady-state walking and recovers from impulsive 245 N forward and 175 N lateral pushes.

0.18

Port-Hamiltonian Koopman Operator Synthesis for Mechanical Systems

cs.RO eess.SY ·2026-09-15 ·Rajpal Singh, Aditya Singh, Jishnu Keshavan
similarity 0.56
Abstract

Finite-dimensional Koopman models enable efficient linear prediction and control of nonlinear robotic systems. However, models learned purely from trajectory data may violate the energetic structure of the underlying mechanics, producing predictions that exhibit artificial energy growth and diverge under recursive propagation. This work presents a structure-preserving Koopman framework for Euler-Lagrange systems built on generalized-momentum coordinates. The momentum transformation exposes the mechanical actuation as a known, state-independent port, which is preserved explicitly in the lifted dynamics. A structure-constrained neural architecture is developed to jointly learn the lifting functions and a port-Hamiltonian Koopman generator, rendering the learned dynamics passive by construction rather than through penalty terms or post-hoc projection. A Cayley-midpoint discretization further preserves the corresponding storage-dissipation balance exactly in discrete time. These properties are established analytically by deriving the discrete storage balance and associated stability guarantees of the learned predictor. Simulation and experimental studies demonstrate improved prediction accuracy, data efficiency, and closed-loop tracking over Koopman baselines, with increasing gains for higher-dimensional systems.

0.23

Contact-Rich Robotic Manipulation in Construction via Zero-Shot Learning: A Diffusion Policy-Guided Adaptive Control

cs.RO ·2026-08-22 ·Roman Ibrahimov, Salma Mozaffari, Arash Adel
benchmark similarity 0.56
Abstract

Construction robotics and automation offer promising means of improving productivity, alleviating workforce shortages, and reducing workers' exposure to physically demanding tasks. However, reliable contact-rich robotic assembly remains challenging under tight tolerances, fabrication inaccuracies, and uncertain contact dynamics. To address this challenge, we present a framework coupling diffusion policies trained on simulation-generated pose and force/torque data with an L1-inspired adaptive controller that corrects policy-predicted actions online to compensate for unmodeled contact dynamics. We benchmark the framework against baselines in timber joinery, pipe fitting, and sequential full-scale truss assembly. It achieves 100% success on single-task assemblies and 90-100% success across sequential truss assembly subtasks, with lower, more stable contact forces than the baselines. By enabling zero-shot sim-to-real transfer for force-aware contact-rich assembly, the framework reduces costly, labor-intensive real-world data collection for policy training and advances scalable, robust automation of multistage assembly, motivating extension to broader contact-rich manipulation tasks in construction.

0.23

Learning the Dynamics of Deformable Linear Objects Through Coupled Oscillators for Bimanual Robotic Manipulation

cs.RO ·2026-11-17 ·Iván López-Broceño, Maximilian Stölzle, Daniel Feliu-Talegon, Daniela Rus, Cosimo Della Santina
similarity 0.55
Abstract

Many learning-based approaches for deformable linear objects (DLOs) rely on simplified deformation models that neglect dynamic effects and the mechanical response of the objects, limiting their applicability to lightweight, compliant objects and slow motions. Inspired by recent advances in learning physically structured dynamics with coupled oscillator networks (CONs), we propose $Φ$-CON for learning force-driven DLO dynamics. The model combines a floating-base coupled oscillator network (FBCON), whose latent potential energy depends only on the DLO's shape, with a learned affine diffeomorphism $Φ$ between observed positions along the DLO and latent coordinates. Its shape dynamics are stable by construction, and its Lagrangian structure yields explicit expressions for kinetic and potential energy. We exploit this structure to design a model-based proportional-derivative (PD) controller that compensates for the learned potential forces, thereby establishing closed-loop stability guarantees and ensuring convergence. We evaluate the approach on four simulated DLOs and a real bimanual robot setup. In simulation, $Φ$-CON achieves prediction accuracy comparable to neural ordinary differential equation (NODE) models and Lagrangian neural networks (LNNs), with $97.2\%$ and $90.2\%$ fewer parameters, respectively. Relative to a model-free PD baseline, the proposed controller reduces mean endpoint regulation error by $97.5$-$99.7\%$ in simulation and achieves a mean per-target reduction of $27.9\%$ across both endpoints in real-world experiments, demonstrating the importance of explicitly accounting for the mechanical response of stiff and heavy objects.

0.24