CS Paper Radar

Enhancing Energy Harvesting in Harmonically Forced Oscillators via Regenerative Impulsive Braking

Nilay Kant

eess.SY ·submitted 2026-10-06 15:02 UTC · v1
unusual

Abstract

This paper investigates whether regenerative impulsive braking can enhance passive energy harvesting in harmonically forced oscillators. An impulsive braking event directly extracts kinetic energy while simultaneously inducing a transient that alters subsequent passive harvesting. The analysis shows that suitably timed braking can produce a net energy gain over passive harvesting alone. The braking-induced transient is derived analytically and used to obtain an exact expression for the harvested-energy gain over an arbitrary finite post-braking horizon, together with conditions for positive gain and the optimal braking instant. The corresponding infinite-horizon analysis shows that optimal braking occurs at zero crossings of the harmonic excitation, with complete braking maximizing the gain. Numerical results further show that the finite-horizon harvested-energy gain can exceed its infinite-horizon value. Simulations using short-duration high-gain braking closely match analysis, supporting potential of the proposed approach for energy-harvesting applications.

Closest papers

Nearest neighbours by meaning across the whole index.

Electric Racing Kart with BLDC Drive, LiFePO4 Battery System, Traction Control and Regenerative Braking

eess.SY ·2026-10-06 ·Johannes Stockhammer, Tom Rettenwander, Philipp Huber
publishedunusual similarity 0.49
Abstract · German title: Elektro-Rennkart mit BLDC-Antrieb, LiFePO4-Batteriesystem, Antischlupfregelung und Rekuperation. Diploma thesis, HTL Braunau, …

This diploma thesis documents the conversion of a petrol-powered go-kart into a battery-electric kart with a 10 kW BLDC drive, a LiFePO$_4$ traction battery with battery management system, a slip-based traction control and regenerative braking. The traction control estimates the slip of the driven rear axle from three Hall-effect wheel-speed sensors as $λ= (v_R - v_F)/v_R$ and reduces the torque command of the throttle pedal when the axle slips. It runs on a 32-bit ARM Cortex-M3 microcontroller (SAM3X8E) in the signal path between pedal and motor controller, with galvanic isolation and an emergency stop. Regenerative braking uses the generator mode of the motor controller in three stages: motor brake on throttle release, light braking via a steering-wheel button, and blended braking with the hydraulic brake. Drivetrain calculations show that the kart is traction-limited. At rated torque, the drive force at standstill exceeds the transmissible traction force by a factor of 1.7 to 2.0, up to approx. 27 to 43 km/h. Traction control is therefore a functional requirement of the drivetrain. The calculated top speed is approx. 65 km/h. Regenerative braking reaches approx. 0.45 g and could cover up to about 30 % of the energy demand on a winding track. With 80 % of the nominal battery energy, approx. 44 min of driving at 50 % motor load result, so the target of one hour is missed. The initial charging measurement quantifies the flat LiFePO$_4$ voltage plateau at 0.7 to 1.8 mV per percent state of charge, which makes voltage-based state-of-charge estimation unreliable. Cold cells showed a voltage sag under load that triggered the low-voltage alarm. Validation of the control functions by instrumented driving tests is the main open point.

0.38

Energy-Aware Path Following: Comparative Analysis of Reinforcement Learning and NMPC for Electric Vehicles

cs.RO cs.LGeess.SY ·2026-10-06 ·Mohamed Sabaa, Mostafa Emam
similarity 0.46
Abstract · 20 pages, 12 figures, currently submitted for review at the journal (Robotics and Autonomous Systems) https://www.sciencedirect.com/journal/…

Path-following control strategies typically follow the bi-objective optimization dilemma: minimizing deviations from a reference path while maintaining smooth speed profiles. The latter objective is especially relevant for Electric Vehicles (EVs), since their limited driving range can be extended by recovering energy through regenerative braking, a feature that has not yet been sufficiently studied in the literature. In this work, we perform a comparative analysis of four controllers under one common Frenet frame-based kinematic vehicle model, utilizing a validated energy model (VT-CPEM) with explicit regenerative braking. Herein, we implement the following controllers: Nonlinear Model Predictive Control (NMPC), Proximal Policy Optimization (PPO), gain-scheduled Ackermann state-feedback baseline (PID-SF), and a Stanley geometric baseline. To satisfy real-time requirements, we implement the NMPC using JIT-compiled CasADi. Moreover, we train the PPO using traditional straight and S-curve tracks, after which we successfully transfer the unmodified policy to unseen tracks, including: an ISO 3888-1 lane-change, a chicane, randomly-generated parameterized-splines, and a $\pm3^\circ$ graded road. In addition, the policy transfers to a dynamic single-track vehicle model with linear tires, zero-shot with an acceptable initial performance, which was optimized after brief fine-tuning. Thereby, we demonstrate that our PPO is readily transferable to more comprehensive vehicle models. We conclude with a performance analysis of developed controllers and discuss ideas for future work.

0.25

Piezoelectric Energy Harvesting from a Pitch-Plunge Aerofoil in Compressible Flow, the Euler Full-Order Model, Strip Theory and the Reduced Models Compared

cs.CE ·2026-09-16 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
similarity 0.43
Abstract · 15 pages, 4 figures

A piezoelectric transducer embedded in a pitch-plunge aerofoil with a finite-mass trailingedge flap converts the limit-cycle oscillation that follows flutter into electrical power. The design findings for such a harvester have so far been obtained with incompressible strip theory, whose aerodynamic state is a handful of lag variables. Here the same section, the same transducer and the same test cases are coupled instead to the two-dimensional compressible Euler equations, giving a full-order model of twelve thousand states, and the two aerodynamic models are placed side by side on the flutter boundary, on the limit cycle and on the harvested power, with the strip-theory results compared against higher fidelity aerodynamic modelling provided by CFD. The degree of freedom carrying the transducer remains the first-order design variable, and the ranking of the mountings and the position of the optimum in the coupling and load-resistance plane are unchanged, while strip theory is found to underpredict the harvested power of the compressible section and to overstate the effect of the transducer on stability where the electrical time constant meets the flutter frequency. A nonlinear reduced model of four states, built on eigenvectors of the coupled Jacobian at the velocity of interest, reproduces the frequency of the cycle, its pitch amplitude, the transducer voltage and the mean power, and misstates the proportion of plunge to pitch in the orbit and its phase. That error is shown to be independent of the amplitude of the cycle and to survive enlargement of the basis, which places it in the retained subspace rather than in the order of the expansion, and suggests that such models should be judged on the shape of the orbit rather than on a single amplitude.

0.37

Optimal energy conversion -- A port-Hamiltonian approach

eess.SY ·2026-10-15 ·Guanru Pan, Karl Worthmann, Manuel Schaller, Timm Faulwasser
similarity 0.42
Abstract

This paper studies optimal energy conversion in port-Hamiltonian systems. We analyze state- and control-constrained finite-horizon optimal control problems that maximize energy conversion efficiencies. Under suitable reachability conditions, we show that the asymptotic optimal efficiencies exist and coincide with the corresponding optimal cyclic efficiencies. For a class of port-Hamiltonian systems describing coupled storage-conversion components, we further derive intrinsic limits on achievable energy conversion and establish a generalized Carnot-type efficiency bound. Our results provide an optimal-control framework connecting asymptotic optimal operation, cyclic operation, and fundamental efficiency limits for port-Hamiltonian systems.

0.20

Rigid-body support motion and post-flutter piezoelectric energy harvesting from a pitch-plunge-flap aerofoil

cs.CE ·2026-09-21 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
similarity 0.40
Abstract

A piezoelectric transducer on a pitch-plunge aerofoil with a finite-mass trailing-edge flap turns the limit cycle that follows flutter into electrical power. The design findings for such a harvester have so far been obtained with the section's suspension reacting against rigid ground, which is what a wind-tunnel mounting provides. Here a 3-dof aerofoil with a transducer is carried by a fuselage mass that is itself free to translate, so that the coupled system is free-free and the wing's plunge is measured relative to a support that moves. The support degree of freedom is destabilising on its own, softening the flutter mode by taking a share of it in antiphase with the wing's plunge, and it acts on the three transducer mountings unequally, amplifying the plunge mounting's destabilisation, leaving the largest pitch-mounted stabilisation untouched while halving it where the electrical time constant meets the flutter frequency, and leaving the flap mounting alone. The optimum coupling and load resistance do not move, so the matching rules of the rigidly supported section carry over unchanged. The harvested power rises with the support mass at a fixed flow speed for every mounting, and that rise is shown to be an artefact of the fixed-speed convention rather than a property of the cycle. Measured instead at a fixed margin above each system's own flutter boundary, which divides out the boundary's motion, the plunge mounting keeps a real gain while the pitch mounting loses power, so the apparent benefit of a soft support to a pitch-mounted harvester is entirely the boundary coming down to meet the flow speed. A harvester result quoted at a fixed speed and read as a property of the limit cycle is therefore wrong by the whole of that difference.

0.38

Profile-Anchored Control: Velocity Shaping with Exact Disturbance Rejection and Transient-Free Replanning

eess.SY math.OC ·2026-11-19 ·Christian Fredrik Sætre, Morten Dinhoff Pedersen
theory similarity 0.40
Abstract

In many motion-control problems, how a target is approached matters as much as whether it is reached: speed and deceleration must stay within actuator, safety or comfort limits despite unknown loads and disturbances. Position-dependent velocity profiles provide a natural way to describe such requirements. We show that the square of such a profile can be used both to plan the motion and to construct the controller that executes it. Our main result, profile-anchored control with exact rejection (PACER), recovers the nominal motion after a finite time under an unknown gain and load, and then allows the profile to be replaced mid-motion without a transient. It combines a static law for scalar second-order systems with a dynamic law for first-order ones, used for disturbance rejection. The static law guarantees uniform global asymptotic stability under an unknown input gain with a known lower bound, and finite-time stability under local homogeneity, while the first-order law gives analogous guarantees under disturbances of bounded rate and provides the exact rejection in PACER. Replanning of a profile under speed, acceleration and jerk limits can be formulated as a convex program. The approach is illustrated on a simulated elevator.

0.25

SCET-CBF: Speed-Calibrated Soft Guidance for One-Step Dynamic Navigation

cs.RO ·2026-10-24 ·Xiaoyu Han, Dongkun Han
similarity 0.40
Abstract · 9 pages, 6 figures

Control barrier functions (CBFs) support collision avoidance, yet dense dynamic encounters can leave a vehicle with no feasible command. Geometric refinements and soft constraints help preserve motion choices. Using these choices also requires accounting for the vehicle's changing turning response. For a steering-limited bicycle, braking can lower closing speed while slowing the lateral motion needed before an obstacle arrives. We propose SCET-CBF, a speed-calibrated soft guidance law for one-step dynamic navigation. A short lateral escape maneuver gives an allowable approach speed. Its speed derivative allows a quadratic program to weigh both effects of braking when choosing acceleration and steering. Soft penalties accommodate competing obstacle preferences within the input set permitted by segment and braking constraints. We derive the guidance and establish protection over each accepted motion segment, together with conditional braking invariance for a single obstacle. On 2500 paired tasks with a 60 s deadline, SCET achieves 72.8% completion, compared with 49.8% for CBF/velocity-obstacle control and 69.8% for an enhanced 1 s CBF-MPC. At 100 obstacles, SCET and the enhanced MPC complete 52.4% and 33.6% of tasks. Paired studies identify the contributions of speed feedback and early activation. Further evaluations examine the operating range under lateral acceleration limits and bounded motion and execution errors.

0.13

Co-Optimization of Scheduling, Control, and Incentivization of Electric Vehicles for Improving Power System Stability

eess.SY ·2026-10-10 ·Amit Kumer Podder, Tomonori Sadamoto, Aranya Chakrabortty
similarity 0.39
Abstract

We present a finite-horizon, greedy heuristic-based co-optimization and optimal control framework that jointly determines the optimized charging rates, charging times, and an optimal charging control law for electric vehicles (EVs) to improve both voltage stability and small-signal dynamic performance of a power distribution system. The proposed strategy encourages EV drivers to be flexible in choosing their charging rates and times through monetary incentivization under a fixed budget. The design is validated using the IEEE 33-bus distribution system model with ten EV charging stations (EVCSs). Results show that incentivizing drivers to settle for lower charging rates, implemented by a wait-and-save strategy, and rescheduling their charging times strategically can significantly improve the voltage stability index (VSI) of the system as well as the damping factors for the mid-frequency oscillation modes seen in the DC-link bus voltage.

0.20