CS Paper Radar

Piezoelectric Energy Harvesting from a Pitch-Plunge Aerofoil in Compressible Flow, the Euler Full-Order Model, Strip Theory and the Reduced Models Compared

Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken

cs.CE ·submitted 2026-09-16 12:55 UTC · v2

Abstract

A piezoelectric transducer embedded in a pitch-plunge aerofoil with a finite-mass trailingedge flap converts the limit-cycle oscillation that follows flutter into electrical power. The design findings for such a harvester have so far been obtained with incompressible strip theory, whose aerodynamic state is a handful of lag variables. Here the same section, the same transducer and the same test cases are coupled instead to the two-dimensional compressible Euler equations, giving a full-order model of twelve thousand states, and the two aerodynamic models are placed side by side on the flutter boundary, on the limit cycle and on the harvested power, with the strip-theory results compared against higher fidelity aerodynamic modelling provided by CFD. The degree of freedom carrying the transducer remains the first-order design variable, and the ranking of the mountings and the position of the optimum in the coupling and load-resistance plane are unchanged, while strip theory is found to underpredict the harvested power of the compressible section and to overstate the effect of the transducer on stability where the electrical time constant meets the flutter frequency. A nonlinear reduced model of four states, built on eigenvectors of the coupled Jacobian at the velocity of interest, reproduces the frequency of the cycle, its pitch amplitude, the transducer voltage and the mean power, and misstates the proportion of plunge to pitch in the orbit and its phase. That error is shown to be independent of the amplitude of the cycle and to survive enlargement of the basis, which places it in the retained subspace rather than in the order of the expansion, and suggests that such models should be judged on the shape of the orbit rather than on a single amplitude.

Comment
15 pages, 4 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Compressible aerodynamics and rigid-body support motion in post-flutter piezoelectric energy harvesting from a pitch-plunge-flap aerofoil

cs.CE ·2026-09-21 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
similarity 0.86
Abstract · 14, 3 figures

A piezoelectric transducer on a pitching and plunging aerofoil with a trailing edge flap turns the limit cycle that follows flutter into electrical power, and two modelling changes to that harvester have been studied separately. Replacing incompressible strip theory by the compressible Euler equations reduces the stabilising effect of a transducer mounted on the pitch, where the electrical time constant meets the flutter frequency, and raises the harvested power, and letting the section react against a fuselage free to translate, instead of rigid ground, does the same two things by about the same amounts. Here both changes are put in one model, which needs no new mesh motion in the flow solver, since the support's translation displaces the wall exactly as the plunge does. On the harvested power the two published corrections simply multiply. On the flutter boundary they more than compound, and at strong enough coupling they reverse the sign of the transducer's effect at the load resistance where both companion papers harvest, although neither change alone reverses it. The free support widens the band of resistance over which the two aerodynamic models disagree in sign, carrying its upper edge out by about a factor of three. Above the resistance where the electrical pole meets the flutter frequency, where the transducer acts as an added stiffness, the product of the published corrections predicts the shift to within seven parts in a thousand. Below it, where the transducer acts as a damper whose effect depends on phase, the product is wrong by a factor of up to fourteen, and on the pitch mounting by a sign. The same transducer lowers the boundary while flattening the growth of the instability above it. Whether corrections found one change at a time may be multiplied therefore depends on the quantity and, for the flutter boundary, on the regime of the transducer.

0.15

Transducer Placement and the Limits of a Four-State Reduced Model in Post-Flutter Piezoelectric Energy Harvesting from a Pitch-Plunge-Flap Aerofoil

cs.CE eess.SYmath-ph ·2026-09-11 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
unusualhighly cited similarity 0.85
Abstract · 16 pages; 6 figures;

Aeroelastic ?utter is normally a failure mode to be designed against, yet the limit-cycle oscillations (LCOs) that follow it convert flow energy into sustained structural motion that a piezoelectric transducer can turn into electrical power. A transducer is embedded in a three-degree-of-freedom pitch-plunge aerofoil with a finite-mass trailing-edge flap and unsteady strip-theory aerodynamics, giving a fifteen-state electro-aeroelastic system with a cubic hardening pitch spring, and the system is reduced by biorthonormal projection of the Taylor-expanded residual onto eigenvectors of the coupled Jacobian. The testbed is deliberately low order, so that every reduced prediction can be checked against the full-order system it replaces. The degree of freedom that carries the transducer is a first-order design variable, since it sets both the sign of the shift in the flutter boundary and the magnitude of the harvested power. The error of the reduced model is dominated not by the size of the retained basis but by how the reduced operator is made to depend on low speed. Expanding the retained eigenvalues leaves the reduced operator block-diagonal, with no coupling between the retained modes at any order of the expansion, whereas re-projecting the exact Jacobian onto the same frozen basis supplies that coupling and restores the structural response without enlarging the basis. It is found that the error that remains lies in the harvested voltage, which the equilibrium eigenvectors carry in a fixed proportion to the motion, and this is not removed by adding the electrical modes to the basis, whereas the flap detection, which the same basis also misses, is recovered by retaining the flap modes. The accuracy of a harvester reduced-order model must therefore be reported on the harvested quantity itself.

0.57

Rigid-body support motion and post-flutter piezoelectric energy harvesting from a pitch-plunge-flap aerofoil

cs.CE ·2026-09-21 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
similarity 0.77
Abstract

A piezoelectric transducer on a pitch-plunge aerofoil with a finite-mass trailing-edge flap turns the limit cycle that follows flutter into electrical power. The design findings for such a harvester have so far been obtained with the section's suspension reacting against rigid ground, which is what a wind-tunnel mounting provides. Here a 3-dof aerofoil with a transducer is carried by a fuselage mass that is itself free to translate, so that the coupled system is free-free and the wing's plunge is measured relative to a support that moves. The support degree of freedom is destabilising on its own, softening the flutter mode by taking a share of it in antiphase with the wing's plunge, and it acts on the three transducer mountings unequally, amplifying the plunge mounting's destabilisation, leaving the largest pitch-mounted stabilisation untouched while halving it where the electrical time constant meets the flutter frequency, and leaving the flap mounting alone. The optimum coupling and load resistance do not move, so the matching rules of the rigidly supported section carry over unchanged. The harvested power rises with the support mass at a fixed flow speed for every mounting, and that rise is shown to be an artefact of the fixed-speed convention rather than a property of the cycle. Measured instead at a fixed margin above each system's own flutter boundary, which divides out the boundary's motion, the plunge mounting keeps a real gain while the pitch mounting loses power, so the apparent benefit of a soft support to a pitch-mounted harvester is entirely the boundary coming down to meet the flow speed. A harvester result quoted at a fixed speed and read as a property of the limit cycle is therefore wrong by the whole of that difference.

0.38

How the elastic axis folds the transonic flutter boundary: shock energy transfer and conformally calibrated active learning

cs.LG physics.flu-dyn ·2026-10-16 ·Ashray Saxena, Sharad Shrivastava
publishedunusual similarity 0.53
Abstract · 28 pages, 15 figures, 8 tables. Accepted for publication in Transport Phenomena (Special Edition: Tribute to John Charles Slattery). Code an…

Isogai's case A, a pitch-plunge aerofoil whose elastic axis lies half a chord ahead of the leading edge, has a folded transonic flutter boundary in inviscid flow, with several flutter speeds at one Mach number. We map this boundary and its elastic-axis family with coupled Euler simulations, a Gaussian-process surrogate of the damping trained by batch active learning, and distribution-free split conformal prediction, which bounds the marginal error rate of stability calls. Three failure modes of damping labels are invisible in the residuals, and the half-degree mean incidence left by an impulsive start at $1^\circ$ freestream incidence raises the flutter speed at the dip by 2.8%, more than any numerical setting. With 80 simulations the learned case A boundary labels 63 of 64 independent runs correctly, and at most 1.8% of calibrated calls on held-out runs are wrong. Over Mach number, elastic axis and flutter speed index, 193 simulations show that, for the case A structure about the axis, the inviscid fold exists only for axes more than about 0.4 chord ahead of the leading edge, on two meshes. Chordwise energy budgets, closed three ways, explain both branches. On the lower branch the falling reduced frequency, at unchanged shock phase, raises the shock input and lowers the upstream damping similarly. On the upper branch the shock is pinned at the trailing edge; moving the axis aft brings the flutter-mode pivot towards the section, so the upstream damping falls faster than the residual shock input and the fold closes.

0.41

Structure-preserving reduced-order models of thin panels in supersonic and hypersonic flow

cs.CE cs.LGmath.NA ·2026-10-22 ·Miguel A. Aguilo
similarity 0.47
Abstract · 68 pages, 15 figures

We build structure-preserving reduced-order models for both challenge problems of the AePW-4 High-Speed Working Group. They are a clamped thin panel at Mach 1.92 (RC-19) and a cantilever plate at Mach 5.85 (HyMAX). The published data for each case hold no time-resolved response and no repeated runs. The physics must therefore be carried by the form of the model. One construction gives two models per problem. A Ritz-Galerkin reference model describes the plate. A learned model keeps the reference model's exact potential, fits the remaining generalized forces, and trains only a dissipation that cannot add energy. Its energy balance holds for any weights by construction. On the trained model the worst relative residual is 2.2e-15. On RC-19, shock relations predict a pressure ratio of 1.521 across the panel. Pressure-sensitive paint measured the same value. Thirty runs of the learned model place the mean dominant frequency within 1.0% of the measured 236 Hz. At one periodic and one chaotic condition, the learned model reproduces the response regime of a published reduced-order model in all sixteen runs. It does so without that model's 113 Hz spectral peak, which the measurements do not show. Measured displacements can also correct the chaotic response through one more force that respects the energy balance. We tested this on synthetic data at the experiment's 5 kHz sampling rate. The state error is 1.25% of the panel thickness without noise and 3.5% with 10 micrometers of noise. On HyMAX the learned model follows the reference model's trailing-edge displacement for 65 ms with a relative error of 3.7%. These results show that a model whose structure carries the physics can match measured flutter behavior when the available data cannot train it.

0.30

Nested Power Models for Multirotor Propulsion: From Aerodynamic Drag to Electrical Losses

cs.RO eess.SY ·2026-10-06 ·Antonio Franchi, Aaron Saini, Ahmed Ali, Chiara Gabellieri
unusual similarity 0.47
Abstract

Speed-only aerodynamic power models for multirotor propulsion cannot represent acceleration-dependent effects. This work develops a nested sequence of propulsion-power models that starts from aerodynamic power dissipation and progressively introduces a reversible kinetic-energy rate, torque-dependent electromechanical dissipation, and lumped speed-proportional dissipation. The models are identified using one subset of experiments and validated using the other on a motor-drive-propeller unit. Independent estimates of rotational inertia and aerodynamic drag complement predictive validation by assessing whether the models correctly attribute the measured power to reversible kinetic-energy exchange and irreversible dissipation and, within the latter, to aerodynamic and electromechanical losses. The results show that the reversible kinetic-energy rate is necessary but insufficient for accurate dynamic power prediction. Dissipation proportional to the squared motor torque provides the main additional improvement, while speed-proportional dissipation further prevents irreversible losses from being attributed to reversible kinetic-energy exchange. The resulting methodology provides a reusable and experimentally verifiable basis for developing and selecting dynamic propulsion-power models for multirotor systems.

0.25

Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

eess.SP ·2026-11-09 ·Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu +6 more
similarity 0.46
Abstract · 8 pages, 11 figures

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm$^{2}$, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency ($k_{\mathrm{eff}}^{2}$) of 3% and a moderate static capacitance $C_0$ of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement ($ξ_{\mathrm{static}}$) of 145 nm/V and a high corresponding open-circuit sensitivity ($S_{\mathrm{OC}}$) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

0.33

Aeroelastically Constrained Optimal Path Planning of a Fixed-Wing Airborne Wind Energy System

eess.SY ·2026-11-10 ·Omid Heydarnia, Jolan Wauters, Tom Lefebvre, Joris Degroote, Guillaume Crevecoeur
published similarity 0.45
Abstract

Multi-megawatt fixed-wing airborne wind energy systems (AWES) use an aircraft with large, slender wings that deform over the pumping cycle. To harvest maximum energy, the cycle is usually designed by means of dedicated reference trajectory optimization routines. It is well known that such routines rely heavily on the system model and that close alignment between the model and the physical system is required for the results to hold in practice. Nevertheless, the wing is usually treated as rigid and structural limits are respected indirectly through upper bounding of states and inputs. In this work, we directly enforce bounds on the elastic deflection and twist of the wing in the power-maximizing periodic optimal control problem. To that end, we model the wing by root-clamped modes, loaded by strip-theory aerodynamics and by the gravitational and inertial loads of the manoeuvring aircraft. To keep the problem tractable, the modal dynamics are replaced by their quasi-static equilibrium, which enters every discretization interval as algebraic constraints. For a multi-megawatt reference aircraft, the elastic twist near the wing tips reaches $1.03^\circ$ along the optimal rigid-wing trajectory. With a twist limit of $0.6^\circ$, the optimal trajectory delivers $31\,\%$ less mean power than the rigid-wing one, mainly through a lower tether tension during reel-out. Rigid-wing trajectory optimization can thus overestimate the power that the wing limits permit. Forward simulations that retain the modal dynamics demonstrate that the quasi-static deflection and twist deviate from the dynamic ones by less than $2\,\%$ of their limits. This work shows that elastic deformation can be accounted for in the trajectory optimization and that, depending on the wing limits, it can strongly reduce the achievable power.

0.32