CS Paper Radar

Structure-preserving reduced-order models of thin panels in supersonic and hypersonic flow

Miguel A. Aguilo

cs.CE cs.LGmath.NA ·submitted 2026-10-22 16:19 UTC · v1

Abstract

We build structure-preserving reduced-order models for both challenge problems of the AePW-4 High-Speed Working Group. They are a clamped thin panel at Mach 1.92 (RC-19) and a cantilever plate at Mach 5.85 (HyMAX). The published data for each case hold no time-resolved response and no repeated runs. The physics must therefore be carried by the form of the model. One construction gives two models per problem. A Ritz-Galerkin reference model describes the plate. A learned model keeps the reference model's exact potential, fits the remaining generalized forces, and trains only a dissipation that cannot add energy. Its energy balance holds for any weights by construction. On the trained model the worst relative residual is 2.2e-15. On RC-19, shock relations predict a pressure ratio of 1.521 across the panel. Pressure-sensitive paint measured the same value. Thirty runs of the learned model place the mean dominant frequency within 1.0% of the measured 236 Hz. At one periodic and one chaotic condition, the learned model reproduces the response regime of a published reduced-order model in all sixteen runs. It does so without that model's 113 Hz spectral peak, which the measurements do not show. Measured displacements can also correct the chaotic response through one more force that respects the energy balance. We tested this on synthetic data at the experiment's 5 kHz sampling rate. The state error is 1.25% of the panel thickness without noise and 3.5% with 10 micrometers of noise. On HyMAX the learned model follows the reference model's trailing-edge displacement for 65 ms with a relative error of 3.7%. These results show that a model whose structure carries the physics can match measured flutter behavior when the available data cannot train it.

Comment
68 pages, 15 figures

Closest papers

Nearest neighbours by meaning across the whole index.

How the elastic axis folds the transonic flutter boundary: shock energy transfer and conformally calibrated active learning

cs.LG physics.flu-dyn ·2026-10-16 ·Ashray Saxena, Sharad Shrivastava
publishedunusual similarity 0.51
Abstract · 28 pages, 15 figures, 8 tables. Accepted for publication in Transport Phenomena (Special Edition: Tribute to John Charles Slattery). Code an…

Isogai's case A, a pitch-plunge aerofoil whose elastic axis lies half a chord ahead of the leading edge, has a folded transonic flutter boundary in inviscid flow, with several flutter speeds at one Mach number. We map this boundary and its elastic-axis family with coupled Euler simulations, a Gaussian-process surrogate of the damping trained by batch active learning, and distribution-free split conformal prediction, which bounds the marginal error rate of stability calls. Three failure modes of damping labels are invisible in the residuals, and the half-degree mean incidence left by an impulsive start at $1^\circ$ freestream incidence raises the flutter speed at the dip by 2.8%, more than any numerical setting. With 80 simulations the learned case A boundary labels 63 of 64 independent runs correctly, and at most 1.8% of calibrated calls on held-out runs are wrong. Over Mach number, elastic axis and flutter speed index, 193 simulations show that, for the case A structure about the axis, the inviscid fold exists only for axes more than about 0.4 chord ahead of the leading edge, on two meshes. Chordwise energy budgets, closed three ways, explain both branches. On the lower branch the falling reduced frequency, at unchanged shock phase, raises the shock input and lowers the upstream damping similarly. On the upper branch the shock is pinned at the trailing edge; moving the axis aft brings the flutter-mode pivot towards the section, so the upstream damping falls faster than the residual shock input and the fold closes.

0.41

Reduced-Order Physics-Informed Neural Network with Adaptive Basis Refinement for Structural Identification

cs.CE physics.comp-ph ·2026-08-17 ·Rui Zhang, Konstantinos Vlachas, Eleni Chatzi
similarity 0.51
Abstract

Physics-informed neural networks (PINNs) provide a flexible framework for solving forward and inverse problems. However, their direct application to structural dynamics remains limited by high system dimensionality and model-form errors arising from incomplete physics. Reduced-order models (ROMs) can alleviate the dimensionality bottleneck, yet existing PINN-ROM couplings typically rely on fixed reduced subspaces, target forward simulations, or assume complete physics, restricting their use for inverse identification under parametric variability or incomplete system knowledge. To address these limitations, this work proposes a Reduced-Order Physics-Informed Neural Network (RO-PINN) framework with adaptive basis refinement for structural identification under known and incomplete physics. Via projection, reduced governing equations are embedded directly into the PINN loss, facilitating learning in a low-dimensional latent space. An adaptive scheme updates the projection basis during training so that the latent space is progressively realigned with evolving structural parameters or learned residual restoring forces. This realignment reduces basis-mismatch errors and limits their influence on the inferred residual force. The method is validated on a four-story steel frame with nonlinear hysteretic braces under sparse and noisy measurements. Results show parameter identification comparable to or more accurate than Bayesian model updating with lower computational cost in the considered cases, recovery of unmodeled nonlinear restoring forces under incomplete physics, and joint identification of residual restoring forces and structural parameters within the same framework. Overall, RO-PINN provides a unified framework for structural identification by integrating reduced-order modeling, adaptive basis refinement, and physics-informed learning within a single formulation.

0.34

Identifying the Shear Piezoelectric Coefficient using Physics-Informed Neural Networks under Exact Boundary and Initial Constraints

cs.LG physics.comp-phcond-mat.mtrl-sciphysics.app-ph ·2026-11-02 ·Suhas Suresh Bharadwaj
similarity 0.49
Abstract · 19 pages, 9 figures

The shear piezoelectric coefficient $e_{15}$ governs the shear-mode electromechanical coupling in piezoelectric micromachined ultrasonic transducers (PMUTs) and surface acoustic wave (SAW) devices, but measuring it typically requires destructive resonance testing on dedicated specimens. On simulated data, $e_{15}$ can instead be recovered non-destructively from sparse, noisy subsurface wavefield observations using a constrained physics-informed neural network (PINN). By building exact spatial distance functions and temporal multipliers directly into the network output, the clamped, grounded boundaries and resting initial state hold automatically, leaving the loss with only the interior equations of coupled electro-elastodynamics and the data misfit. Non-dimensional scaling brings all governing coefficients within one decade of O(1), and the setup removes the boundary and initial-condition penalty weights that soft-constraint methods must tune. In a six-way comparison (plane-strain PZT-5H, manufactured wavefield, 30 dB noise), a soft-penalty baseline with adaptive weights converges to an erroneous $e_{15}$ in four of the five runs (51.7% mean error), and fixed penalties reach an error of 0.85% only after a second-order optimization stage. The constrained formulations reach mean $e_{15}$ errors between 0.15% and 0.51% with held-out displacement errors below 1%. Within these variants, the spatial multiplier gives rapid first-order convergence, and the quadratic temporal multiplier lowers the early-time electrostatic residual by a factor of 6.8 versus a linear one. On finite-element data along one subsurface line, the full formulation recovers $e_{15}$ with 1.19% mean error at 30 dB and keeps it between 0.65% and 2.71% across a 40 to 0 dB noise sweep. Finally, training on displacements alone still recovers $e_{15}$ with mean errors of 0.45% on finite-element and 1.64% on manufactured data.

0.27

Full-Order Safety for Nonlinear Reduced-Order MPC

cs.RO eess.SYmath.OC ·2026-10-13 ·Luis Pabon, Johannes Köhler, Revant Kasichainula, Marco Pavone
code/data similarity 0.48
Abstract · 8 pages, 4 figures

Reduced-order models (ROMs) make model predictive control (MPC) of high-dimensional nonlinear systems tractable, but the resulting modeling error can lead to constraint violations on the real system. We introduce CoRE-MPC, a robust MPC formulation that plans with a nonlinear ROM and guarantees recursive feasibility and constraint satisfaction for the full-order system. It can be applied with a broad class of nonlinear model reduction techniques and the resulting MPC does not require evaluating the full-order model online, thus ensuring computational efficiency. The key insight is in how the ROM affects the dynamics of the prediction error. We account for this with two error radii that are propagated alongside the ROM and provide a guaranteed bound on the prediction error. The approach is validated in simulation on an 80-state oscillator chain, a Burgers equation, and a 9,768-state finite-element soft robot, where a two-state ROM with data-driven bounds keeps all 1,628 nodes clear of a wall at a median solve time below 1 ms for a 20 ms control period. Across these examples, CoRE-MPC is 13 to 61 times faster than full-order robust MPC at only 27 to 35% higher closed-loop cost, whereas existing certified schemes are either infeasible or at least twice as conservative. Code: [released upon publication].

0.41

Hyperreduction accelerates finite element model updating for the discovery of neural materials

cs.CE cs.AI ·2026-10-22 ·Hagen Holthusen, Matthias Knipper, Kevin Linka
similarity 0.48
Abstract · 42 pages, 23 figures, 1 table

Finite element model updating is among the most general approaches to discover constitutive models from structural experiments: since the displacement field is computed rather than measured, it accommodates arbitrary geometries, boundary conditions, and sparse or noisy data. However, every loss evaluation requires a nonlinear finite element solve per load step, and training neural materials requires many such evaluations. Intrusive model order reduction lowers this cost while retaining boundary conditions and variational structure. How can a reduced model remain accurate while the network weights change at every training step? We combine proper orthogonal decomposition and energy-conserving sampling and weighting with adjoint sensitivities of the reduced model, and adapt both the trial space and the sampled elements along the optimization path. The constitutive law is a polyconvex neural network: a logarithmic normalization term, together with a zero-anchored input convex architecture and a growth term, renders the energy polyconvex, coercive, and non-negative by construction, independent of the trained weights. We demonstrate the approach on two experimental datasets and one synthetic three-dimensional example. For a two-phase specimen, training time decreases from nine hours to 41 minutes compared with a full-order identification, without loss of accuracy. In the three-dimensional example, six modes replace 48 672 degrees of freedom, 116 of 15 625 elements suffice to evaluate the internal forces, and training takes 13 minutes. In all cases, the identified material reproduces the measured reaction force and predicts the displacement field from the force alone. Hyperreduction makes the discovery of neural materials from structural data affordable while retaining the advantages of finite element model updating.

0.28

Transducer Placement and the Limits of a Four-State Reduced Model in Post-Flutter Piezoelectric Energy Harvesting from a Pitch-Plunge-Flap Aerofoil

cs.CE eess.SYmath-ph ·2026-09-11 ·Nikolaos D. Tantaroudas, Ilias Karachalios, Andrew J. McCracken
unusualhighly cited similarity 0.48
Abstract · 16 pages; 6 figures;

Aeroelastic ?utter is normally a failure mode to be designed against, yet the limit-cycle oscillations (LCOs) that follow it convert flow energy into sustained structural motion that a piezoelectric transducer can turn into electrical power. A transducer is embedded in a three-degree-of-freedom pitch-plunge aerofoil with a finite-mass trailing-edge flap and unsteady strip-theory aerodynamics, giving a fifteen-state electro-aeroelastic system with a cubic hardening pitch spring, and the system is reduced by biorthonormal projection of the Taylor-expanded residual onto eigenvectors of the coupled Jacobian. The testbed is deliberately low order, so that every reduced prediction can be checked against the full-order system it replaces. The degree of freedom that carries the transducer is a first-order design variable, since it sets both the sign of the shift in the flutter boundary and the magnitude of the harvested power. The error of the reduced model is dominated not by the size of the retained basis but by how the reduced operator is made to depend on low speed. Expanding the retained eigenvalues leaves the reduced operator block-diagonal, with no coupling between the retained modes at any order of the expansion, whereas re-projecting the exact Jacobian onto the same frozen basis supplies that coupling and restores the structural response without enlarging the basis. It is found that the error that remains lies in the harvested voltage, which the equilibrium eigenvectors carry in a fixed proportion to the motion, and this is not removed by adding the electrical modes to the basis, whereas the flap detection, which the same basis also misses, is recovered by retaining the flap modes. The accuracy of a harvester reduced-order model must therefore be reported on the harvested quantity itself.

0.57

Efficient Projection-Based Reduced-Order Modeling for Computational Fluid Dynamics via Multifidelity Basis Construction

cs.CE ·2026-11-04 ·Ashok Viswanathan, Charbel Farhat
similarity 0.48
Abstract · 18 pages conference

Projection-based reduced-order models (PROMs) accelerate computational fluid dynamics simulations, but generating high-fidelity (HF) training snapshots remains expensive. We present a multifidelity methodology that reduces offline basis-construction costs by combining a small HF database with low-fidelity (LF) solutions. The method accommodates discrepancies in physical models and spatial discretizations. Parameter-matched HF and aligned LF snapshots define a correction basis. At new parameters, LF predictions are corrected by minimizing the HF residual over an affine trial space, with selective Reynolds-averaged Navier-Stokes (RANS) smoothing. Accepted snapshots enrich the training database and update the correction basis. The resulting basis is compatible with conventional projection methods, including least-squares Petrov-Galerkin projection. For steady flow over a NACA0012 airfoil, using fine-grid RANS and coarse-grid Euler models, four HF snapshots and 36 LF-derived snapshots reduce snapshot-generation cost by a factor of 7.8. At basis dimension 40, mean lift, drag, and lift-to-drag ratio errors are 1.1%, 3.6%, and 3.9%, and the mean relative skin-friction error is approximately 5%, compared with 0.18%, 2.9%, 2.8%, and 4% for an HF-only PROM. Errors are evaluated against fully converged HF solutions on a test set emphasizing shock-containing flows. Increasing the initial HF snapshot count raises cost without monotonically improving accuracy. Among the tested multifidelity configurations, ten initial HF snapshots give the lowest aerodynamic errors at dimension 40; increasing the count to twelve worsens all three. The results demonstrate reduced snapshot-generation costs while retaining compatibility with established PROM formulations.

0.32

Glass-Box Deep Reinforcement Learning for High-Speed Flow Control

cs.LG ·2026-10-19 ·Ameya D. Jagtap
position similarity 0.47
Abstract · 22 pages

Deep reinforcement learning (DRL) is challenging long-held assumptions in active flow control. By learning directly from interaction with a flow, DRL agents can find actuation strategies for nonlinear, unsteady flows without explicit models, often exploiting mechanisms that classical control would not anticipate. High-speed flows are a demanding test of this promise: shocks, shock/boundary-layer interactions, transition, aerothermal loading and microsecond-scale dynamics strain both algorithms and hardware. Yet most demonstrations remain idealized, low-speed simulations with limited evidence of robustness, interpretability, transferability or experimental deployment. In this perspective, we examine what constrains DRL-based high-speed flow control, including compressible simulation cost and fidelity, data efficiency, sensing in extreme environments, reward design, explainability, and generalization across Mach and Reynolds number. We argue that these limits reflect a tension between data-driven optimization and the structured physics, constraints and uncertainties of real flows. We then highlight where DRL may go beyond conventional approaches: adaptive control of shock-induced separation and turbulent boundary layers, coordination of distributed actuators, and discovery of unconventional flow-manipulation mechanisms.The central challenge, however, is translating these capabilities into reliable technology, which will require validated compressible simulation environments, physics- and constraint-aware learning, robustness to off-design conditions and sensor degradation, real-time operation, hardware-in-the-loop and wind-tunnel validation, and credible pathways to safety and certification.

0.29