CS Paper Radar

Electric Racing Kart with BLDC Drive, LiFePO4 Battery System, Traction Control and Regenerative Braking

Johannes Stockhammer, Tom Rettenwander, Philipp Huber

eess.SY ·submitted 2026-10-06 19:01 UTC · v1
publishedunusual

Abstract

This diploma thesis documents the conversion of a petrol-powered go-kart into a battery-electric kart with a 10 kW BLDC drive, a LiFePO$_4$ traction battery with battery management system, a slip-based traction control and regenerative braking. The traction control estimates the slip of the driven rear axle from three Hall-effect wheel-speed sensors as $λ= (v_R - v_F)/v_R$ and reduces the torque command of the throttle pedal when the axle slips. It runs on a 32-bit ARM Cortex-M3 microcontroller (SAM3X8E) in the signal path between pedal and motor controller, with galvanic isolation and an emergency stop. Regenerative braking uses the generator mode of the motor controller in three stages: motor brake on throttle release, light braking via a steering-wheel button, and blended braking with the hydraulic brake. Drivetrain calculations show that the kart is traction-limited. At rated torque, the drive force at standstill exceeds the transmissible traction force by a factor of 1.7 to 2.0, up to approx. 27 to 43 km/h. Traction control is therefore a functional requirement of the drivetrain. The calculated top speed is approx. 65 km/h. Regenerative braking reaches approx. 0.45 g and could cover up to about 30 % of the energy demand on a winding track. With 80 % of the nominal battery energy, approx. 44 min of driving at 50 % motor load result, so the target of one hour is missed. The initial charging measurement quantifies the flat LiFePO$_4$ voltage plateau at 0.7 to 1.8 mV per percent state of charge, which makes voltage-based state-of-charge estimation unreliable. Cold cells showed a voltage sag under load that triggered the low-voltage alarm. Validation of the control functions by instrumented driving tests is the main open point.

Comment
German title: Elektro-Rennkart mit BLDC-Antrieb, LiFePO4-Batteriesystem, Antischlupfregelung und Rekuperation. Diploma thesis, HTL Braunau, Austria, 2016. Third, revised English edition, 2026, revised and translated by Johannes Stockhammer. 69 pages, 36 figures, 15 tables
DOI
10.5281/zenodo.23072034

Closest papers

Nearest neighbours by meaning across the whole index.

Direct Electromechanical Actuation of the Shift Drum in Non-Synchronized Motorcycle Transmissions: From Actuator Sizing and Electronics Design to Closed-Loop Position Control

eess.SY ·2026-10-12 ·Johannes Stockhammer
unusual similarity 0.50
Abstract · Original German title (2019): Entwickeln eines automatisierten Schaltgetriebes fuer Motorraeder. Diploma thesis, Westsaechsische Hochschule …

This thesis presents the direct electromechanical actuation of the shift drum in a non-synchronized motorcycle transmission. A DC motor drives the shift drum through a self-locking worm gear, so the entire foot shift mechanism is eliminated. As a reference, 84 manual gear changes of a large-displacement series-production motorcycle were measured on a chassis dynamometer; the mean shift time is 80 ms for upshifts and 92 ms for downshifts. The system design covers the complete chain from the mechanics to the software. The actuator motor is sized from inertia, friction and gear ratio. A dedicated shift controller is developed with supply filtering, signal conditioning for the position sensor and the incremental encoder, an H-bridge motor driver and a custom circuit board based on a SAMD21 microcontroller. The embedded firmware implements position control of the shift drum with a proportional controller, without inner speed or current loops. On a gearbox test rig, a gear change is completed in less than 80 ms without overshoot in a single measurement, below the mean of the manual reference shifts. The analysis reveals a trade-off in the choice of the worm gear ratio: at a ratio of 30, about 93% of the motor torque is needed to accelerate the motor shaft and the worm. A ratio of about 8 halves the required torque, but the worm gear then loses its self-locking. The measured shift times are published as an open dataset.

0.34

Model predictive traction control system based on the Koopman operator

eess.SY ·2026-08-26 ·Josip Kir Hromatko, Šandor Ileš
publishedcode/data similarity 0.50
Abstract · 6 pages, 4 figures; associated code available at https://github.com/PVDC-project/pvdc-kmpc-traction-control

Due to their importance, traction control and anti-lock braking systems have become standard equipment in modern vehicles. However, accurate models of tire dynamics are often difficult to obtain and usually include nonlinearities, making their use in control systems challenging. This paper describes a traction control system based on model predictive control and Koopman operator theory, which aims to approximate nonlinear systems with linear ones through a state space transformation. A linear model predictive controller based on the Koopman predictor is compared to a standard nonlinear model predictive controller. Experiments in a high-fidelity vehicle dynamics simulation environment show a comparable reference tracking performance of the two controllers, with a reduced execution time for the proposed Koopman operator-based algorithm, both on a standard PC and embedded hardware.

0.78

Enhancing Energy Harvesting in Harmonically Forced Oscillators via Regenerative Impulsive Braking

eess.SY ·2026-10-06 ·Nilay Kant
unusual similarity 0.49
Abstract

This paper investigates whether regenerative impulsive braking can enhance passive energy harvesting in harmonically forced oscillators. An impulsive braking event directly extracts kinetic energy while simultaneously inducing a transient that alters subsequent passive harvesting. The analysis shows that suitably timed braking can produce a net energy gain over passive harvesting alone. The braking-induced transient is derived analytically and used to obtain an exact expression for the harvested-energy gain over an arbitrary finite post-braking horizon, together with conditions for positive gain and the optimal braking instant. The corresponding infinite-horizon analysis shows that optimal braking occurs at zero crossings of the harmonic excitation, with complete braking maximizing the gain. Numerical results further show that the finite-horizon harvested-energy gain can exceed its infinite-horizon value. Simulations using short-duration high-gain braking closely match analysis, supporting potential of the proposed approach for energy-harvesting applications.

0.25

A Hybrid UKF with Explicit Drivetrain Modeling for Low-Velocity State Estimation of Electric Vehicles

eess.SY ·2026-11-05 ·Hendrik Schäfke, Daniel O. M. Weber, Thomas Seel, Askar Vagapov, Jannes Iatropoulos +4 more
similarity 0.48
Abstract · 14 pages, 11 figures, 3 tables. Submitted to IEEE Transactions on Intelligent Vehicles

Longitudinal velocity is a core input for vehicle control, driver-assistance, and automated driving functions. Production wheel-speed sensors deliver only a few pulses per revolution, so they lose resolution below 1 km/h, the regime in which automated parking and traffic-jam assistance operate. The motor speed from the electric machine's resolver stays finely resolved down to standstill but reaches the wheels only through a compliant drivetrain. We therefore estimate the longitudinal velocity with an unscented Kalman filter (UKF) on a double-track model adapted to low velocities and incorporate the motor speed along two routes, one purely physical and one hybrid. The first augments the model with an explicit torsional spring-damper drivetrain, making the motor speed a state of the estimator. The second feeds the output of a neural network-based virtual wheel-speed sensor into the UKF as a pseudo-measurement. Both routes are compared against two baselines, a wheel-speed-only configuration and one that adds the motor-speed sensor but treats the driveline as rigid. Because the model is numerically stiff near standstill, the comparison rests on a systematic study of explicit and semi-implicit discretization schemes. All four configurations are evaluated against an inertial reference in real-world test drives with two distinct series-production electric vehicles, anonymized as Vehicle A and Vehicle B for confidentiality. Below 1 km/h, both proposed estimators lower the velocity root-mean-square error by at least 54% and 45% against both baselines on Vehicle A. Carried over zero-shot to Vehicle B without re-tuning on target-vehicle data, they lower it by at least 41% and 51%. Both estimators therefore carry across vehicles without a new identification campaign.

0.33

Event-Driven Safe Control of a Black-Box Balancing Wheel with Friction-Gated Actuation

eess.SY ·2026-10-12 ·Kanishka Harwani, Neha Navarkar, Aliasghar Arab, Farshad Khorrami
code/data similarity 0.45
Abstract

Commercial balancing wheels are closed systems: an internal controller keeps the board upright, and a rider steers by shifting weight and twisting the hips. We augment a one-wheel with a lead-screw weight shift for longitudinal motion and a reaction wheel for yaw. The reaction wheel stores limited momentum, so a turn is a sequence of torque pulses, and whether a pulse rotates the body depends on static friction at the tire contact. From a 24-pulse torque sweep on one surface we fit a two-part model that gives the probability that a pulse rotates the body, treating the breakaway torque as random, and the rotation angle when it does; at maximum torque the posterior engagement probability is 0.54 (90% credible interval 0.24-0.84). The weight shift is modeled as a rate- limited input with a measured speed gain and an assumed first-order response, which predicts stopping distances four times those of a direct-force model. These models drive an event-triggered supervisor that schedules pulses by expected heading improvement, brakes when the predicted braking path would leave the safe set, tightens margins for model uncertainty, and updates the friction estimate online. In simulation on 500 plants drawn from the fitted models, the robust supervisor completed 92.6% of missions with 1.8% safety violations and 1.6% safe aborts, versus 84.0% and 7.2% for a supervisor using mean models and 1.8% and 20.4% for a baseline that ignores friction. A video of the hardware experiments is available online (https://github.com/ASAS-Labs/x-wheel).

0.33

Energy-Aware Path Following: Comparative Analysis of Reinforcement Learning and NMPC for Electric Vehicles

cs.RO cs.LGeess.SY ·2026-10-06 ·Mohamed Sabaa, Mostafa Emam
similarity 0.45
Abstract · 20 pages, 12 figures, currently submitted for review at the journal (Robotics and Autonomous Systems) https://www.sciencedirect.com/journal/…

Path-following control strategies typically follow the bi-objective optimization dilemma: minimizing deviations from a reference path while maintaining smooth speed profiles. The latter objective is especially relevant for Electric Vehicles (EVs), since their limited driving range can be extended by recovering energy through regenerative braking, a feature that has not yet been sufficiently studied in the literature. In this work, we perform a comparative analysis of four controllers under one common Frenet frame-based kinematic vehicle model, utilizing a validated energy model (VT-CPEM) with explicit regenerative braking. Herein, we implement the following controllers: Nonlinear Model Predictive Control (NMPC), Proximal Policy Optimization (PPO), gain-scheduled Ackermann state-feedback baseline (PID-SF), and a Stanley geometric baseline. To satisfy real-time requirements, we implement the NMPC using JIT-compiled CasADi. Moreover, we train the PPO using traditional straight and S-curve tracks, after which we successfully transfer the unmodified policy to unseen tracks, including: an ISO 3888-1 lane-change, a chicane, randomly-generated parameterized-splines, and a $\pm3^\circ$ graded road. In addition, the policy transfers to a dynamic single-track vehicle model with linear tires, zero-shot with an acceptable initial performance, which was optimized after brief fine-tuning. Thereby, we demonstrate that our PPO is readily transferable to more comprehensive vehicle models. We conclude with a performance analysis of developed controllers and discuss ideas for future work.

0.25

Path-Following Control and Terramechanics Analysis for Planetary Rovers Under Wheel-to-Wheel Traction Asymmetry

cs.RO ·2026-09-30 ·Ryuya Matsuoka, Keisuke Takehana, Kentaro Uno, Toshinori Kuwahara, Kazuya Yoshida
published similarity 0.45
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

This paper proposes a control strategy for path following that is model-free and relies solely on deceleration for skid-steering planetary rovers navigating deformable loose terrain under continuously imposed traction asymmetry. While conventional controllers that are based on kinematics frequently cause slip-sinkage entrapment by accelerating the wheels during path correction, the proposed approach prevents this failure by setting an upper limit on the maximum commanded velocity. Heading correction is achieved solely through the selective deceleration of the outer wheels, which are located on the outside of the turn, driving them into a negative slip regime to act as a mechanical anchor. The system was evaluated using the four-wheel independent-drive rover EX1 under an asymmetric wheel configuration with different left and right grouser heights that induces significant deviations from the path. Experimental results demonstrate that this deceleration-only control successfully suppresses accumulated lateral drift across various velocity regimes up to 0.7 m/s without causing sinkage. Crucially, direct force measurements from onboard multi-axis sensors provide important empirical evidence of the underlying terramechanics, proving that the targeted deceleration establishes dynamic load equalization across the chassis and completely restores the native thrust capability of the opposite driving wheel.

0.37

Vehicle Drift Emergence: Continuous Evolution from Grip Driving to the Handling Limit via Boundary Exploration Learning Model Predictive Control

cs.RO ·2026-08-28 ·Sheng Zhao, Binh-Minh Nguyen, Hangyu Lu, Xiaodong Wu
similarity 0.44
Abstract

Automated drift controllers commonly track a prescribed drift equilibrium, sideslip reference, or trajectory. These formulations establish how to execute drift, whereas the continuous transition from grip driving to drift near the handling limit remains unresolved. This paper defines drift emergence in a repetitive lap time minimization task, where neither the controller objective nor the reward contains an explicit drift reference. A boundary exploration learning model predictive controller (BE-LMPC) constructs an empirical safe set and a locally shifted terminal cost from completed laps. By iteratively improving spatial speed allocation under a fixed global speed bound, the controller progressively explores larger sideslip and yaw rate envelopes while preserving recoverability. As lap performance improves, sustained sideslip and pronounced yaw motion emerge while the rear axle approaches saturation. Analysis shows that, when external conditions vary smoothly, the transition from tire adhesion to sliding does not itself cause abrupt changes in tire force or vehicle state. The combined-slip Fiala model satisfies this continuity condition at the transition. At a tire road friction coefficient of 0.6, lap time decreases from 49.95 s on Lap~3 to 25.50 s on Lap~12, with drift first emerging on Lap~11. Lap~12 reaches 16.5$^\circ$ sideslip and 0.894 rear axle utilization. In contrast, no drift is detected for friction coefficients from 0.8 to 1.2; at 1.2, a similar peak speed is achieved with only 0.483 rear axle utilization. These results characterize drift as a conditional continuation of limit handling that emerges when increasing performance demand approaches the available tire capacity, rather than as a separately prescribed motion mode.

0.32