CS Paper Radar

Path-Following Control and Terramechanics Analysis for Planetary Rovers Under Wheel-to-Wheel Traction Asymmetry

Ryuya Matsuoka, Keisuke Takehana, Kentaro Uno, Toshinori Kuwahara, Kazuya Yoshida

cs.RO ·submitted 2026-09-30 00:50 UTC · v1
published

Abstract

This paper proposes a control strategy for path following that is model-free and relies solely on deceleration for skid-steering planetary rovers navigating deformable loose terrain under continuously imposed traction asymmetry. While conventional controllers that are based on kinematics frequently cause slip-sinkage entrapment by accelerating the wheels during path correction, the proposed approach prevents this failure by setting an upper limit on the maximum commanded velocity. Heading correction is achieved solely through the selective deceleration of the outer wheels, which are located on the outside of the turn, driving them into a negative slip regime to act as a mechanical anchor. The system was evaluated using the four-wheel independent-drive rover EX1 under an asymmetric wheel configuration with different left and right grouser heights that induces significant deviations from the path. Experimental results demonstrate that this deceleration-only control successfully suppresses accumulated lateral drift across various velocity regimes up to 0.7 m/s without causing sinkage. Crucially, direct force measurements from onboard multi-axis sensors provide important empirical evidence of the underlying terramechanics, proving that the targeted deceleration establishes dynamic load equalization across the chassis and completely restores the native thrust capability of the opposite driving wheel.

Comment
Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

Closest papers

Nearest neighbours by meaning across the whole index.

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.62
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18

Floor Friction Assessment from Robot Tire-Surface Interaction

cs.RO ·2026-10-24 ·Kulbhushan Komarraju, Nathaniel Pearson, Yu Gu, Jason Gross
similarity 0.62
Abstract · 11 pages and 14 figures; Extended abstract submitted to IEEE/ION PLANS 2027, under review

Floor traction influences wheel-slip behavior, dead-reckoning accuracy, and the navigation performance of wheeled mobile robots that rely on wheel odometry. As these robots become increasingly common in GNSS-denied indoor environments, including automated manufacturing and retail facilities, their onboard measurements could also be used to characterize floor conditions and improve localization. In this study, a skid-steer robot was driven over five floor surfaces with distinct traction characteristics using commanded velocity profiles designed to induce wheel slip through repeated acceleration and direction reversal. Differences between the body velocity estimated from inertial sensing and the velocity obtained from wheel odometry were evaluated using the integrated relative-velocity error, phase-derived wheel-to-body response delay, and velocity-reversal response delay. Welch power spectral density analysis was additionally applied to characterize the frequency distribution of the velocity mismatch during positive and negative acceleration. Band-integrated spectral power, spectral centroid, and spectral decay rate were extracted from each recording and evaluated using linear discriminant analysis and multiclass classification. The response-delay measurements produced consistent surface-dependent trends, with the longest delays observed on soap and the shortest delays observed on carpet. The spectral features also provided clear separation among the tested surfaces, achieving a balanced classification accuracy of 97.1% under recording-level cross-validation. These results demonstrate that both the magnitude and frequency domain characteristics of wheel-to-body velocity mismatch contain useful information about tire-surface interactions. Such information could support surface recognition and the development of slip-aware wheel-odometry weighting within robot state-estimation frameworks.

0.25

Emergency Obstacle Avoidance Maneuvers in Differential-Drive Mobile Robots

cs.RO eess.SY ·2026-10-04 ·Kautik Mandve, Nilay Kant
similarity 0.58
Abstract

Emergency obstacle avoidance requires a mobile robot to brake or change its heading within the available distance. This paper investigates the dependence of maneuver performance and odometric error on approach speed for a differential-drive robot. A footprint-clearance analysis and a normalized wheel-motion index provide a kinematic description of five braking and turning maneuvers. The principal experiment comprises 540 block-randomized trials on tile, of which 539 are retained, at commanded approach speeds of 45, 55, and 65 cm/s. An overhead camera provides an independent pose reference. When encoder, gyro, and camera heading changes are evaluated over complete motion records, the mean encoder discrepancy increases by 4.7-5.1 degrees for the two reverse-spin maneuvers between the lowest and highest speeds; the arc and brake-assisted pivot change by less than 0.4 degrees. Larger encoder discrepancy is associated with lower avoidance success after adjustment for distance, speed, maneuver, day, and turn direction. Gyro discrepancies remain approximately 3 degrees for the reverse spins. Estimated reaction distances for 90% success and their uncertainty quantify the maneuver trade-offs. The results support speed-specific empirical characterization of emergency maneuvers and distinguish encoder error from recovery motion and measurement-window mismatch.

0.31

Inertial Steering and Motion Prediction of Tracked Vehicles on Low-Adherence Surfaces

cs.RO eess.SY ·2026-10-28 ·Mathis Turgeon-Roy, Mohamed Ounally, Veronica Vannini, Olivier Roy, François Pomerleau
similarity 0.58
Abstract

Tracked vehicles are widely used in off-road applications, but their conventional motion models often rely on no-slip assumptions that become inaccurate on low-adherence surfaces. Rather than treating inertial effects arising from slip as a disturbance to be minimized, this work investigates how inertial effects arising from a moving mass can be deliberately exploited for steering on low-friction surfaces. A dynamic model for an articulated tracked vehicle with a passive trailer is developed, allowing inertial effects from trailer motion to be captured. The approach is experimentally evaluated on ice, where our dynamic model outperforms the kinematic baseline. We also propose a mixed dynamic-kinematic model to adapt predictions to both surface and situation by exploiting predictions from both methods. Finally, we demonstrate inertial steering on a mono-track vehicle without a conventional steering mechanism, showing that controlled movements of an internal mass can generate turning motion on ice. The resulting behavior can be predicted using the proposed dynamic model by representing the internal mass as a frictionless trailer, revealing the analogous dynamics between the two configurations. These results demonstrate the feasibility of inertial steering as an alternative steering mechanism for tracked vehicles operating in low-adherence environments.

0.21

An Adaptive Control Architecture for Slope and Terrain Compensation in Autonomous Navigation in Mediterranean Greenhouses

cs.RO ·2026-09-02 ·Fernando Cañadas-Aránega, Dirk Wollherr, José L. Guzmán, José C. Moreno, José L. Blanco-Claraco
similarity 0.56
Abstract

The ability to move stably over terrain with varying slopes and textures is essential for mobile agricultural robots operating in complex and dynamic environments such as greenhouses, where small terrain irregularities can lead to significant navigation errors. This article presents a novel terrain-adaptation strategy based on the carried payload, ensuring accurate and robust trajectory tracking. The proposed approach is based on: (i) the experimental characterization of the most common types of greenhouse soil, concrete, compacted sand, and gravel, and (ii) the direct measurement of terrain slope using the IMU, in order to estimate the force with which this angle affects the motor input. Based on this information, a cascade trajectory-tracking scheme has been designed, consisting of a model-based predictive controller (MPC) in the outer loop and a PI controller in the inner loop. The system incorporates an adaptive feedforward control through gain scheduling approach, capable of adjusting to disturbances caused by variations in slope and terrain type. Simulation results demonstrate that the differential-drive robot achieves a significant improvement both in error indices and in control signal efficiency, highlighting the effectiveness and robustness of the proposed approach.

0.44

Mapless, Stabilizing, and Anti-Stuck Flipper Control for Articulated Tracked Robots

cs.RO ·2026-10-09 ·Valentýn Číhala, Pavel Sarga, Martin Pecka, Tomáš Svoboda, Karel Zimmermann
similarity 0.55
Abstract · 8 pages, 3 figures and 2 tables

Nearly every autonomous or semi-autonomous flipper controller assumes access to an elevation map of the terrain under and in front of the robot. The terrain beneath the chassis is occluded in the sensors, so the map is remembered through odometry integration, whose drift corrupts it. We present Stabilizing Anti-Stuck (SAS), a mapless controller that combines a stabilization term for body roll and pitch with an anti-stuck term that frees the robot when it gets stuck. As input, SAS uses the IMU, the flipper joint angles, and a motion cue that only tells whether the robot is moving. The cue is computed over a short window and never accumulated, so SAS does not inherit the odometry-integration drift that corrupts the map. We deploy SAS on a tracked robot with four flippers and evaluate it against manual teleoperation and prior flipper controllers in a large comparison, both in simulation and on a real obstacle. In simulation and on the real robot, SAS achieves traversal quality comparable to state-of-the-art map-based controllers. On a log hidden in tall grass, invisible to the LiDAR, the best map-based controller gets stuck while SAS traverses the hidden obstacle without a problem.

0.34

Slip-Induced Fall Suppression During Cornering for a Remotely Operated Motorcycle with a Rear-Wheel-Swing Mechanism

cs.RO eess.SY ·2026-10-15 ·Tadashi Sumioka, Kazushi Akimoto, Takuya Tsujimura, Sho Takayanagi, Kineo Tomura
similarity 0.55
Abstract · Journal papaer, 12 pages, 13 figures

Slip-induced falls when riding motorcycles are difficult to avoid even for expert riders and represent a major cause of single-vehicle accidents. Despite their prevalence, no practical solution has yet been proposed to suppress this phenomenon. We previously introduced a motorcycle model applicable to systems with both front- and rear- wheel steering. In this paper, we extend that model and formulate the suppression of slip-induced falls as an optimization problem that distributes assistive control inputs according to vehicle speed and road surface conditions. To evaluate the proposed method, we developed a remotely operated motorcycle and conducted experiments under two scenarios: slalom driving on a low-friction surface at 5.5 m/s, and turning maneuvers on synthetic ice to simulate driving over manholes on rainy days. The results demonstrate that our approach successfully suppresses falls under these challenging conditions.

0.25

Observability Analysis and Online Calibration of Visual-Inertial-Wheel Odometry for 4WIS4WID Mobile Robots

cs.RO ·2026-09-29 ·Branimir Ćaran, Vladimir Milić, Bojan Šekoranja, Bojan Jerbić
similarity 0.55
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

In this paper, we present a visual-inertial-wheel odometry (VIWO) framework with online calibration for four-wheel independently steered and driven (4WIS4WID) mobile robots. We derive a 2D odometry model directly from the four driving velocities and steering angles, using both the longitudinal rolling constraints and the lateral no-slip constraints of all wheels. A preintegration model and analytical Jacobians are developed for efficient filtering and calibration. An observability analysis of the linearized VIWO system shows that a drive-only model makes all steering offsets unobservable, whereas the proposed redundant model restores their observability. The analysis also identifies four standard VINS unobservable directions and three additional directions associated with the arbitrary placement of the odometry reference frame. Furthermore, we characterize several degenerate motions, including zero yaw rate, constant steering, and a non-rolling wheel, and derive the corresponding excitation conditions for the thirteen wheel intrinsics that remain after fixing the odometry frame reference. The performance of the proposed system has been demonstrated in both simulation and real-world experiments on a 4WIS4WID mobile robot.

0.21