CS Paper Radar

Emergency Obstacle Avoidance Maneuvers in Differential-Drive Mobile Robots

Kautik Mandve, Nilay Kant

cs.RO eess.SY ·submitted 2026-10-04 23:19 UTC · v1

Abstract

Emergency obstacle avoidance requires a mobile robot to brake or change its heading within the available distance. This paper investigates the dependence of maneuver performance and odometric error on approach speed for a differential-drive robot. A footprint-clearance analysis and a normalized wheel-motion index provide a kinematic description of five braking and turning maneuvers. The principal experiment comprises 540 block-randomized trials on tile, of which 539 are retained, at commanded approach speeds of 45, 55, and 65 cm/s. An overhead camera provides an independent pose reference. When encoder, gyro, and camera heading changes are evaluated over complete motion records, the mean encoder discrepancy increases by 4.7-5.1 degrees for the two reverse-spin maneuvers between the lowest and highest speeds; the arc and brake-assisted pivot change by less than 0.4 degrees. Larger encoder discrepancy is associated with lower avoidance success after adjustment for distance, speed, maneuver, day, and turn direction. Gyro discrepancies remain approximately 3 degrees for the reverse spins. Estimated reaction distances for 90% success and their uncertainty quantify the maneuver trade-offs. The results support speed-specific empirical characterization of emergency maneuvers and distinguish encoder error from recovery motion and measurement-window mismatch.

Closest papers

Nearest neighbours by meaning across the whole index.

FutureRay: Control-Aligned Future Range for Agile Quadruped Navigation

cs.RO ·2026-09-26 ·Tianhao Zang, Shanze Wang, Ziqian Wang, Liyou Luo, Zihan Liu +2 more
similarity 0.59
Abstract · 8 pages

Moving obstacles can block a previously clear route while a quadruped robot executes a motion command. We investigate whether predicting changing clearance improves navigation when motion selection accounts for the robot footprint and the time needed to react and brake. We present FutureRay, which predicts ranges across viewing directions and future times, together with encounter risk, from depth-derived range history and observable robot motion. Training emphasizes near-term clearance and penalizes errors that overstate available space. A local planner queries the same forecast for candidate headings and combines it with current observations to check clearance around the robot footprint. Model-based reaction--braking limits guide speed selection, and the resulting velocity commands are passed to a fixed locomotion policy. In paired evaluations on 60 static and dynamic simulation scenes, FutureRay achieves 93.3% completion, compared with 75.0% for current-range persistence and 80.0% for Cartesian Kalman rollout, with perception, planning, and locomotion held fixed. FutureRay also records fewer collisions than both baselines. Qualitative trials on a physical quadruped show avoidance initiated while an obstacle is approaching the route, followed by renewed goal progress. These results show that joint range and encounter-risk prediction can improve obstacle avoidance without retraining the locomotion policy.

0.25

High-Precision Docking of Differential-Drive Mobile Robots Through LiDAR and Vision Collaboration

cs.RO ·2026-11-18 ·Zaide Zhang, Zheyuan Zhang
similarity 0.58
Abstract

Precise docking requires a differential-drive robot to correct lateral offset through coupled rotation and translation within a short approach distance. We combine global navigation with terminal control using complementary LiDAR and visual observations. A line fitted to the cabinet front gives normal distance and heading. An AprilTag identifies the workstation; intersecting its center ray with the LiDAR plane determines tangential position. Taught observations define the docking reference and can cancel repeatable fixed biases under unchanged mounting and geometry. Lateral pre-alignment and continuous visual servoing coordinate the approach, with predictive stopping to account for low-speed actuation lag. Across two sessions using the same navigation and docking code at five workstations on Robot 2, all 111 tasks completed, including 101 on the first attempt. Relative to the taught observations, onboard longitudinal, lateral and heading residual root-mean-square values were 1.51 mm, 5.93 mm and 0.238 degrees, respectively. Joint acceptance within plus or minus 10 mm per position axis and plus or minus 1 degree heading was 96.4% (107/111), or 95.5% (106/111) with a plus or minus 0.5 degree heading limit.

0.34

Path-Following Control and Terramechanics Analysis for Planetary Rovers Under Wheel-to-Wheel Traction Asymmetry

cs.RO ·2026-09-30 ·Ryuya Matsuoka, Keisuke Takehana, Kentaro Uno, Toshinori Kuwahara, Kazuya Yoshida
published similarity 0.58
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

This paper proposes a control strategy for path following that is model-free and relies solely on deceleration for skid-steering planetary rovers navigating deformable loose terrain under continuously imposed traction asymmetry. While conventional controllers that are based on kinematics frequently cause slip-sinkage entrapment by accelerating the wheels during path correction, the proposed approach prevents this failure by setting an upper limit on the maximum commanded velocity. Heading correction is achieved solely through the selective deceleration of the outer wheels, which are located on the outside of the turn, driving them into a negative slip regime to act as a mechanical anchor. The system was evaluated using the four-wheel independent-drive rover EX1 under an asymmetric wheel configuration with different left and right grouser heights that induces significant deviations from the path. Experimental results demonstrate that this deceleration-only control successfully suppresses accumulated lateral drift across various velocity regimes up to 0.7 m/s without causing sinkage. Crucially, direct force measurements from onboard multi-axis sensors provide important empirical evidence of the underlying terramechanics, proving that the targeted deceleration establishes dynamic load equalization across the chassis and completely restores the native thrust capability of the opposite driving wheel.

0.37

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.58
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18

Observability Analysis and Online Calibration of Visual-Inertial-Wheel Odometry for 4WIS4WID Mobile Robots

cs.RO ·2026-09-29 ·Branimir Ćaran, Vladimir Milić, Bojan Šekoranja, Bojan Jerbić
similarity 0.58
Abstract · This work has been submitted to the IEEE for possible publication. Copyright may be transferred without notice, after which this version may…

In this paper, we present a visual-inertial-wheel odometry (VIWO) framework with online calibration for four-wheel independently steered and driven (4WIS4WID) mobile robots. We derive a 2D odometry model directly from the four driving velocities and steering angles, using both the longitudinal rolling constraints and the lateral no-slip constraints of all wheels. A preintegration model and analytical Jacobians are developed for efficient filtering and calibration. An observability analysis of the linearized VIWO system shows that a drive-only model makes all steering offsets unobservable, whereas the proposed redundant model restores their observability. The analysis also identifies four standard VINS unobservable directions and three additional directions associated with the arbitrary placement of the odometry reference frame. Furthermore, we characterize several degenerate motions, including zero yaw rate, constant steering, and a non-rolling wheel, and derive the corresponding excitation conditions for the thirteen wheel intrinsics that remain after fixing the odometry frame reference. The performance of the proposed system has been demonstrated in both simulation and real-world experiments on a 4WIS4WID mobile robot.

0.21

Tutorial: Vision-Based Formation Control with Differential-Drive Robots

cs.RO ·2026-11-08 ·Christian Marowski, Byung-Cheol Min
code/data similarity 0.57
Abstract

This tutorial presents a step-by-step introduction to multi-robot formation control using differential- drive robots, an overhead camera, and Python. ArUco markers are used to estimate robot positions and orientations, while desired pairwise displacement vectors define a circular formation. By comparing measured and desired relative positions, the controller computes movement vectors that are converted into differential-drive wheel commands, with basic proximity-sensor-based obstacle avoidance. The tutorial guides readers through hardware and software setup, robot pose estimation, formation geometry, feedback control, system integration, and formation-error evaluation. Motivated by the need to bridge the gap between theoretical understanding and practical implementation in robotics education, we emphasize how mathematical concepts are translated into coordinated behaviors on physical robots. Although the implementation uses a specific robotic platform, the underlying perception and formation-control principles can be adapted to other differential-drive robots and simulation environments. The accompanying open-source GitHub repository provides the Python implementation, setup instructions, and demonstrations to support hands-on learning and further exploration of multi-robot systems.

0.42

OcclusionCBF: Backup Control Barrier Functions for Safe Navigation Among Hidden Dynamic Obstacles

cs.RO eess.SY ·2026-09-06 ·Taekyung Kim, Hun Kuk Park, Renya Wada, Nikolay Atanasov, Shumon Koga +1 more
code/data similarity 0.57
Abstract · The first two authors contributed equally to this work. Project page: https://www.taekyung.me/occlusion-cbf

Robots navigating under occlusion may enter states from which no admissible input can avoid a dynamic obstacle once it becomes visible. We present OcclusionCBF, a safety filter that extends backup control barrier functions to reachable-occupancy predictions for potentially hidden dynamic obstacles in occluded regions. The method certifies a prescribed backup rollout against collision-inflated occupancy and a verified terminal set, yielding affine constraints for minimally invasive quadratic-program filtering. We establish recursive feasibility of the resulting safety filter, and collision avoidance for every hidden-obstacle motion covered by the occupancy prediction. Randomized benchmarks, MetaUrban simulations, and hardware experiments demonstrate improved task success over reactive and occlusion-aware predictive baselines with millisecond-scale computation.

0.40

Mapless, Stabilizing, and Anti-Stuck Flipper Control for Articulated Tracked Robots

cs.RO ·2026-10-09 ·Valentýn Číhala, Pavel Sarga, Martin Pecka, Tomáš Svoboda, Karel Zimmermann
similarity 0.57
Abstract · 8 pages, 3 figures and 2 tables

Nearly every autonomous or semi-autonomous flipper controller assumes access to an elevation map of the terrain under and in front of the robot. The terrain beneath the chassis is occluded in the sensors, so the map is remembered through odometry integration, whose drift corrupts it. We present Stabilizing Anti-Stuck (SAS), a mapless controller that combines a stabilization term for body roll and pitch with an anti-stuck term that frees the robot when it gets stuck. As input, SAS uses the IMU, the flipper joint angles, and a motion cue that only tells whether the robot is moving. The cue is computed over a short window and never accumulated, so SAS does not inherit the odometry-integration drift that corrupts the map. We deploy SAS on a tracked robot with four flippers and evaluate it against manual teleoperation and prior flipper controllers in a large comparison, both in simulation and on a real obstacle. In simulation and on the real robot, SAS achieves traversal quality comparable to state-of-the-art map-based controllers. On a log hidden in tall grass, invisible to the LiDAR, the best map-based controller gets stuck while SAS traverses the hidden obstacle without a problem.

0.34