CS Paper Radar

High-Precision Docking of Differential-Drive Mobile Robots Through LiDAR and Vision Collaboration

Zaide Zhang, Zheyuan Zhang

cs.RO ·submitted 2026-11-18 10:28 UTC · v1

Abstract

Precise docking requires a differential-drive robot to correct lateral offset through coupled rotation and translation within a short approach distance. We combine global navigation with terminal control using complementary LiDAR and visual observations. A line fitted to the cabinet front gives normal distance and heading. An AprilTag identifies the workstation; intersecting its center ray with the LiDAR plane determines tangential position. Taught observations define the docking reference and can cancel repeatable fixed biases under unchanged mounting and geometry. Lateral pre-alignment and continuous visual servoing coordinate the approach, with predictive stopping to account for low-speed actuation lag. Across two sessions using the same navigation and docking code at five workstations on Robot 2, all 111 tasks completed, including 101 on the first attempt. Relative to the taught observations, onboard longitudinal, lateral and heading residual root-mean-square values were 1.51 mm, 5.93 mm and 0.238 degrees, respectively. Joint acceptance within plus or minus 10 mm per position axis and plus or minus 1 degree heading was 96.4% (107/111), or 95.5% (106/111) with a plus or minus 0.5 degree heading limit.

Closest papers

Nearest neighbours by meaning across the whole index.

Online Joint Calibration of Steering Offset and Planar LiDAR Extrinsics for Wheeled Mobile Robots

cs.RO ·2026-08-27 ·Subodh Mishra, Arindam Dhar, Suprotim Majumdar, Naveen Arulselvan
similarity 0.63
Abstract

Accurate steering sensing and LiDAR-to-vehicle extrinsics are crucial for reliable path tracking in warehouse mobile robots (WMRs); miscalibration often leads to snaking, weaving, and elevated cross-track error (CTE). In practice, steering ``zero'' is commonly set manually (e.g., eyeballing straightness via a PS4 joystick), while LiDAR extrinsics are assumed from CAD and may drift after maintenance. Such static, manual procedures frequently cause miscalibration in safety-critical environments. This paper presents an Extended Kalman Filter (EKF)--based method for online estimation of steering offset and planar LiDAR extrinsics within a bicycle-kinematics model, providing a principled alternative to manual calibration. Experiments on real datasets show that correcting steering offset reduces CTE substantially, validating the effectiveness of the proposed approach.

0.29

DCLP++: Learning to Navigate with Footprint Clearance and Relative Motion

cs.RO ·2026-09-08 ·Shanze Wang, Wei Zhang
hot direction similarity 0.63
Abstract · 5 pages

We present DCLP++, a local navigation frameworkthat uses footprint clearance as the geometric basis for studying relative motion features in dynamic environments. Each valid LiDAR return is mapped to its shortest Euclidean distance from the filled robot footprint before reciprocal encoding, replacing distance from the sensor with distance to the occupied body. Radial measurementsor simulated planar relative velocities provide short-horizon features without static-dynamic labels in the policy input. A preliminary study uses a rectangular robot with a speed limit of 1 m/s among 20 moving obstacles. On 100 fixed validation tasks, two selected training seeds yield mean success rates of 42% with sensor rangeand 70% with footprint clearance after 200,000 environment steps.Motion variants show mixed additional gains. These results supportthe clearance-based observation in the evaluated setting; reliable motion benefits and transfer across robots require further evaluation.

0.52

A comparative study on the accuracy & repeatability of mobile robotic platforms for the delivery of precision NDE measurement

cs.RO ·2026-09-03 ·SeyedMohammadAmin Nabi Pour, S. Gareth Pierce, Randika Vithanage, Ehsan Mohseni, David Carswell +1 more
similarity 0.61
Abstract

Mobile robotic platforms offer a flexible alternative to fixed manipulators for non-destructive evaluation (NDE) of large aerospace structures, but their base-positioning accuracy and how that accuracy should inform deployment have not been assessed under a common, externally referenced protocol. This work presents a laser tracker-based evaluation workflow (ground truth approximately 6 micrometers) that measures the static and segmented trajectory positioning accuracy of five commercial mobile platforms (KUKA KMP-1500, KUKA KMR, MiR250, Boston Dynamics Spot, Clearpath Husky) under a common protocol. A coupled multi-corner calibration recovers the laser-to-robot transformation and reflector offsets; ordinary least squares over all poses is used, with robust estimation retained only as a blunder check. Static positioning accuracy ranged from a median of 8.2 mm (KMP-1500) to 63.5 mm (Spot), with the wheel-odometry-only Husky uncalibratable. Dynamic path following was characterised by cross-track error; the component was insensitive to temporal alignment, which ranged from 6.9 mm (KMP-1500) to 112.1 mm (Spot). Both accuracy and calibratability tracked localisation capability, from the newest LiDAR SLAM platform to map-free visual odometry. No configuration meets the 0.2 to 1.0 mm aerospace NDE tolerance from the base alone; the results are framed as a design input that sizes the supplementary sensing each platform requires: roughly one order of magnitude for the best platform and nearly two for the worst, providing a reproducible basis for platform selection rather than a feasibility claim.

0.16

Lightweight and Resource-Efficient Perception for Robotic Guide Dogs

cs.DC cs.CV ·2026-10-02 ·Jinse Kwon, Yoojin Lim, Choonghan Lee, Yongseung Yu, Yongin Kwon +1 more
publishedbenchmark similarity 0.59
Abstract · accepted in ACCV 2026

Robotic guide dogs should understand their surroundings, objects, and potential risks. Prior research has focused on raw sensor data from cameras and 2D or 3D LiDAR, which precisely measure distance points rather than provide a semantic understanding of the scene. While these physical measurements are effective for robot-centric collision avoidance and robot safety, they are not suitable for human-centric guidance. The system should recognize the type and relevance of obstacles and explain them, clearly and actionably, in terms of their spatial relation to the user. We present complete on-device perception modules that fuse a 360 camera and a 2D LiDAR for reliable collision avoidance, with moving-object detection and tracking for human-centric guidance. Finally, in walking-impossible situations, a vision--language model delivers pathway explanations as a safety mechanism to reduce user anxiety. In experiments, verification of fused 360 camera--LiDAR depth shows reliable near-range perception but inherent mid-range bias, while the system as a whole sustained real-time performance under 55 W. On the real-world egocentric GuideDogQA benchmark, our system achieved 83.8\% accuracy, compared with 67.1\% for GPT-4o. These results demonstrate that practical human-centric guidance with real-time on-device inference is feasible even on quadrupeds.

0.21

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.59
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18

Emergency Obstacle Avoidance Maneuvers in Differential-Drive Mobile Robots

cs.RO eess.SY ·2026-10-04 ·Kautik Mandve, Nilay Kant
similarity 0.58
Abstract

Emergency obstacle avoidance requires a mobile robot to brake or change its heading within the available distance. This paper investigates the dependence of maneuver performance and odometric error on approach speed for a differential-drive robot. A footprint-clearance analysis and a normalized wheel-motion index provide a kinematic description of five braking and turning maneuvers. The principal experiment comprises 540 block-randomized trials on tile, of which 539 are retained, at commanded approach speeds of 45, 55, and 65 cm/s. An overhead camera provides an independent pose reference. When encoder, gyro, and camera heading changes are evaluated over complete motion records, the mean encoder discrepancy increases by 4.7-5.1 degrees for the two reverse-spin maneuvers between the lowest and highest speeds; the arc and brake-assisted pivot change by less than 0.4 degrees. Larger encoder discrepancy is associated with lower avoidance success after adjustment for distance, speed, maneuver, day, and turn direction. Gyro discrepancies remain approximately 3 degrees for the reverse spins. Estimated reaction distances for 90% success and their uncertainty quantify the maneuver trade-offs. The results support speed-specific empirical characterization of emergency maneuvers and distinguish encoder error from recovery motion and measurement-window mismatch.

0.31

Learning Wheel Motion Uncertainty for Degeneracy-Aware LiDAR-Inertial Odometry on Quadrupedal Wheel-Legged Robots

cs.RO ·2026-10-19 ·Hairuo Wei, Yunfan Ren, Renda Yang, Qiangsheng Huang, Zhongyu Li
similarity 0.58
Abstract

Wheel kinematics can support odometry for quadrupedal wheel-legged robots when LiDAR geometry provides weak motion constraints. However, slip and contact loss make rolling predictions unreliable, and contact state alone cannot determine their reliability across motion directions. We propose a tightly coupled LiDAR-inertial-kinematic odometry framework that retains analytical rolling predictions and learns per-wheel, direction-dependent process covariances from proprioceptive history. The estimator maintains moving wheel-center states, allowing the learned uncertainty to regulate the influence of rolling predictions through forward-kinematic corrections. Degeneracy-aware projection (DAP) complements this mechanism by suppressing LiDAR constraints along geometrically weak directions. The learned covariance network (CovNet) is trained through a differentiable filter using simulated velocity supervision and deployed on the real robot without fine-tuning. On the six room sequences with the highest degeneracy ratios in our indoor dataset, the method reduces mean per-sequence position root mean square error (RMSE) by 66.2% relative to FAST-LIO2 and by 31.0% relative to a fixed-covariance variant. In a severely degenerate corridor run, it achieves an endpoint position error of 0.198 m, compared with 7.531 m for FAST-LIO2. These results demonstrate robust odometry under challenging geometric and wheel-motion conditions. We plan to publicly release our code and multimodal dataset. Project website: https://weihairuo.github.io/wheel-motion-uncertainty/

0.29

NavPatch: Evidence-Guided Object-Level Costmap Correction with Vision-Language Models

cs.RO ·2026-09-13 ·Shiji Sun, Xingyu Tao, Hao Wang, Ling Wang, Zhengyi Chen
similarity 0.58
Abstract

Mobile robots typically rely on geometric maps for obstacle avoidance and path planning, but the resulting obstacle representation does not always match how an object should affect navigation. A low lying cable may be missed, a flexible curtain may create spurious blockage, and a traffic cone may require an exclusion region larger than its observed footprint. We present NavPatch, an object level correction layer that assigns ADD, REMOVE, or EXTEND to navigation relevant object categories through periodic scene understanding with a vision-language model. Open vocabulary grounding localizes object instances, and LiDAR and RGB-D observations provide 3D support. Observation quality filtering and cross frame maintenance determine when each correction patch is committed, replaced, or revoked. In 50 real robot trials across five layouts, NavPatch achieves an overall success rate of 86.0%. An ablation study of four configurations with 200 runs in total shows that NavPatch improves the success rate from 70.0% to 86.0% and reduces the false commit rate from 68.4% to 40.7% compared with updates based only on the current observation.

0.23