CS Paper Radar

Inertial Steering and Motion Prediction of Tracked Vehicles on Low-Adherence Surfaces

Mathis Turgeon-Roy, Mohamed Ounally, Veronica Vannini, Olivier Roy, François Pomerleau

cs.RO eess.SY ·submitted 2026-10-28 20:50 UTC · v1

Abstract

Tracked vehicles are widely used in off-road applications, but their conventional motion models often rely on no-slip assumptions that become inaccurate on low-adherence surfaces. Rather than treating inertial effects arising from slip as a disturbance to be minimized, this work investigates how inertial effects arising from a moving mass can be deliberately exploited for steering on low-friction surfaces. A dynamic model for an articulated tracked vehicle with a passive trailer is developed, allowing inertial effects from trailer motion to be captured. The approach is experimentally evaluated on ice, where our dynamic model outperforms the kinematic baseline. We also propose a mixed dynamic-kinematic model to adapt predictions to both surface and situation by exploiting predictions from both methods. Finally, we demonstrate inertial steering on a mono-track vehicle without a conventional steering mechanism, showing that controlled movements of an internal mass can generate turning motion on ice. The resulting behavior can be predicted using the proposed dynamic model by representing the internal mass as a frictionless trailer, revealing the analogous dynamics between the two configurations. These results demonstrate the feasibility of inertial steering as an alternative steering mechanism for tracked vehicles operating in low-adherence environments.

Closest papers

Nearest neighbours by meaning across the whole index.

Steering Through Contact: A Finite-Support Motion Model for Single-Track Center-Articulated Robots

cs.RO ·2026-09-20 ·Mohamed Dhia Ounally, Nicolas Samson, Mathis Turgeon-Roy, Veronica Vannini, Johann Laconte +1 more
similarity 0.69
Abstract · 8 pages, 7 figures, 1 table

Trajectory planning and control in field robotics rely on predicting how propulsion and steering affect vehicle motion when contact points undergo slip. For articulated vehicles, the point-contact kinematic model (PCK) accounts for the linkage geometry but neglects the rotational resistance distributed along the contacts. We propose a finite-support quadratic model (FSQ) for single-track, center-articulated vehicles that incorporates this resistance through a quasi-static balance of lateral slip. Our approach generalizes the standard PCK formulation by relaxing the contact-point assumption. An exact reduction of the quadratic slip cost to contact moments gives a compact closed-form solution for real-time prediction of lateral velocity and yaw rate. We evaluate the proposed method in real-world experiments across asphalt, grass, ice, and mixed routes, using more than 7 km of data. For five-second predictions, FSQ reduces the weighted median translation and yaw errors by 53.5% and 68.9%, respectively, relative to PCK.

0.29

Slip-Induced Fall Suppression During Cornering for a Remotely Operated Motorcycle with a Rear-Wheel-Swing Mechanism

cs.RO eess.SY ·2026-10-15 ·Tadashi Sumioka, Kazushi Akimoto, Takuya Tsujimura, Sho Takayanagi, Kineo Tomura
similarity 0.63
Abstract · Journal papaer, 12 pages, 13 figures

Slip-induced falls when riding motorcycles are difficult to avoid even for expert riders and represent a major cause of single-vehicle accidents. Despite their prevalence, no practical solution has yet been proposed to suppress this phenomenon. We previously introduced a motorcycle model applicable to systems with both front- and rear- wheel steering. In this paper, we extend that model and formulate the suppression of slip-induced falls as an optimization problem that distributes assistive control inputs according to vehicle speed and road surface conditions. To evaluate the proposed method, we developed a remotely operated motorcycle and conducted experiments under two scenarios: slalom driving on a low-friction surface at 5.5 m/s, and turning maneuvers on synthetic ice to simulate driving over manholes on rainy days. The results demonstrate that our approach successfully suppresses falls under these challenging conditions.

0.25

Mapless, Stabilizing, and Anti-Stuck Flipper Control for Articulated Tracked Robots

cs.RO ·2026-10-09 ·Valentýn Číhala, Pavel Sarga, Martin Pecka, Tomáš Svoboda, Karel Zimmermann
similarity 0.61
Abstract · 8 pages, 3 figures and 2 tables

Nearly every autonomous or semi-autonomous flipper controller assumes access to an elevation map of the terrain under and in front of the robot. The terrain beneath the chassis is occluded in the sensors, so the map is remembered through odometry integration, whose drift corrupts it. We present Stabilizing Anti-Stuck (SAS), a mapless controller that combines a stabilization term for body roll and pitch with an anti-stuck term that frees the robot when it gets stuck. As input, SAS uses the IMU, the flipper joint angles, and a motion cue that only tells whether the robot is moving. The cue is computed over a short window and never accumulated, so SAS does not inherit the odometry-integration drift that corrupts the map. We deploy SAS on a tracked robot with four flippers and evaluate it against manual teleoperation and prior flipper controllers in a large comparison, both in simulation and on a real obstacle. In simulation and on the real robot, SAS achieves traversal quality comparable to state-of-the-art map-based controllers. On a log hidden in tall grass, invisible to the LiDAR, the best map-based controller gets stuck while SAS traverses the hidden obstacle without a problem.

0.34

A Novel Path-Tracking Algorithm for Automated Tractor-Trailer Forward and Backward Maneuvers

cs.RO eess.SY ·2026-09-18 ·Alexandre Lombard, Florent Perronnet, Théo Rigal, Nicolas Gaud, Abdeljalil Abbas-Turki
similarity 0.61
Abstract

Fully autonomous tractor-trailer systems are increasingly deployed in logistics, agriculture, and industrial environments, where precise and robust path-tracking capabilities are essential. However, the articulation between the tractor and the trailer introduces additional nonlinearities and significantly complicates lateral and longitudinal control, particularly during reversing maneuvers. This paper introduces a novel path-tracking algorithm specifically designed for articulated vehicles with a single trailer. The proposed method combines a lateral control law applied at the trailer level with a short-horizon predictive adjustment of the tractor steering angle, ensuring stable convergence toward the desired path in both forward and backward motion. The approach is geometry-based and requires no per-vehicle calibration or training. Simulation studies in a high-fidelity physics simulator show steady-state or final lateral errors of $0.02$--$0.05$~m on straight-line, circular, and reverse docking trajectories, which is of the same order of magnitude as, or lower than, the errors reported in the literature. Real-world experiments on a small-scale tractor--trailer robot, with the whole controller running on a low-cost microcontroller, further confirm the feasibility of the approach, with lateral errors below 13~mm during repeated reverse docking maneuvers despite a pose detection latency of about 200~ms.

0.10

Wheel-loader V-Cycle Automation with Deep Koopman MPC

cs.RO eess.SY ·2026-09-22 ·Armin Abdolmohammadi, Navid Mojahed, Dinesh Kumar, Bahram Ravani, Shima Nazari
similarity 0.60
Abstract · 8 pages, 4 figure

The repeated forward-reverse maneuvers performed by wheel loaders during earthmoving operations make them well suited for automation. However, the nonlinear dynamics of articulated vehicles and complex vehicle-terrain interactions limit the effectiveness of conventional model-based approaches. This paper presents a hierarchical framework that combines long-horizon geometric planning with data-driven predictive control for autonomous wheel-loader operation. A reduced-order articulated kinematic model is used to generate the maneuver geometry, where the forward and reverse trajectories are jointly optimized through a shared intermediate state. To capture the vehicle dynamics, two data-driven deep bilinear Koopman models are learned for the forward and reverse motions using data generated from high-fidelity simulations in Algoryx Dynamics. The learned Koopman representations are subsequently incorporated into a computationally efficient model predictive control (MPC) formulation for trajectory tracking. The resulting controller operates in real time within a 50-ms execution loop. High-fidelity simulation results demonstrate that the proposed end-to-end framework enables accurate and computationally efficient execution of wheel-loader V-cycle maneuvers, providing a promising approach toward autonomous operation of articulated heavy-duty machinery.

0.26

Data-Driven Predictive Control for Autonomous Vehicle Racing under Varying Friction

eess.SY cs.RO ·2026-11-16 ·Julius Beerwerth, Julius Tischbein, Bassam Alrifaee
code/data similarity 0.59
Abstract · 8 pages, 4 figures. Submitted to the 2027 European Control Conference (ECC). Code and data: https://github.com/bassamlab/multisurface-racing…

Data-driven predictive control (DPC) predicts future outputs by combining recorded input-output trajectory data such that the combined trajectory approximately matches a measured initial trajectory and tracks a provided reference. This paper investigates to what extent and under which conditions DPC using data pooled across operating conditions retains the prediction accuracy of DPC using data from the current operating condition. In autonomous vehicle racing, the tire-road friction varies between racetrack sections and tire sets. If the initial trajectory and the recorded data originate from different frictions, prediction accuracy of DPC degrades. Ensuring the frictions match requires knowing the friction during recording and estimating the current friction explicitly. Instead, we pool data recorded at different frictions. We compare the prediction accuracy of DPC using data recorded under the current friction (matched), a different friction (mismatched) and data pooled from both frictions. We evaluate in simulation and small-scale vehicle experiments in the Cyber-Physical Mobility Lab (CPM Lab). Our results show that pooled data keep the multi-step root-mean-square prediction error within 1.5 times that of matched data, whereas mismatched data increase it by a factor of 2.2 to 3.4. To assess how this prediction accuracy carries over to control, we evaluate the tracking error from the raceline in closed loop. In simulation, DPC with pooled data tracks comparably to nonlinear model predictive control (13.7 cm versus 13.3 cm) and close to DPC with matched data in the CPM Lab, differing by 0.1 cm on the low-friction tires (1.6 cm versus 1.5 cm) and by 0.2 cm on the high-friction tires (0.9 cm versus 1.1 cm). DPC thus provides partial adaptation to varying friction, without a dedicated adaptation method.

0.58

IMU-Centric Moving Horizon Estimation for Lateral Dynamics Estimation Across Vehicles and Grip Conditions

eess.SY cs.RO ·2026-09-09 ·Seuffo Akouan ha Ngoune, Alessandro Toschi, Paolo Burgio, Marko Bertogna
publishedcode/data similarity 0.58
Abstract · Accepted at the 29th IEEE International Conference on Intelligent Transportation Systems (ITSC 2026). 8 pages, 6 figures

Accurate estimation of lateral vehicle dynamics near the adhesion limit is important for stability control and high-performance driving, but lateral velocity is rarely measured directly because sensors such as optical sensors are costly. This paper presents an inertial measurement unit (IMU)-centric Moving Horizon Estimation framework that reconstructs lateral velocity using standard onboard signals, without relying on exteroceptive odometry or detailed tire-parameter tuning. Experimental validation on human-driven sports cars and an autonomous open-wheel race car across tracks, maneuvers, and conditions demonstrates accurate and robust lateral velocity and lateral acceleration estimates. The proposed framework is available at https://github.com/Aseuffo/IMU-Centric-MHE

0.48

LQR-ArUco Fusion: Robust Hierarchical Control for Navigation and Asymmetric Manipulation in Two-Wheeled Robots

cs.RO eess.SY ·2026-09-28 ·Anupam Chatterjee, Arpita Kumari
published similarity 0.58
Abstract · 6 pages, 9 figures, 2 tables. Accepted for presentation at the 2026 IEEE International Conference on Intelligent Navigation and Systems (CIN…

We propose a hierarchical control framework to address severe dynamic instabilities and navigational drift that arise when a two-wheeled inverted pendulum (TWIP) robot attempts asymmetric object manipulation. While two-wheeled platforms are highly manoeuvrable, their constant balancing adjustments make onboard odometry highly unreliable for precise navigation. Furthermore, the addition of a side-mounted robotic arm introduces unactuated lateral roll moments when a payload is lifted, a challenge heavily compounded on uneven terrain. To solve these coupled problems, our architecture divides the workload. An offboard vision system tracks overhead ArUco markers to provide high-latency global waypoint navigation, bypassing odometry drift. Simultaneously, a low-latency onboard control loop rejects active physical disturbances using inertial and encoder data. In our physical experiments, this dual-loop approach enabled the custom-built robot to navigate accurately, reject transient impacts from speed bumps, adapt to a dynamic seesaw ramp, and carry a payload securely without falling over its narrow wheelbase.

0.43