CS Paper Radar

Slip-Induced Fall Suppression During Cornering for a Remotely Operated Motorcycle with a Rear-Wheel-Swing Mechanism

Tadashi Sumioka, Kazushi Akimoto, Takuya Tsujimura, Sho Takayanagi, Kineo Tomura

cs.RO eess.SY ·submitted 2026-10-15 01:43 UTC · v1

Abstract

Slip-induced falls when riding motorcycles are difficult to avoid even for expert riders and represent a major cause of single-vehicle accidents. Despite their prevalence, no practical solution has yet been proposed to suppress this phenomenon. We previously introduced a motorcycle model applicable to systems with both front- and rear- wheel steering. In this paper, we extend that model and formulate the suppression of slip-induced falls as an optimization problem that distributes assistive control inputs according to vehicle speed and road surface conditions. To evaluate the proposed method, we developed a remotely operated motorcycle and conducted experiments under two scenarios: slalom driving on a low-friction surface at 5.5 m/s, and turning maneuvers on synthetic ice to simulate driving over manholes on rainy days. The results demonstrate that our approach successfully suppresses falls under these challenging conditions.

Comment
Journal papaer, 12 pages, 13 figures

Closest papers

Nearest neighbours by meaning across the whole index.

Inertial Steering and Motion Prediction of Tracked Vehicles on Low-Adherence Surfaces

cs.RO eess.SY ·2026-10-28 ·Mathis Turgeon-Roy, Mohamed Ounally, Veronica Vannini, Olivier Roy, François Pomerleau
similarity 0.63
Abstract

Tracked vehicles are widely used in off-road applications, but their conventional motion models often rely on no-slip assumptions that become inaccurate on low-adherence surfaces. Rather than treating inertial effects arising from slip as a disturbance to be minimized, this work investigates how inertial effects arising from a moving mass can be deliberately exploited for steering on low-friction surfaces. A dynamic model for an articulated tracked vehicle with a passive trailer is developed, allowing inertial effects from trailer motion to be captured. The approach is experimentally evaluated on ice, where our dynamic model outperforms the kinematic baseline. We also propose a mixed dynamic-kinematic model to adapt predictions to both surface and situation by exploiting predictions from both methods. Finally, we demonstrate inertial steering on a mono-track vehicle without a conventional steering mechanism, showing that controlled movements of an internal mass can generate turning motion on ice. The resulting behavior can be predicted using the proposed dynamic model by representing the internal mass as a frictionless trailer, revealing the analogous dynamics between the two configurations. These results demonstrate the feasibility of inertial steering as an alternative steering mechanism for tracked vehicles operating in low-adherence environments.

0.21

Stability Control for Real World Testing in Autonomous Racing

cs.RO eess.SY ·2026-08-18 ·Phillip Pitschi, Simon Sagmeister, Frederik Werner, Markus Lienkamp, Boris Lohmann
publishedcode/data similarity 0.58
Abstract · Accepted at IEEE ITSC 2026

Controlling an autonomous vehicle at the limits of handling is a challenging task. Due to external influences, such as road conditions or weather, a vehicle can easily become unstable. Since most control algorithms assume stable vehicle behavior, they might fail in these situations. Especially when operating expensive vehicles without a safety driver on board, as in autonomous racing, this poses a significant challenge. To enable safe operation at the vehicle's dynamic limits, we present a comprehensive stability control system that safeguards motion control algorithms in autonomous driving. The proposed system consists of an electronic stability control (ESC), a slip control (SC), and a countersteer system (CS), which collectively adapt steering and brake commands from the motion controller to maintain vehicle stability. We validate our approach through both simulation and experiments on a real-world, full-scale vehicle. The results show that the stability control system maintains vehicle stability in critical situations and extends the operational feasible region. To simplify integration, we provide an open-source implementation at github.com/TUMFTM/tam-stability-control.

0.44

SCET-CBF: Speed-Calibrated Soft Guidance for One-Step Dynamic Navigation

cs.RO ·2026-10-24 ·Xiaoyu Han, Dongkun Han
similarity 0.56
Abstract · 9 pages, 6 figures

Control barrier functions (CBFs) support collision avoidance, yet dense dynamic encounters can leave a vehicle with no feasible command. Geometric refinements and soft constraints help preserve motion choices. Using these choices also requires accounting for the vehicle's changing turning response. For a steering-limited bicycle, braking can lower closing speed while slowing the lateral motion needed before an obstacle arrives. We propose SCET-CBF, a speed-calibrated soft guidance law for one-step dynamic navigation. A short lateral escape maneuver gives an allowable approach speed. Its speed derivative allows a quadratic program to weigh both effects of braking when choosing acceleration and steering. Soft penalties accommodate competing obstacle preferences within the input set permitted by segment and braking constraints. We derive the guidance and establish protection over each accepted motion segment, together with conditional braking invariance for a single obstacle. On 2500 paired tasks with a 60 s deadline, SCET achieves 72.8% completion, compared with 49.8% for CBF/velocity-obstacle control and 69.8% for an enhanced 1 s CBF-MPC. At 100 obstacles, SCET and the enhanced MPC complete 52.4% and 33.6% of tasks. Paired studies identify the contributions of speed feedback and early activation. Further evaluations examine the operating range under lateral acceleration limits and bounded motion and execution errors.

0.13

Steering Through Contact: A Finite-Support Motion Model for Single-Track Center-Articulated Robots

cs.RO ·2026-09-20 ·Mohamed Dhia Ounally, Nicolas Samson, Mathis Turgeon-Roy, Veronica Vannini, Johann Laconte +1 more
similarity 0.55
Abstract · 8 pages, 7 figures, 1 table

Trajectory planning and control in field robotics rely on predicting how propulsion and steering affect vehicle motion when contact points undergo slip. For articulated vehicles, the point-contact kinematic model (PCK) accounts for the linkage geometry but neglects the rotational resistance distributed along the contacts. We propose a finite-support quadratic model (FSQ) for single-track, center-articulated vehicles that incorporates this resistance through a quasi-static balance of lateral slip. Our approach generalizes the standard PCK formulation by relaxing the contact-point assumption. An exact reduction of the quadratic slip cost to contact moments gives a compact closed-form solution for real-time prediction of lateral velocity and yaw rate. We evaluate the proposed method in real-world experiments across asphalt, grass, ice, and mixed routes, using more than 7 km of data. For five-second predictions, FSQ reduces the weighted median translation and yaw errors by 53.5% and 68.9%, respectively, relative to PCK.

0.29

Path-Following Control and Terramechanics Analysis for Planetary Rovers Under Wheel-to-Wheel Traction Asymmetry

cs.RO ·2026-09-30 ·Ryuya Matsuoka, Keisuke Takehana, Kentaro Uno, Toshinori Kuwahara, Kazuya Yoshida
published similarity 0.55
Abstract · Author's version of a manuscript accepted at the International Conference on Space Robotics 2026 (iSpaRo 2026). (c) IEEE

This paper proposes a control strategy for path following that is model-free and relies solely on deceleration for skid-steering planetary rovers navigating deformable loose terrain under continuously imposed traction asymmetry. While conventional controllers that are based on kinematics frequently cause slip-sinkage entrapment by accelerating the wheels during path correction, the proposed approach prevents this failure by setting an upper limit on the maximum commanded velocity. Heading correction is achieved solely through the selective deceleration of the outer wheels, which are located on the outside of the turn, driving them into a negative slip regime to act as a mechanical anchor. The system was evaluated using the four-wheel independent-drive rover EX1 under an asymmetric wheel configuration with different left and right grouser heights that induces significant deviations from the path. Experimental results demonstrate that this deceleration-only control successfully suppresses accumulated lateral drift across various velocity regimes up to 0.7 m/s without causing sinkage. Crucially, direct force measurements from onboard multi-axis sensors provide important empirical evidence of the underlying terramechanics, proving that the targeted deceleration establishes dynamic load equalization across the chassis and completely restores the native thrust capability of the opposite driving wheel.

0.37

Emergency Obstacle Avoidance Maneuvers in Differential-Drive Mobile Robots

cs.RO eess.SY ·2026-10-04 ·Kautik Mandve, Nilay Kant
similarity 0.54
Abstract

Emergency obstacle avoidance requires a mobile robot to brake or change its heading within the available distance. This paper investigates the dependence of maneuver performance and odometric error on approach speed for a differential-drive robot. A footprint-clearance analysis and a normalized wheel-motion index provide a kinematic description of five braking and turning maneuvers. The principal experiment comprises 540 block-randomized trials on tile, of which 539 are retained, at commanded approach speeds of 45, 55, and 65 cm/s. An overhead camera provides an independent pose reference. When encoder, gyro, and camera heading changes are evaluated over complete motion records, the mean encoder discrepancy increases by 4.7-5.1 degrees for the two reverse-spin maneuvers between the lowest and highest speeds; the arc and brake-assisted pivot change by less than 0.4 degrees. Larger encoder discrepancy is associated with lower avoidance success after adjustment for distance, speed, maneuver, day, and turn direction. Gyro discrepancies remain approximately 3 degrees for the reverse spins. Estimated reaction distances for 90% success and their uncertainty quantify the maneuver trade-offs. The results support speed-specific empirical characterization of emergency maneuvers and distinguish encoder error from recovery motion and measurement-window mismatch.

0.31

Floor Friction Assessment from Robot Tire-Surface Interaction

cs.RO ·2026-10-24 ·Kulbhushan Komarraju, Nathaniel Pearson, Yu Gu, Jason Gross
similarity 0.54
Abstract · 11 pages and 14 figures; Extended abstract submitted to IEEE/ION PLANS 2027, under review

Floor traction influences wheel-slip behavior, dead-reckoning accuracy, and the navigation performance of wheeled mobile robots that rely on wheel odometry. As these robots become increasingly common in GNSS-denied indoor environments, including automated manufacturing and retail facilities, their onboard measurements could also be used to characterize floor conditions and improve localization. In this study, a skid-steer robot was driven over five floor surfaces with distinct traction characteristics using commanded velocity profiles designed to induce wheel slip through repeated acceleration and direction reversal. Differences between the body velocity estimated from inertial sensing and the velocity obtained from wheel odometry were evaluated using the integrated relative-velocity error, phase-derived wheel-to-body response delay, and velocity-reversal response delay. Welch power spectral density analysis was additionally applied to characterize the frequency distribution of the velocity mismatch during positive and negative acceleration. Band-integrated spectral power, spectral centroid, and spectral decay rate were extracted from each recording and evaluated using linear discriminant analysis and multiclass classification. The response-delay measurements produced consistent surface-dependent trends, with the longest delays observed on soap and the shortest delays observed on carpet. The spectral features also provided clear separation among the tested surfaces, achieving a balanced classification accuracy of 97.1% under recording-level cross-validation. These results demonstrate that both the magnitude and frequency domain characteristics of wheel-to-body velocity mismatch contain useful information about tire-surface interactions. Such information could support surface recognition and the development of slip-aware wheel-odometry weighting within robot state-estimation frameworks.

0.25

SceneFactory-3D: Lifting 2D Traffic Scenes into 3D Physical Counterfactuals for Scalable Physically Grounded Safety Evaluation

cs.RO cs.MA ·2026-10-02 ·Yicheng Zhu, Linfeng Tian, Tianmu Zhao, Yang Chen, Fan Zuo +2 more
code/data similarity 0.53
Abstract

Scalable driving simulators typically execute vehicle commands using prescribed behavioral or kinematic rules, overlooking the physics of tire-road interfaces, thereby limiting their ability to capture how adverse road and environmental conditions alter vehicle execution and propagate through traffic. To address this limitation, we present SceneFactory-3D, a GPU-batched, physics-grounded multi-agent driving simulator. Vehicles execute acceleration and steering commands via suspension- and friction-limited forces evaluated at each wheel-contact point. Spatially varying friction, per-world 3D heightfields, gravity, and rigid contact consistently govern wheel motion and chassis collisions. Per-world terrain isolation and GPU batching enable SceneFactory-3D to run matched physical counterfactuals in parallel: traffic scenario setup and vehicle controllers remain fixed while only the road condition changes, enabling the resulting closed-loop effects to be evaluated across parallel worlds. To demonstrate the advantage of the SceneFactory-3D-enabled counterfactual evaluation, we conduct an empirical study on vehicle controllers' sensitivity to road conditions. We study three learned-policy families on 1,024 matched 12-vehicle worlds per condition, and two classical planners on a shared 32-world subset, across 21 friction and grade conditions. When friction drops from 1.0 to 0.18, the share of vehicles that clear the work zone safely falls by 6 to 90 percentage points across learned policies (18-19 for classical planners), and near-collision situations become more frequent for every learned policy. Code: https://github.com/SmallWorldLab/SceneFactory_3D

0.32