CS Paper Radar

Direct Electromechanical Actuation of the Shift Drum in Non-Synchronized Motorcycle Transmissions: From Actuator Sizing and Electronics Design to Closed-Loop Position Control

Johannes Stockhammer

eess.SY ·submitted 2026-10-12 20:47 UTC · v1
unusual

Abstract

This thesis presents the direct electromechanical actuation of the shift drum in a non-synchronized motorcycle transmission. A DC motor drives the shift drum through a self-locking worm gear, so the entire foot shift mechanism is eliminated. As a reference, 84 manual gear changes of a large-displacement series-production motorcycle were measured on a chassis dynamometer; the mean shift time is 80 ms for upshifts and 92 ms for downshifts. The system design covers the complete chain from the mechanics to the software. The actuator motor is sized from inertia, friction and gear ratio. A dedicated shift controller is developed with supply filtering, signal conditioning for the position sensor and the incremental encoder, an H-bridge motor driver and a custom circuit board based on a SAMD21 microcontroller. The embedded firmware implements position control of the shift drum with a proportional controller, without inner speed or current loops. On a gearbox test rig, a gear change is completed in less than 80 ms without overshoot in a single measurement, below the mean of the manual reference shifts. The analysis reveals a trade-off in the choice of the worm gear ratio: at a ratio of 30, about 93% of the motor torque is needed to accelerate the motor shaft and the worm. A ratio of about 8 halves the required torque, but the worm gear then loses its self-locking. The measured shift times are published as an open dataset.

Comment
Original German title (2019): Entwickeln eines automatisierten Schaltgetriebes fuer Motorraeder. Diploma thesis, Westsaechsische Hochschule Zwickau, 2019; revised English edition 2026. 73 pages, 30 figures, 15 tables. Firmware and shift time dataset: https://doi.org/10.5281/zenodo.23002655)

Closest papers

Nearest neighbours by meaning across the whole index.

Electric Racing Kart with BLDC Drive, LiFePO4 Battery System, Traction Control and Regenerative Braking

eess.SY ·2026-10-06 ·Johannes Stockhammer, Tom Rettenwander, Philipp Huber
publishedunusual similarity 0.50
Abstract · German title: Elektro-Rennkart mit BLDC-Antrieb, LiFePO4-Batteriesystem, Antischlupfregelung und Rekuperation. Diploma thesis, HTL Braunau, …

This diploma thesis documents the conversion of a petrol-powered go-kart into a battery-electric kart with a 10 kW BLDC drive, a LiFePO$_4$ traction battery with battery management system, a slip-based traction control and regenerative braking. The traction control estimates the slip of the driven rear axle from three Hall-effect wheel-speed sensors as $λ= (v_R - v_F)/v_R$ and reduces the torque command of the throttle pedal when the axle slips. It runs on a 32-bit ARM Cortex-M3 microcontroller (SAM3X8E) in the signal path between pedal and motor controller, with galvanic isolation and an emergency stop. Regenerative braking uses the generator mode of the motor controller in three stages: motor brake on throttle release, light braking via a steering-wheel button, and blended braking with the hydraulic brake. Drivetrain calculations show that the kart is traction-limited. At rated torque, the drive force at standstill exceeds the transmissible traction force by a factor of 1.7 to 2.0, up to approx. 27 to 43 km/h. Traction control is therefore a functional requirement of the drivetrain. The calculated top speed is approx. 65 km/h. Regenerative braking reaches approx. 0.45 g and could cover up to about 30 % of the energy demand on a winding track. With 80 % of the nominal battery energy, approx. 44 min of driving at 50 % motor load result, so the target of one hour is missed. The initial charging measurement quantifies the flat LiFePO$_4$ voltage plateau at 0.7 to 1.8 mV per percent state of charge, which makes voltage-based state-of-charge estimation unreliable. Cold cells showed a voltage sag under load that triggered the low-voltage alarm. Validation of the control functions by instrumented driving tests is the main open point.

0.38

BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes

cs.RO ·2026-11-18 ·Deepak Kapa, Aman Singh, Saketh Vegesna, Suryank Joshi, Mayank Goswami +1 more
top venuecode/data similarity 0.49
Abstract · 8 pages, 6 figures, 2 tables. Project page: https://deepak-kapa.github.io/PancakeActuator/ Accepted to IEEE Robotics and Automation Letters …

Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.

0.68

A Second Torque Port for Series Elastic Actuators: Parallel-Integrated Design and Time-Scale Torque Allocation

cs.RO eess.SY ·2026-09-25 ·Donghao Jia, Xiubo Xia, Junhang Liu, Zeyu Zhu, Xiaoyu Geng +1 more
unusual similarity 0.46
Abstract · 8 pages, 9 figures, 1 table. Submitted to IEEE Robotics and Automation Letters

A series elastic actuator has a single torque port and pays for it twice: the geared motor must swing its own reflected inertia through the spring, so the amplitude it delivers collapses as $ω^{-2}$ in the command frequency $ω$ once it saturates, while commands below the transmission's breakaway friction never arrive at all. This letter opens a second torque port on the load side, placing a frameless direct-drive micro motor in parallel with a fixed-stiffness spring -- a parallel-integrated SEA, or Pi-SEA, whose delivered torque is read from spring deflection and micro current without a sensor -- and dividing the commanded torque between the two channels by time scale rather than by filter design. The micro torque loop is the fast subsystem, which makes the closed loop singularly perturbed and turns the separation the channels need into a bound to check rather than a crossover to tune; a leaky mid-ranging integrator returns the steady load to the spring; and the amplitude ceiling, read backwards, becomes a closed-form sizing rule that matches spring, geared motor and micro motor to the amplitudes and frequencies an application asks for. Against SEAs, the Pi-SEA widens the tracked band at small amplitudes and lowers the residual the joint imposes on its environment, each by an order of magnitude.

0.29

Modeling Load-, Velocity-, and Temperature-Dependent Transmission Errors of Cycloidal Drives for Industrial Robots Using Fourier Series

cs.RO eess.SPeess.SY ·2026-09-24 ·Christian J. E. Bauer, Valentin Kamm, Marcel Dzubba, Lukas Steinle, Armin Lechler +1 more
publishedunusualhighly cited similarity 0.45
Abstract · 7 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-4454

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

0.85

Design and Control of a Cable-Driven Switchable Actuator with Torque/Tension Dual Modes for Exoskeletons

cs.RO eess.SY ·2026-09-20 ·YuanLong Ji, Xu Liu, Xinyuan Cai, Qihan Ye, Xiangyu Xie +6 more
top venue similarity 0.45
Abstract

Existing wearable exoskeleton architectures are typically constrained by a single mechanical output modality, providing either joint torque around an anatomical joint or linear traction along a limb-training-oriented direction, which limits adaptability to diverse training scenarios. This letter presents a cable-driven switchable actuator (CDSA) that can rapidly switch between torque and tension modes while centralizing all sensing and actuation components at the proximal drive unit. A Coupled Movable Pulley Mechanism (CMPM) provides tension amplification at the distal end-effector, while a bidirectional Cable-Driven Ratchet Mechanism (CDRM) enables mode switching and preload regulation. To eliminate the need for distal instrumentation, multi-source proximal sensors are integrated with a data-driven fusion model to estimate distal output forces. An adaptive dual-mode force control strategy based on iterative learning control (ILC) is further developed. Platform experiments demonstrate transmission efficiencies of $(92.4 \pm 2.0)\%$ and $(96.5 \pm 3.3)\%$ in the torque and tension modes, respectively, along with a tension amplification ratio of $2.77 \pm 0.10$ under tension mode. Tracking tests on simulated knee-joint gait trajectories and short-stroke tension profiles yield stable control, with RMSEs of $(4.52 \pm 0.51)\%$ and $(3.15 \pm 0.19)\%$ of the uncontrolled peak value, respectively. Finally, seated human-coupled experiments validate the system's controllable force generation in both joint-torque and linear-traction application modes.

0.40

Lubricant Temperature Observer for Gearboxes in Industrial Robots

eess.SY cs.ROeess.SP ·2026-09-24 ·Christian J. E. Bauer, Markus Neher, Valentin Kamm, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.44
Abstract · 8 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-5015

The position and path accuracy of industrial robots is strongly affected by temperature. In particular, temperature-dependent friction and altered hysteresis and transmission errors in the gearboxes are the main causes of these deviations. Since standard industrial robots lack temperature sensors, it is proposed to estimate the gearbox lubricant temperature using observer structures. It is planned to apply the proposed lubricant temperature observer to provide the input for temperature-dependent error compensation for gearboxes in industrial robots. First, a two-state heat transfer model describing the heat transfer from the lubricant through the gearbox housing to the environment is described and identified. It is integrated into a Luenberger observer and a Kalman filter with a correction of the lubricant temperature estimation based on measurements from a housing temperature sensor. Temperature measurements were performed in an experimental setup with a cycloidal gear filled with grease, which is common for industrial robots. Due to its changing viscosity and changing thermal conductivity at different shear rates, it shows a less uniform thermal behavior than gear-oil. For the validation measurements, the developed observers showed a mean absolute error of 1.3 K.

0.80

Real-Time Transient Response Optimization

eess.SY ·2026-08-22 ·Anahida Kanade, Djan Tanova, Steve Conner, Taner Dosluoglu
published similarity 0.43
Abstract · 6 pages, 9 figures, 1 table. Technical correspondence of original research and data that has not yet been accepted for publication in any jo…

Use of artificial intelligence in motor control applications that can be deployed within the microcontrollers need to comply with real-time demands of motor control systems. A supplementary controller approach that can be integrated within existing microcontrollers is presented. The proposed approach is implemented on a weeteq motor control integrated circuit and tested in the lab. A complete unsupervised motor control deployment solution was developed, and the real-time system response correction demonstrated under dynamic loads measured with and without the supplementary controller. The solution provides 100% coverage of real-time data at control loop sample rate and model inference period between 100usec and 1msec. The importance of latency for reduction of dynamic regulation margin during transient response is demonstrated with up to 68% reduction of the system response error. A novel key performance indicator based on principal components transform is introduced that provides a quantitative figure of merit for improvement of the transient response, in terms of the dynamic regulation margin, stability considerations and iterative improvements of consecutive regression model outputs. The significant events related to dynamic changes in the equipment and external operating conditions are detected at milliseconds resolution and recorded as highly compressed vectors representing deviation of the system response from linear steady state conditions. The resolution in time and accuracy of this vector data will enable a new level of system level optimisation that has not been possible using the time series data from IoT sensors in current equipment health monitoring solutions.

0.36

Actuator-Aware Observer Inputs for Cascade ADRC of Quadrotors Under Rotor Lag, Measurement Delay and Sensor Noise

cs.RO ·2026-10-29 ·Xuan-Quy Dao, Ngoc-Bich Le, Le-Minh Nguyen
code/data similarity 0.43
Abstract · 19 pages. MATLAB and PX4 SITL evaluation. Code, controller gains, random seeds, and per-seed results: https://github.com/Quang61123/actuator…

In sampled cascade linear active disturbance rejection control (LADRC) of quadrotors, the extended-state observer receives the instantaneous command, although the delayed measurement reflects an earlier, rotor-filtered acceleration. This simulation and software-in-the-loop design study examines actuator-aware (AA) observer inputs: altitude and attitude observers use limited virtual inputs filtered by an assumed rotor model and aligned with the measurement delay, and horizontal observers use acceleration reconstructed from measured attitude. Fixed gains are selected on the discrete-time model under sensitivity and step-response requirements and stationary covariance ceilings on channel activity and on the noise-induced inner-loop increment of the full cascade. In paired set-point trials, PID-Budget, AA-Budget and AA-HalfGain reach mean RMSEs of 65.5, 19.2 and 16.9~mm; under a stricter common cascade ceiling, the AA designs reach 29.9 and 26.4~mm versus 72.3~mm for a PID with about twice their rotor-command increment. Ablations attribute the improvement to the rotor-lag model and the measured-attitude input; at the nominal 5-ms delay, delay alignment changes the RMSE by 0.013~mm. PX4 software-in-the-loop runs reproduce these results. Behind EKF2, a noise model fitted to the estimation errors predicts the roll/pitch and yaw increments within 5\%. After redesign for this stack, AA-Budget-E reduces the set-point RMSE from 59.1~mm (PID-E) to 44.0~mm with a lower rotor-command increment in every paired tracking run (S6: 45\% lower, 15\% after output quantization); AA-HalfGain-E beats PID-E only on the lemniscate. With fixed gains, the AA designs tolerate less unmodelled rotor lag and delay than PID in the linear sensitivity screen. The ceilings are nominal tuning constraints.

0.52