CS Paper Radar

A Second Torque Port for Series Elastic Actuators: Parallel-Integrated Design and Time-Scale Torque Allocation

Donghao Jia, Xiubo Xia, Junhang Liu, Zeyu Zhu, Xiaoyu Geng, Jian Sun

cs.RO eess.SY ·submitted 2026-09-25 06:30 UTC · v1
unusual

Abstract

A series elastic actuator has a single torque port and pays for it twice: the geared motor must swing its own reflected inertia through the spring, so the amplitude it delivers collapses as $ω^{-2}$ in the command frequency $ω$ once it saturates, while commands below the transmission's breakaway friction never arrive at all. This letter opens a second torque port on the load side, placing a frameless direct-drive micro motor in parallel with a fixed-stiffness spring -- a parallel-integrated SEA, or Pi-SEA, whose delivered torque is read from spring deflection and micro current without a sensor -- and dividing the commanded torque between the two channels by time scale rather than by filter design. The micro torque loop is the fast subsystem, which makes the closed loop singularly perturbed and turns the separation the channels need into a bound to check rather than a crossover to tune; a leaky mid-ranging integrator returns the steady load to the spring; and the amplitude ceiling, read backwards, becomes a closed-form sizing rule that matches spring, geared motor and micro motor to the amplitudes and frequencies an application asks for. Against SEAs, the Pi-SEA widens the tracked band at small amplitudes and lowers the residual the joint imposes on its environment, each by an order of magnitude.

Comment
8 pages, 9 figures, 1 table. Submitted to IEEE Robotics and Automation Letters

Closest papers

Nearest neighbours by meaning across the whole index.

BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes

cs.RO ·2026-11-18 ·Deepak Kapa, Aman Singh, Saketh Vegesna, Suryank Joshi, Mayank Goswami +1 more
top venuecode/data similarity 0.50
Abstract · 8 pages, 6 figures, 2 tables. Project page: https://deepak-kapa.github.io/PancakeActuator/ Accepted to IEEE Robotics and Automation Letters …

Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.

0.68

Design and Control of a Cable-Driven Switchable Actuator with Torque/Tension Dual Modes for Exoskeletons

cs.RO eess.SY ·2026-09-20 ·YuanLong Ji, Xu Liu, Xinyuan Cai, Qihan Ye, Xiangyu Xie +6 more
top venue similarity 0.46
Abstract

Existing wearable exoskeleton architectures are typically constrained by a single mechanical output modality, providing either joint torque around an anatomical joint or linear traction along a limb-training-oriented direction, which limits adaptability to diverse training scenarios. This letter presents a cable-driven switchable actuator (CDSA) that can rapidly switch between torque and tension modes while centralizing all sensing and actuation components at the proximal drive unit. A Coupled Movable Pulley Mechanism (CMPM) provides tension amplification at the distal end-effector, while a bidirectional Cable-Driven Ratchet Mechanism (CDRM) enables mode switching and preload regulation. To eliminate the need for distal instrumentation, multi-source proximal sensors are integrated with a data-driven fusion model to estimate distal output forces. An adaptive dual-mode force control strategy based on iterative learning control (ILC) is further developed. Platform experiments demonstrate transmission efficiencies of $(92.4 \pm 2.0)\%$ and $(96.5 \pm 3.3)\%$ in the torque and tension modes, respectively, along with a tension amplification ratio of $2.77 \pm 0.10$ under tension mode. Tracking tests on simulated knee-joint gait trajectories and short-stroke tension profiles yield stable control, with RMSEs of $(4.52 \pm 0.51)\%$ and $(3.15 \pm 0.19)\%$ of the uncontrolled peak value, respectively. Finally, seated human-coupled experiments validate the system's controllable force generation in both joint-torque and linear-traction application modes.

0.40

Direct Electromechanical Actuation of the Shift Drum in Non-Synchronized Motorcycle Transmissions: From Actuator Sizing and Electronics Design to Closed-Loop Position Control

eess.SY ·2026-10-12 ·Johannes Stockhammer
unusual similarity 0.46
Abstract · Original German title (2019): Entwickeln eines automatisierten Schaltgetriebes fuer Motorraeder. Diploma thesis, Westsaechsische Hochschule …

This thesis presents the direct electromechanical actuation of the shift drum in a non-synchronized motorcycle transmission. A DC motor drives the shift drum through a self-locking worm gear, so the entire foot shift mechanism is eliminated. As a reference, 84 manual gear changes of a large-displacement series-production motorcycle were measured on a chassis dynamometer; the mean shift time is 80 ms for upshifts and 92 ms for downshifts. The system design covers the complete chain from the mechanics to the software. The actuator motor is sized from inertia, friction and gear ratio. A dedicated shift controller is developed with supply filtering, signal conditioning for the position sensor and the incremental encoder, an H-bridge motor driver and a custom circuit board based on a SAMD21 microcontroller. The embedded firmware implements position control of the shift drum with a proportional controller, without inner speed or current loops. On a gearbox test rig, a gear change is completed in less than 80 ms without overshoot in a single measurement, below the mean of the manual reference shifts. The analysis reveals a trade-off in the choice of the worm gear ratio: at a ratio of 30, about 93% of the motor torque is needed to accelerate the motor shaft and the worm. A ratio of about 8 halves the required torque, but the worm gear then loses its self-locking. The measured shift times are published as an open dataset.

0.34

Ultra-Low-Impedance Robotic Gripper for High-Bandwidth and Transparent Physical Interaction

cs.RO ·2026-08-10 ·Joon Lee, Ari Choi, Seokhwan Jeong
published similarity 0.44
Abstract · ICRA 2026 (Late Breaking Result Poster)

Conventional robotic grippers often use high-ratio transmissions to generate grasping torque and external force sensors to measure physical interaction. High-ratio transmissions increase friction, reflected inertia, and mechanical impedance, while external sensors add hardware complexity. To address these trade-offs, this study proposes a novel 9-DOF, three-fingered Differential Direct-Drive (DDD) gripper that combines DD motors with a low-ratio (1:2) differential transmission. The mechanism centralizes actuator mass at the base to minimize moving-link inertia, while the differential architecture couples two motors in parallel to amplify torque during flexion. Experiments show that the prototype delivers a nominal grasping force of approximately 18 N and a fingertip force of 4.7 N, while maintaining a low motor contribution to system inertia (0.236%) and low passive mechanical impedance, with a maximum measured value of 50.1 N/m when the motors are unpowered. The proposed hardware addresses the trade-offs among torque, physical transparency, and kinematic dexterity, providing a foundation for high-bandwidth interaction and sensorless proprioceptive force estimation.

0.19

Three Machines Suffice for Local Hardening of Electromechanical Oscillations

eess.SY math.DS ·2026-10-17 ·Kai Sun
unusual similarity 0.44
Abstract

The single-degree-of-freedom swing equation with sinusoidal coupling is locally softening: its oscillation frequency decreases with oscillation level near a stable equilibrium. Nonlinear modal interaction, however, can reverse this trend in multimachine systems. This letter gives a necessary-and-sufficient condition for strict leading-order local hardening, measured with respect to canonical action, in two symmetric three-machine operating-point families with equal or opposite power injections at the equal-inertia machines. An exact two-coordinate reduction expresses the condition in terms of a squared modal-frequency ratio and a dimensionless nonlinear coupling measure. The proof retains the induced mean shift and second harmonic and shows that the companion modal family remains locally softening. The criterion recovers both an equal-inertia hardening example and an exact large-inertia threshold. Coherent aggregation recovers the two-machine softening law, whereas the infinite-bus limit retains two dynamic rotor angles and permits hardening. An exact coherent-group extension preserves the selected periodic family, frequency, and canonical action for every finite machine count greater than two. Thus, three finite-inertia machines are the minimum permitting local hardening in the stated undamped, lossless classical model.

0.24

Natural Swing-Up of an Underpowered Double Pendulum

cs.RO eess.SY ·2026-11-12 ·Arne Sachtler, Manuel Keppler, Florian Loeffl, Alin Albu-Schäffer
similarity 0.43
Abstract

Robots with weak motors must ride their natural dynamics rather than fight them. We swing up a direct-drive planar two-link robot, whose motors deliver only about 6\,\% of its shoulder gravity torque, along its nonlinear normal modes, two-dimensional invariant manifolds consisting of periodic orbits. On a non-strict mode, injecting energy necessarily moves the state off the manifold, so pumping and stabilization compete for the same bounded torque. We split the input torque into a power-neutral steering component and a scalar pumping input, the only component that changes the energy. The allocation then becomes a linear program in two variables: maximize pumping subject to the torque limits and one control-Lyapunov constraint. The constraint uses the model-based rate of the error, so no stabilizing feedback gain is needed. Experiments in hardware show swing-ups along both modes and compare the allocation with summing-and-clipping and with prioritized stabilization.

0.30

TinyARM-X: A Series of Open-Source, Configurable, and Transparent Torque-Controlled Desktop-Scale Robotic Manipulators

cs.RO ·2026-11-18 ·Nicolas Kosanovic, Jean Chagas Vaz
similarity 0.43
Abstract · 9 pages, 5 figures. Submitted to a robotics Journal. Reviews have not come in yet

Visuomotor policies have demonstrated that imprecise low-cost robots can autonomously complete complex manipulation tasks. However, most inexpensive manipulators rely on compact and rigidly position-controlled servos for actuation, which complicate simulation, operation, and safety. This work introduces TinyARM-X, a framework for easily manufacturable, configurable, and torque-controllable low-cost (<350 USD) serial manipulators. By using a single hardware/software architecture, a <7 Degree of Freedom (DoF) TinyARM can be manually reconfigured to an operational >3 DoF robot within 10 min. Actuator modeling and dynamic compensation enable torque-controlled applications like mixed-reality impedance control teleoperation and simulator force feedback rendering. Experiments include mechanical benchmarking and real-world force-aware telemanipulation. The TinyARM-7 has a payload of 33.5 g, a max speed of 0.77 m/s, and a reach of 210 mm. Moreover, with dynamic compensation, the robot has a backdrive-breakaway force of 1.4 N and a backdrive-running force of 0.7 N. Additionally, Cartesian-Impedance Control (CIC) attains a translational stiffness of >15 N/m. Lastly, the TinyARM-X stack is open-sourced to disseminate accessible desktop-scale torque-controlled robotic manipulation to the community.

0.22

MuJoCable: Reduced-Order Surface-Routed Cable Transmission for Tendon-Driven Robots

cs.RO cs.CE ·2026-09-09 ·Yi Zhang, Qi Shao, Yicong Lin, Muyuan Ma, Tao Sun +1 more
similarity 0.43
Abstract · 14 pages, 6 figures, 3 tables

Tendon transmissions reduce distal inertia and add compliance, yet routing, slack, and friction govern motion and force transfer. Mainstream rigid-body robotics simulators such as MuJoCo do not jointly resolve moving noncircular contact, unilateral tension, and segment friction. We present MuJoCable, which adds a reduced-order, configuration-dependent cable transmission to MuJoCo. Its routing algorithm jointly optimizes an ordered path across moving analytic and mesh surfaces. A unilateral axial law, directional Capstan propagation, and nodal virtual work map this path to segment tensions and body forces. The warm-started engine plugin applies these forces during simulation and exposes route and load states for design. Pulley benchmarks recover analytical transmission relations with a Capstan-ratio error below 0.5%. On the underactuated 18-joint SpiRobs, MuJoCable reveals friction-driven load growth and proximal redistribution of joint rotation that the native tendon does not represent. Hardware tests on SpiRobs and a tendon-route-coupled finger reproduce observed motion sequences. By making physical threading executable, MuJoCable brings transmission sources of the simulation-to-reality gap into route, cable, and actuator design before fabrication.

0.26