CS Paper Radar

Three Machines Suffice for Local Hardening of Electromechanical Oscillations

Kai Sun

eess.SY math.DS ·submitted 2026-10-17 16:03 UTC · v1
unusual

Abstract

The single-degree-of-freedom swing equation with sinusoidal coupling is locally softening: its oscillation frequency decreases with oscillation level near a stable equilibrium. Nonlinear modal interaction, however, can reverse this trend in multimachine systems. This letter gives a necessary-and-sufficient condition for strict leading-order local hardening, measured with respect to canonical action, in two symmetric three-machine operating-point families with equal or opposite power injections at the equal-inertia machines. An exact two-coordinate reduction expresses the condition in terms of a squared modal-frequency ratio and a dimensionless nonlinear coupling measure. The proof retains the induced mean shift and second harmonic and shows that the companion modal family remains locally softening. The criterion recovers both an equal-inertia hardening example and an exact large-inertia threshold. Coherent aggregation recovers the two-machine softening law, whereas the infinite-bus limit retains two dynamic rotor angles and permits hardening. An exact coherent-group extension preserves the selected periodic family, frequency, and canonical action for every finite machine count greater than two. Thus, three finite-inertia machines are the minimum permitting local hardening in the stated undamped, lossless classical model.

Closest papers

Nearest neighbours by meaning across the whole index.

Isostable-Based Nonlinear Model Reduction for Power System Oscillations

eess.SY math.DS ·2026-09-27 ·Kaiyang Huang, Dan Wilson, Kai Sun
similarity 0.46
Abstract

Power systems are often represented by high-dimensional dynamic models, making nonlinear control design computationally expensive and limiting its practical application. Oscillation analysis and damping control therefore commonly rely on linearized models, which do not capture the nonlinear oscillatory behavior induced by large disturbances. This paper proposes an isostable-based model reduction method for nonlinear modal analysis of power systems. The method constructs an invariant manifold associated with a selected oscillatory mode and uses isostable coordinates to describe the mode with only two real state variables. The isostable formulation gives linear autonomous modal dynamics, with nonlinear state reconstruction and input response computed on the modal manifold. An optimal damping control problem is then formulated directly in the reduced coordinates. Case studies on the IEEE 39-bus system demonstrate the accuracy of the proposed model in describing nonlinear oscillations and show improved damping compared with control designed using a linear reduced model.

0.38

Joint nonlinearity in a stiffened aluminium wingbox panel and what it requires of a reduced basis

cs.CE eess.SYmath-phmath.NA ·2026-09-09 ·Nikolaos D. Tantaroudas, Evangelos Papatheou
similarity 0.46
Abstract · 20 pages, 14 figures

A shell finite-element model of a stiffened aluminium wingbox panel, a laboratory structure shared by several experimental studies, is built with its plate-to-stiffener joints at the $78$ physical fastener positions and calibrated against measured modal data, a six-parameter sensitivity update of the substructure moduli within $\pm20\%$ reproducing the first five measured modes to $1.1$--$4.3\%$ with modal-assurance values of $0.88$--$1.00$. Making the fasteners nonlinear, at equal mesh, mass and damping, shows that joint nonlinearity enters the response strongly asymmetrically. Hardening is almost invisible, at most $+1\%$ in frequency, whereas softening or slipping the joints moves the first three resonances by $-2.1$, $-4.9$ and $-9.2\%$, and friction removes up to $80\%$ of the resonant peak before it recovers. Newmark integration of all $18{,}804$ degrees of freedom and a harmonic balance condensed exactly onto the joints and continued in arclength agree to $5.5\times10^{-4}$. A projection-based nonlinear model order reduction then locates the criterion that a jointed structure imposes on a reduced basis. The binding quantity is not the linear response, which eleven vectors reproduce to better than $0.01\%$, but the receptance of the structure between the joints, of which $126$ global eigenvectors carry about $2\%$, and without which the reduced model overpredicts the hardening shift of the fundamental by a factor of thirty and returns a value beyond the rigid-joint limit of the panel.

0.32

Feasibility of Pareto-Improving Damping Control of Forced Oscillations: The Active-Power Case

eess.SY ·2026-11-13 ·Haozong Wang, Yuru Wu, Yan Wen, Qian Liu, Jiahui Yang +3 more
benchmark similarity 0.45
Abstract

Damping control of a forced oscillation may reduce amplitudes at certain locations while increasing them elsewhere. This paper introduces Pareto improvement as a criterion for assessing such control: at least one nodal oscillation amplitude decreases, while none increases across all other nodes. The analysis considers active-power forcing sources and active-power control injections in connected swing networks with positive inertia and damping. Necessary conditions for Pareto improvement feasibility are derived from the normalized nodal responses. It is proven that for every network with a single oscillation source and a single actuator, at least one positive forcing frequency is shown to preclude Pareto improvement, regardless of the amplitude and phase of the control input. A three-node counterexample shows that this limitation does not persist with multiple actuators. PSS/E simulations of a 6-bus benchmark system and a modified IEEE 39-bus system validated the analysis. These findings suggest the value of assessing control effects across the network and further investigating multi-actuator damping control.

0.30

A Second Torque Port for Series Elastic Actuators: Parallel-Integrated Design and Time-Scale Torque Allocation

cs.RO eess.SY ·2026-09-25 ·Donghao Jia, Xiubo Xia, Junhang Liu, Zeyu Zhu, Xiaoyu Geng +1 more
unusual similarity 0.44
Abstract · 8 pages, 9 figures, 1 table. Submitted to IEEE Robotics and Automation Letters

A series elastic actuator has a single torque port and pays for it twice: the geared motor must swing its own reflected inertia through the spring, so the amplitude it delivers collapses as $ω^{-2}$ in the command frequency $ω$ once it saturates, while commands below the transmission's breakaway friction never arrive at all. This letter opens a second torque port on the load side, placing a frameless direct-drive micro motor in parallel with a fixed-stiffness spring -- a parallel-integrated SEA, or Pi-SEA, whose delivered torque is read from spring deflection and micro current without a sensor -- and dividing the commanded torque between the two channels by time scale rather than by filter design. The micro torque loop is the fast subsystem, which makes the closed loop singularly perturbed and turns the separation the channels need into a bound to check rather than a crossover to tune; a leaky mid-ranging integrator returns the steady load to the spring; and the amplitude ceiling, read backwards, becomes a closed-form sizing rule that matches spring, geared motor and micro motor to the amplitudes and frequencies an application asks for. Against SEAs, the Pi-SEA widens the tracked band at small amplitudes and lowers the residual the joint imposes on its environment, each by an order of magnitude.

0.29

Beyond Phase Reduction: Amplitude Collapse in Optimal Control of Coupled Oscillators

eess.SY math.OCmath.NA ·2026-09-15 ·Faranak Rajabi, Frédéric Gibou, Jeff Moehlis
published similarity 0.44
Abstract · 8 pages, 5 figures. Accepted to the 65th IEEE Conference on Decision and Control (CDC 2026), Honolulu, HI, December 2026

We solve the four-dimensional Hamilton-Jacobi-Bellman (HJB) equation for two diffusively coupled Stuart-Landau-like oscillators to obtain full-state optimal feedback control. A sweep over coupling strength reveals a sharp change in the numerically optimal strategy: below a threshold coupling value, the controller steers the phase difference toward anti-phase while keeping both oscillators near the limit cycle, as reduced-order models would suggest. Above this threshold, the HJB solution changes qualitatively; the controller transiently collapses one oscillator's amplitude to near zero, thereby enabling large phase repositioning near the origin before rebuilding its amplitude. Direct gradient-based and stochastic optimization do not recover this lower-cost collapse trajectory from the initializations considered, suggesting that it occupies a region of the control landscape that is difficult to access by direct search. A joint sweep over nonisochronicity and coupling shows that collapse can occur even for an isochronous oscillator: phase repositioning near the origin can favor an off-cycle strategy. Nonisochronicity provides an additional energetic benefit through a phase-velocity surplus at small amplitude, quantitatively accounting for the observed reduction in control cost. Comparisons with uncoupled and coupled phase-reduced baselines show that phase models become increasingly inaccurate and cost significantly more energy for strong coupling. Results for coupled Van der Pol oscillators further demonstrate that exploitation of off-cycle dynamics is not specific to the Stuart-Landau-like oscillators.

0.36

Symmetry and the Form of Nonlinear Behavioral Models: A Tutorial for Microwave Engineers

eess.SP ·2026-10-01 ·Nicholas B. Tufillaro
similarity 0.44
Abstract · 25 pages, 7 figures, 4 tables. v3: one sentence in the Scope section corrected (multi-harmonic and multi-port cases use the single circle; o…

Behavioral models of nonlinear microwave devices -- the Cardiff model, X-parameters, the higher-order describing functions of the mechanical-systems literature -- all share a functional form. This tutorial derives that form from time invariance alone. It develops the consequences of that derivation using only the harmonic-balance description of a single-tone periodic steady state, in which each port waveform is a finite set of harmonic phasors, and uses them to give the Cardiff model's three exponents physical interpretations. In the monomial rewriting the magnitude exponent $m$ is the order of the device's load-side nonlinearity; the phase exponent $n$ is set by the drive-side harmonic; and the conjugate index $r$ obeys $r_{\max}=\lfloor K/2\rfloor$, where $K$ is the degree of the load-side nonlinearity. The familiar restriction $r\le1$ is therefore a statement about the device, exact whenever $K\le3$. The final sections show that a tailored A-pull measurement displays this decomposition directly: each spectral cluster's half-width is the order of the nonlinearity that produced it. The tutorial is pedagogical and is meant as a gentler introduction to the results treated in the companion paper "Time invariance, circle symmetry, and the completeness of the Cardiff behavioral model", which states and proves the theorems in full.

0.35

Reduced-Order Model Characterization of Nonlinear Sustained Oscillations

eess.SY math.DS ·2026-09-27 ·Kaiyang Huang, Dan Wilson, Kai Sun
similarity 0.43
Abstract

Nonlinear sustained oscillations involving inverter-based resources can happen when device and network interactions produce an attracting limit cycle around an unstable equilibrium. A damping controller must then describe nonlinear dynamics over the region between the two invariant sets, where a local equilibrium linearization can be insufficient. In this paper, a controlled phase--isostable model is first developed on a two-dimensional invariant manifold connecting the equilibrium and the limit cycle. Dynamics on this surface are represented by phase and isostable coordinates, while physical states and control inputs are related to these coordinates through nonlinear reconstruction and response functions. The required functions are computed from connecting trajectories and periodic-orbit data. A control strategy is then designed to provide extra damping while limiting phase distortion. Case studies on a two-area system and an IEEE 39-bus system demonstrate more effective oscillation damping than the compared equilibrium-linearized designs under the same conditions.

0.27

DC-TORQ: Fast Assessment of Data Center-Induced Generator Torsional Oscillation Risk Quantification

eess.SY ·2026-10-15 ·Yingyi Tang, Bin Wang, Junbo Zhao, Qiang Zhang, Pradip Vijayan +2 more
benchmark similarity 0.43
Abstract

The periodic power demand of large data centers can introduce forced oscillations into the power system. When these oscillations contain frequency components near a turbine-generator torsional mode, they may excite sustained shaft torque oscillations with amplitudes exceeding the allowable cyclic torque limits. Characterizing the impact of data center power oscillations on generator shaft torque requires accounting for frequency-dependent network coupling among the data center, the transmission network, and the generators. Although electromagnetic transient (EMT) simulations can capture these interactions in detail, repeated simulations across excitation frequencies and load locations can be computationally demanding. This paper proposes an analytical framework for data center induced torsional oscillations that retains the coupled electrical and shaft dynamics. A detailed generator-network model is established, and closed-form transfer functions that map data center power perturbations to the torque in each shaft section are derived. Admissible shaft torque amplitudes are then translated into frequency-dependent limits on data center power oscillations. The proposed framework enables fast assessment of the shaft torque response while accounting for network dynamics and provides a quantitative screening criterion for candidate data center connection buses. The framework is validated on the IEEE benchmark model and applied to the IEEE 39-bus system.

0.19