CS Paper Radar

BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes

Deepak Kapa, Aman Singh, Saketh Vegesna, Suryank Joshi, Mayank Goswami, Shishir Kolathaya

cs.RO ·submitted 2026-11-18 09:50 UTC · v1
top venuecode/data

Abstract

Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.

Comment
8 pages, 6 figures, 2 tables. Project page: https://deepak-kapa.github.io/PancakeActuator/ Accepted to IEEE Robotics and Automation Letters (RA-L)

Closest papers

Nearest neighbours by meaning across the whole index.

QLAUN: A Research-Oriented, Robust, Agile, Modular, and Affordable Torque-Controlled Quadruped Robot

cs.RO ·2026-09-03 ·Mohamad S. Moudallal, Noel J. Maalouf
published similarity 0.59
Abstract · Extended abstract presented at IEEE ICRA@40, Rotterdam, Netherlands, September 2024. 2 pages, 1 figure

QLAUN Bot (Quad-Legged Adaptive Unmanned Navigator Robot) is a torque-controlled quadruped robot that is research-oriented, cost-effective, and aimed at achieving simultaneous robustness and agility while being completely 3D-printed. It is a quadruped robot that is aimed at empowering robotics research at universities and research institutes in Lebanon and the MENA region. Using a novel electronics-free leg design strategy, we present a modular robot with interchangeable and easily replaceable legs. The 15 kg robot possesses 12 DoF (Degrees-of-Freedom) with three per leg, each paired with a completely 3D-printed Quasi-Direct Drive (QDD) actuator that consists of a brushless DC motor and a low-ratio gearbox transmission that is connected to a belt transmission system for significantly increasing the torque outputs at the joints. We present legs that have decoupled hip and knee actuators to improve the overall modularity of the robot. QLAUN is almost completely 3D-printed using polylactic acid (PLA) and assembled using off-the-shelf parts to create a robust, agile, and affordable robot for legged robot locomotion research. The legs possess joints with wide ranges of motion, including a continuous hip flexion-extension joint. A compliant foot, printed using TPU-95A is also implemented for alleviating hard impacts and handling terrain uncertainties. This extended abstract aims to introduce QLAUN, a novel platform for robotics research, emphasizing the design concepts and principles that underpin its development to the academic and research communities in the field of robotics.

0.34

Modeling Load-, Velocity-, and Temperature-Dependent Transmission Errors of Cycloidal Drives for Industrial Robots Using Fourier Series

cs.RO eess.SPeess.SY ·2026-09-24 ·Christian J. E. Bauer, Valentin Kamm, Marcel Dzubba, Lukas Steinle, Armin Lechler +1 more
publishedunusualhighly cited similarity 0.58
Abstract · 7 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-4454

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

0.85

Task-Oriented Co-Design and Optimization of Geared Actuators for Robotic Applications

cs.RO ·2026-09-19 ·Xuanyu Huang, Jianqiang Dong, Hang Zhao
hot direction similarity 0.58
Abstract

Different tasks performed by legged robots impose distinct torque and speed requirements on actuators. Existing robotic actuators are generally optimized at the component level for metrics such as torque or power density, without explicit task guidance. System-level optimization across components such as motors, gearboxes, and sensors is challenging because of the high computational cost and coupling among mechanical, electrical, and electromagnetic behaviors. Consequently, improvements in individual components may not translate into better robot performance in a specific task. To this end, we present a systematic optimization framework for task-oriented co-design of actuator hardware and control. First, surrogate models are employed to accelerate motor evaluation and support global exploration of the coupled design space. Then, a hierarchical mixed-variable optimization strategy is adopted, combining discrete enumeration with continuous search over dimensions and real-valued indices. These indices are rounded to select admissible values for the remaining discrete choices before each evaluation. Within this search, rated output torque density and task performance are jointly optimized, with Bezier-parameterized joint torque profiles determined for each hardware candidate. Finally, the effectiveness of the proposed framework is validated through actuator fabrication and experiments on a two-degree-of-freedom jumping leg. Based on its measured mass, the fabricated prototype achieves a nominal rated output torque density of 35.7 N m/kg, approximately 60% higher than that of a widely used commercial geared joint actuator, while being 18.6% lighter. Under matched bench conditions, it achieves 12.0% greater jump height at twice-rated torque. Together, these results demonstrate a systematic route from task requirements to actuator design and control.

0.36

QDD-MM: A Simple and Compact Open-Source Muscle Module with Quasi-Direct-Drive Motor for Tendon-driven Robots

cs.RO ·2026-11-18 ·Kento Kawaharazuka, Yoshimoto Ribayashi, Takahiro Hattori, Shunnosuke Yoshimura, Kei Okada
publishedcode/data similarity 0.55
Abstract · Accepted to IEEE-RAS Humanoids 2026, website - https://haraduka.github.io/qddmm/, youtube - https://www.youtube.com/watch?v=09xRhZO497k

Tendon-driven robots, which actuate like biological muscles by using motors to wind wires, offer advantages such as variable stiffness and redundant actuation. Despite these advantages, musculoskeletal structures inherently involve a large number of diverse muscles, making it desirable to compactly modularize each muscle unit and flexibly accommodate diverse muscle arrangements. While various small muscle modules have been proposed to date, existing designs tend to be complex, difficult to maintain, and suffer from low backdrivability and limited actuation speed due to their high gear ratios. In this work, we propose QDD-MM, a muscle module that leverages recent advances in quasi-direct-drive motors to achieve a simpler and more compact structure with higher backdrivability and faster actuation than previous modules. By utilizing quasi-direct-drive motors, the module eliminates the need for dedicated force-sensing mechanisms, significantly simplifying the overall design, while also supporting flexible wire routing in multiple directions, various module-to-module connections, and even the use of the module body itself as a structural component. QDD-MM integrates these capabilities into a reusable muscle module, and its design is openly available at https://github.com/haraduka/qddmm. We developed tendon-driven robots with one joint and either two or three muscles, as well as a partial musculoskeletal humanoid, using the proposed QDD-MM and verified their effectiveness. We expect that this muscle module will democratize tendon-driven robotics and further accelerate progress in the field.

0.71

Structure-Actuation Co-Design of All-Electric Heavy-Duty Robotic Manipulators

cs.RO eess.SY ·2026-10-27 ·Mohammad Bahari, Amir Hossein Barjini, Jouni Mattila
benchmark similarity 0.54
Abstract · 6 pages manuscript submitted to a conference (ICCMA 2026)

This paper presents a mixed discrete-continuous multiobjective bilevel framework for the structure-actuation co-design of all-electric heavy-duty robotic manipulators. The upper level optimizes manipulator geometry and actuation topology, while joint-specific lower-level searches construct feasible archives of discrete motor, gearbox, and screw configurations. A system-level coordinator selects actuator packages according to hardware mass, co-design cost, and loss-aware supply energy, and the resulting actuator masses are fed back to the robot model until a mass-consistent fixed point is obtained. Evaluation on a full-pose SE(3) benchmark with a 100-kg tool payload yields eight feasible nondominated designs, all satisfying the 12 prescribed poses. Actuator-mass coupling converges in three iterations for every reported design. A fixed-design ablation shows that one-pass sequential sizing changes hardware mass by up to 2.13%, co-design cost by 10.20%, and supply energy by 9.40% in magnitude. Payload screening further reveals increasing mass-cost-energy demand and changes in competitive mechanism topology with carried load.

0.45

Design and Validation of a Lightweight, Low-Profile Powered Knee Prosthesis with Quasi-Direct Drive Actuation

cs.RO ·2026-09-02 ·Ross J. Cortino, Ryan Posh, Emily G. Keller, Robert D. Gregg
similarity 0.54
Abstract · 11 pages, 8 figures, Under Review

Fully-powered knee prostheses, unlike traditional passive knees, can perform controlled positive work, reducing the need for compensatory behaviors by users during energy-intensive activities. While quasi-direct drive (QDD) actuators provide superior torque control, backdrivability, and acoustic noise properties compared to traditional highly-geared actuators, prior QDD prototypes have been too heavy and bulky for commercial translation. In this work, we present the design and validation of a new lightweight (2.6 kg) and low-profile (24.5 cm tip-to-tip build height) QDD knee prosthesis. By optimizing an 18 to 1 two-stage transmission alongside thermal and structural finite-element analyses, we significantly reduce device mass while enabling a peak torque of 145 Nm. Through benchtop tests, we validate the device's high output torque, low backdrive torque (1 Nm), and its precision position and torque control capabilities. We also demonstrate biomimetic kinematics and peak knee extension torques (within one standard deviation of able-bodied references) during both level-ground walking and sit-stand transitions performed by three participants with transfemoral amputation and varying K-levels. By meeting or improving upon the mass, build height, peak torque, and acoustic noise of a leading commercial powered knee, this work establishes the clinical viability of emerging QDD prostheses that promise improved dynamic performance for their users.

0.32

RAIPAL: A Powerful and Agile Humanoid Arm for Human Tasks

cs.RO ·2026-11-03 ·Donggeon Kim, Hyungho Chris Choi, Donghyuk Choi, Jeongsoo Park, Choongin Lee +2 more
top venue similarity 0.54
Abstract · Published in IEEE Robotics and Automation Letters (RA-L), 2026. Supplementary video: https://youtu.be/xVUWFICD5G0

This paper presents humanoid manipulator hardware designed specifically for human-level performance throughout its broad domain of tasks, from heavy payloads to highly dynamic motions. Unlike conventional designs targeting uniform workspace capability, the proposed approach derives force, speed, and endurance targets from published measurements of task-relevant human upper-limb performance. These targets guide the actuator, mechanism, and thermal design toward torque transparency and sustained operation. The platform integrates force-oriented upper-arm components, speed-oriented forearm components, and a posture-dependent elbow mechanism that shifts its torque-speed behavior. These components are driven by planetary actuators and compact actuator-embedded electronics. Experimental results validate broad task capability, demonstrating a peak payload of 20 kg (2.25x its own mass), an endpoint speed of 20.6 m/s, and continued operation under repeated hammering impacts. Thermal analysis further confirms that the robot's sustained operation capability exceeds the published human load--duration boundary across nearly the entire load spectrum. These findings show that hardware targets derived from human-task measurements narrow the human-to-humanoid capability gap. A supplementary video is available at https://youtu.be/xVUWFICD5G0

0.48

Detachable Wire Drive : Reconfigurable Robot Architecture with Shared Actuators

cs.RO ·2026-08-16 ·Takahiro Hattori, Kento Kawaharazuka, Kei Okada
published similarity 0.54
Abstract · Accepted at IROS2026, website - https://hatofly.github.io/detachable-wire-drive/

Reconfigurable robots offer significant potential for adapting to diverse tasks; however, conventional centralized architectures often require dedicated actuators for each module, leading to substantial increases in overall system weight, volume, and cost. To address these challenges, this paper presents the "Detachable Wire Drive," a reconfigurable robotic system that enables the sharing of heavy and expensive actuators across various morphologies. The core of this system is the "Wire Detach Unit," a mechanism designed to physically split and reconnect wire drive paths, allowing motors to be consolidated into a common base unit. We demonstrate the versatility of this approach by developing a 2-DOF rigid arm, a continuum arm, and two distinct grippers, all of which are interchangeably attached to, and driven by, a single shared actuator set. Experimental results validate the mechanical reliability of the detachment process and the control framework's ability to seamlessly manage transitions between configurations, highlighting a path toward more efficient and multi-functional robotic systems.

0.39