CS Paper Radar

RAIPAL: A Powerful and Agile Humanoid Arm for Human Tasks

Donggeon Kim, Hyungho Chris Choi, Donghyuk Choi, Jeongsoo Park, Choongin Lee, Chan Park, Jemin Hwangbo

cs.RO ·submitted 2026-11-03 05:18 UTC · v1
top venue

Abstract

This paper presents humanoid manipulator hardware designed specifically for human-level performance throughout its broad domain of tasks, from heavy payloads to highly dynamic motions. Unlike conventional designs targeting uniform workspace capability, the proposed approach derives force, speed, and endurance targets from published measurements of task-relevant human upper-limb performance. These targets guide the actuator, mechanism, and thermal design toward torque transparency and sustained operation. The platform integrates force-oriented upper-arm components, speed-oriented forearm components, and a posture-dependent elbow mechanism that shifts its torque-speed behavior. These components are driven by planetary actuators and compact actuator-embedded electronics. Experimental results validate broad task capability, demonstrating a peak payload of 20 kg (2.25x its own mass), an endpoint speed of 20.6 m/s, and continued operation under repeated hammering impacts. Thermal analysis further confirms that the robot's sustained operation capability exceeds the published human load--duration boundary across nearly the entire load spectrum. These findings show that hardware targets derived from human-task measurements narrow the human-to-humanoid capability gap. A supplementary video is available at https://youtu.be/xVUWFICD5G0

Comment
Published in IEEE Robotics and Automation Letters (RA-L), 2026. Supplementary video: https://youtu.be/xVUWFICD5G0
Journal ref
IEEE Robotics and Automation Letters 11(12) (2026) 13813-13820
DOI
10.1109/LRA.2026.3741787

Closest papers

Nearest neighbours by meaning across the whole index.

Beyond Human-Derived Motion: Exploring Robot-Specific Execution for Construction Humanoids

cs.RO ·2026-10-16 ·MinJun Chang, Taehyung Kim, Yong K. Cho, Francis Baek
similarity 0.63
Abstract

Construction productivity has remained a per- sistent challenge, motivating growing interest in humanoid robots that can operate in workspaces and with tools designed for human workers. Realizing this potential requires effective motion control, for which human-derived motion transfer has emerged as a promising approach by capturing and retargeting human demonstrations to humanoid robots. While promising, however, human-derived motion transfer may not fully define how a humanoid should ultimately execute the transferred motion. Once task-relevant motion information has been con- veyed, the humanoid may also exploit its own embodiment through motions that depart from the human demonstration. This study examines whether such Robot-Specific Motion offers an advantage in motion execution efficiency over Human- Derived Motion. On an adult-sized Unitree H1-2, Human- Derived Motion was generated through vision-based capture and retargeting, whereas Robot-Specific Motion used inverse kinematics and minimum-jerk transfers to reach the same targets while departing from the demonstrated posture, as verified using Rapid Upper Limb Assessment (RULA). Across a pick-and-stack sequence representing construction material handling, with four matched motion targets and three trials per condition, Robot-Specific Motion achieved 12.87 s versus 25.03 s in execution time, 0.92 m versus 4.33 m in trajectory length, and 58.7 J versus 247.3 J in two-arm mechanical work. These findings suggest that allowing humanoids to depart from demonstrated human motion may offer additional opportunities for more efficient motion execution, while broader construction tasks are needed to determine whether such differences trans- late into productivity gains.

0.09

A fully articulated humanoid dexterous hand with human-level joint structure enabled by linkage-based actuation

cs.RO ·2026-10-27 ·Jihao Li, Jianguo Wang, Haotian Guo, Yanzhe Wang, Guodong Lu +1 more
similarity 0.62
Abstract

Humanoid dexterous hands are a core component of embodied intelligence, enabling robots to translate high-level intent into rich and adaptive physical interaction. However, existing designs remain constrained by a persistent trade-off among anthropomorphic kinematic complexity, mechanical robustness, load capacity and control simplicity, limiting dexterous manipulation in unstructured environments. Here we present Torch-Hand, a fully articulated humanoid dexterous hand that replicates the joint structure and motion hierarchy of the human hand with 21 degrees of freedom (DOF), comprising a highly articulated five-DOF thumb and four DOF in each of the remaining fingers. The differentiated thumb integrates multi-axis CMC motion to provide broad opposition and flexible contact orientation relative to the four fingers. Unlike tendon-driven or hybrid actuation approaches, Torch-Hand adopts an entirely linkage-based transmission architecture. By integrating screw-linkage actuation, the hand achieves high grasping force and substantial payload capacity while maintaining a compact anthropomorphic form. Its actuation architecture is optimized for control tractability, with all actuators integrated within the palm and arranged in a serial-robot-like configuration that establishes a direct correspondence between motor motion and joint kinematics. This architecture mechanically decouples functional DOF to reduce unintended inter-joint motion propagation, while allowing independently addressable DOF to be actively coordinated into coupled multi-joint motion patterns during complex manipulation. Comprehensive experiments assess reachable workspace, coordinated fingertip trajectories, thumb opposition, 33-grasp taxonomy coverage, grasping force, payload capacity and task-level manipulation. These results establish Torch-Hand as a robust hardware foundation for dexterous embodied manipulation.

0.22

A Dual-Cam Parallel Elastic Actuator with Shared Gas-Spring Compensation for Humanoid Ankles

cs.RO ·2026-08-31 ·Jingcheng Jiang, Yifang Zhang, Nikos G. Tsagarakis
published similarity 0.62
Abstract · Accepted to IEEE AIM 2026. Copyright 2026 IEEE. Personal use of this material is permitted

To improve torque capacity and energy efficiency of humanoid ankles, this paper proposes a 2-DoF parallel elastic actuator (PEA). The main novelty of the proposed design lies in its dual-cam, single-gas-spring architecture, which enables torque compensation in both pitch and roll using a shared elastic element, thereby improving structural compactness compared with conventional multi-element compensation schemes. By leveraging parallel gas springs and customized cam modules, the proposed architecture provides dual-axis torque assistance tailored to specific task requirements. The second key contribution is the formulation of a coupled 2-DoF mathematical model that explicitly captures the interdependence between the two compensation units through the shared spring. Based on this model, an optimization-based design framework is developed to synthesize customized cam profiles from prescribed torque references, establishing a systematic link from task requirements to hardware realization. The complete lower-leg CAD integration is presented in detail. Static FEA and kinematic simulations confirm the design's feasibility and torque-relief effectiveness. The results highlight the proposed design as a compact, customizable solution for 2-DoF humanoid ankle torque compensation.

0.48

PACT: Pose-Robust Actuation Co-Design for Tendon-Driven Robotic Hands

cs.RO ·2026-11-03 ·Prashant Kumar, Rachael Granberry, Taylor Niehues, Andrew A. Stanley, Gabe Pirie
similarity 0.62
Abstract

Humanoid robotic hands must provide sufficient force, speed, and backdrivability within a human-scale envelope. Tendon-driven transmissions address this challenge by relocating actuators to the palm and forearm, but routing paths, moment arms, and capstan dimensions jointly determine both force capability and joint speed, so selecting them sequentially satisfies one requirement at the expense of the other. This paper presents a pose-robust actuation co-design for tendon-driven robot hands (PACT) framework that optimizes tendon routing, moment arms, and capstan dimensions under pose-dependent force requirements and drivetrain-bandwidth constraints. A feasible-force formulation enforces actuator bounds and equilibrium at all joints, while a max-min objective maximizes task-force coverage at the weakest pose. Applied to a four-degree-of-freedom finger, the framework produces an asymmetric N + 1 tendon topology using quasi-direct-drive actuators. Across eight poses, the design achieves task-force coverage of 0.88-1.00 and a predicted 5 Hz minimum isolated-joint flexion/extension bandwidth within a 70th-percentile human-size envelope. Prototype measurements deviate from predictions by up to 24.5%, primarily due to unmodeled transmission losses. These results indicate that co-designing routing with the drivetrain can meet pose-dependent force requirements without relaxing the bandwidth constraint, paving the way for human-sized robotic hands with human-level performance.

0.08

Design and Validation of a Lightweight, Low-Profile Powered Knee Prosthesis with Quasi-Direct Drive Actuation

cs.RO ·2026-09-02 ·Ross J. Cortino, Ryan Posh, Emily G. Keller, Robert D. Gregg
similarity 0.61
Abstract · 11 pages, 8 figures, Under Review

Fully-powered knee prostheses, unlike traditional passive knees, can perform controlled positive work, reducing the need for compensatory behaviors by users during energy-intensive activities. While quasi-direct drive (QDD) actuators provide superior torque control, backdrivability, and acoustic noise properties compared to traditional highly-geared actuators, prior QDD prototypes have been too heavy and bulky for commercial translation. In this work, we present the design and validation of a new lightweight (2.6 kg) and low-profile (24.5 cm tip-to-tip build height) QDD knee prosthesis. By optimizing an 18 to 1 two-stage transmission alongside thermal and structural finite-element analyses, we significantly reduce device mass while enabling a peak torque of 145 Nm. Through benchtop tests, we validate the device's high output torque, low backdrive torque (1 Nm), and its precision position and torque control capabilities. We also demonstrate biomimetic kinematics and peak knee extension torques (within one standard deviation of able-bodied references) during both level-ground walking and sit-stand transitions performed by three participants with transfemoral amputation and varying K-levels. By meeting or improving upon the mass, build height, peak torque, and acoustic noise of a leading commercial powered knee, this work establishes the clinical viability of emerging QDD prostheses that promise improved dynamic performance for their users.

0.32

Composable Dynamics for Cooperative Humanoids: A RoboCompiler Extension

cs.RO ·2026-10-09 ·Mehdi Heydari Shahna, Jouni Mattila
similarity 0.61
Abstract

Physically connected humanoids need consistent dynamics for internal actuator loops, inter-robot forces, and changing ground supports. We extend RoboCompiler with member-wise dynamics assembly, compiling reduced dynamics from rigid bodies, moving actuator parts, and reflected rotor inertias. Compiled body Jacobians and analytic constraint curvature yield an explicit Coriolis factor satisfying the power identity for floating-base quasi-velocities. A two-level reduction retains reusable robot models while composing their supports and hand connections; local inertial updates have rank at most six, and prescribed-acceleration constraint wrenches are affine in actuator efforts. These interfaces support actuator-aware tracking, coupled force allocation, payload updates, and support-mode switching for five hand-linked humanoids. Across 264 feasible states in eight humanoid configurations, normalised acceleration discrepancies remain within $1.6\!\times\!10^{-10}$ against a hard-constraint reference and $1.4\!\times\!10^{-10}$ against a compiler-independent reference; MuJoCo simulations achieve 0.73~mm root-mean-square (RMS) pelvis error in the ring dance and complete side steps through 20 support-mode changes.

0.29

Inertially Significant Humanoid Teleoperation via Whole Body Model Predictive Control and Online Parameter Estimation

cs.RO ·2026-10-15 ·James Foster, Beomyeong Park, Luigi Penco, Robert Griffin
similarity 0.61
Abstract

The effective deployment of humanoid robots in practical tasks of interest will require a capability of sensing and adapting to variations in inertial parameters, as occurs during heavy tool use or when carrying significant payload. Such payloads constitute a significant proportion of the combined payload-robot system, the effects of which cannot be ignored by delegating to feedback control. This paper showcases a general solution to this problem by integrating a whole body model predictive controller (WB-MPC) with an extended Kalman filter (EKF) for online estimation of fully physically consistent time-varying inertial parameters. These estimates are fed through to the WB-MPC's full rigid body dynamics model, resulting in more accurate feedforward torques for task demands under external load. Additionally, a virtual reality (VR) interface is provided that enables an operator to provide task-specific references without regard to payload while delegating dynamic balance to the WB-MPC. The framework is validated with simulation and hardware experiments on a humanoid system.

0.16

BRIDGE: An Open-Source Humanoid Platform via Morphology-Control Co-Design for Physical AI

cs.RO cs.AI ·2026-09-03 ·Jianren Wang, Letian Qian, Zikai Wang, Weiwei Wu, Junjie Zong +2 more
code/data similarity 0.60
Abstract

Developing humanoid robots capable of leveraging human behavioral data is essential for general-purpose embodiment, yet conventional development remains bottlenecked by a decoupled paradigm that isolates hardware design from whole-body control. This approach leads to suboptimal systems that compromise human-like fluidity and agility. To bridge this gap, we introduce a data-driven morphology-control co-design framework that optimizes humanoid morphology for human-like movement. To quantify morphological fidelity, we also introduce a novel metric that jointly considers kinematic retargeting fidelity to human motion and dynamic tracking performance. Our framework achieves state-of-the-art (SOTA) performance across all metrics compared to baseline humanoids (Bumi, K1, and Toddlerbot). Finally, we realize this design in Bridge, an open-source, 88cm-tall humanoid platform released alongside its control policy. We demonstrate that Bridge captures human motion data with superior fidelity, exhibiting exceptional performance across foundational locomotion, robust balance, and highly dynamic maneuvers. Videos and open-source materials: https://sites.google.com/view/bridgerobot.

0.46