CS Paper Radar

Modeling Load-, Velocity-, and Temperature-Dependent Transmission Errors of Cycloidal Drives for Industrial Robots Using Fourier Series

Christian J. E. Bauer, Valentin Kamm, Marcel Dzubba, Lukas Steinle, Armin Lechler, Alexander Verl

cs.RO eess.SPeess.SY ·submitted 2026-09-24 06:43 UTC · v1
publishedunusual

Abstract

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

Comment
7 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-4454
Journal ref
2025 IEEE International Conference on Industrial Technology (ICIT). Wuhan, China: IEEE, Mar. 2025
DOI
10.1109/ICIT63637.2025.10965256

Closest papers

Nearest neighbours by meaning across the whole index.

Transmission Error Compensation for Industrial Robots Using Fourier Series

eess.SY cs.ROeess.SP ·2026-09-24 ·Christian J. E. Bauer, Simon Nowinski, Valentin Kamm, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.67
Abstract · 10 pages, 6 figures, 1 table. Accepted for publication in Annals of Scientific Society for Assembly, Handling and Industrial Robots, 2026. D…

Due to their low accuracy, industrial robots commonly require online teaching after the offline development of a robot program in simulation. The accuracy is limited by compliance and transmission errors in the robot joints. Transmission errors are defined as errors between the load-side angles of the gearboxes and the motor encoder angles. An approach to identify the transmission errors based on laser tracker measurements is presented. The developed velocity-dependent Fourier series model is integrated in a virtual commissioning software as a co-simulated functional mock-up unit. Additionally, it is used to compensate the transmission errors by correcting the setpoint from the computerized numerical control (CNC). The model identification and the compensation are experimentally evaluated with a Stäubli TX2-40 industrial robot. The model has a mean absolute error of 0.114 mrad, and the compensation improves the accuracy by 83.26 % for axis 2 and 49.21 % for axis 3.

0.59

Lubricant Temperature Observer for Gearboxes in Industrial Robots

eess.SY cs.ROeess.SP ·2026-09-24 ·Christian J. E. Bauer, Markus Neher, Valentin Kamm, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.63
Abstract · 8 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-5015

The position and path accuracy of industrial robots is strongly affected by temperature. In particular, temperature-dependent friction and altered hysteresis and transmission errors in the gearboxes are the main causes of these deviations. Since standard industrial robots lack temperature sensors, it is proposed to estimate the gearbox lubricant temperature using observer structures. It is planned to apply the proposed lubricant temperature observer to provide the input for temperature-dependent error compensation for gearboxes in industrial robots. First, a two-state heat transfer model describing the heat transfer from the lubricant through the gearbox housing to the environment is described and identified. It is integrated into a Luenberger observer and a Kalman filter with a correction of the lubricant temperature estimation based on measurements from a housing temperature sensor. Temperature measurements were performed in an experimental setup with a cycloidal gear filled with grease, which is common for industrial robots. Due to its changing viscosity and changing thermal conductivity at different shear rates, it shows a less uniform thermal behavior than gear-oil. For the validation measurements, the developed observers showed a mean absolute error of 1.3 K.

0.79

BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes

cs.RO ·2026-11-18 ·Deepak Kapa, Aman Singh, Saketh Vegesna, Suryank Joshi, Mayank Goswami +1 more
top venuecode/data similarity 0.58
Abstract · 8 pages, 6 figures, 2 tables. Project page: https://deepak-kapa.github.io/PancakeActuator/ Accepted to IEEE Robotics and Automation Letters …

Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.

0.68

Direct Electromechanical Actuation of the Shift Drum in Non-Synchronized Motorcycle Transmissions: From Actuator Sizing and Electronics Design to Closed-Loop Position Control

eess.SY ·2026-10-12 ·Johannes Stockhammer
unusual similarity 0.45
Abstract · Original German title (2019): Entwickeln eines automatisierten Schaltgetriebes fuer Motorraeder. Diploma thesis, Westsaechsische Hochschule …

This thesis presents the direct electromechanical actuation of the shift drum in a non-synchronized motorcycle transmission. A DC motor drives the shift drum through a self-locking worm gear, so the entire foot shift mechanism is eliminated. As a reference, 84 manual gear changes of a large-displacement series-production motorcycle were measured on a chassis dynamometer; the mean shift time is 80 ms for upshifts and 92 ms for downshifts. The system design covers the complete chain from the mechanics to the software. The actuator motor is sized from inertia, friction and gear ratio. A dedicated shift controller is developed with supply filtering, signal conditioning for the position sensor and the incremental encoder, an H-bridge motor driver and a custom circuit board based on a SAMD21 microcontroller. The embedded firmware implements position control of the shift drum with a proportional controller, without inner speed or current loops. On a gearbox test rig, a gear change is completed in less than 80 ms without overshoot in a single measurement, below the mean of the manual reference shifts. The analysis reveals a trade-off in the choice of the worm gear ratio: at a ratio of 30, about 93% of the motor torque is needed to accelerate the motor shaft and the worm. A ratio of about 8 halves the required torque, but the worm gear then loses its self-locking. The measured shift times are published as an open dataset.

0.34

A Harmonic-Regression ARMA model for rotating machinery dynamics identification and fault detection under varying conditions

eess.SP ·2026-09-23 ·Dimitrios M. Bourdalos, John S. Sakellariou, Spilios D. Fassois
published similarity 0.44
Abstract · Accepted for publication in the Proceedings of the International Conference on Noise and Vibration Engineering (ISMA 2026), Leuven, Belgium,…

Fault detection in rotating machinery under varying operating conditions remains a challenging problem. Existing approaches are mainly based either on non-parametric vibration signal representations, parametric deep learning models, or on parametric ARMA-type models. While deep learning approaches often lack transparency and require large training datasets, ARMA-type models rely on the assumption of a purely rational spectrum, which can be restrictive for rotating machinery vibration signals exhibiting mixed spectral characteristics. To address these limitations, a novel Harmonic Regression ARMA (HR-ARMA) model is presented for rotating machinery dynamics identification, which combines an explicit harmonic regression part for representing the dominant deterministic cyclical components with an ARMA part for the remaining broadband stochastic dynamics. Based on this model and within a Multiple Model framework, fault detection is achieved under varying operating conditions. The HR-ARMA modelling performance is validated through simulation and experimental studies on a single-stage gearbox, demonstrating accurate representation of both cyclical and broadband dynamics, improved parsimony and significantly higher fault detection performance compared with conventional ARMA models, achieving at least 98% True Positive Rate at 5% False Positive Rate in the experimental study.

0.39

Design and Experimental Validation of a 3D Printed Torsional Series Elastic Actuator for Safe Human Robot Interaction

cs.RO ·2026-09-16 ·Joel Hidalgo Pisco, Melissa Cobos Condo, Luigi Miranda, Dennys Paillacho
published similarity 0.41
Abstract

Ensuring intrinsic safety in physical human robot interaction (pHRI) is a critical requirement for social and service robots. While Series Elastic Actuators (SEAs) offer hardware based compliance, traditional metallic designs often require complex, multi part assemblies. This paper presents the design, finite element analysis (FEA), and experimental validation of a low stiffness, torsional spring for SEAs, manufactured via 3D printed thermoplastic polyurethane (TPU). The compliant element exhibits a highly linear torque deformation response (Ks = 0.066 Nm/degree), matching numerical predictions with under 3% deviation, a variance attributed to FDM structural anisotropy. To accommodate external interactions using standard position limited servomotors, a hybrid position controller with torque threshold switching was implemented. Experimental evaluations demonstrate the system ability to accurately track non stationary trajectories and safely yield to external disturbances. Furthermore, the inherent material damping of the TPU acts as a passive low pass filter, preventing high frequency oscillations during control mode transitions. The proposed architecture offers a cost effective, reliable, and easily manufacturable solution for safe pHRI.

0.32

SHAFT: A Slack-Compensating, Helical-Buckling-Attenuating Flexible-Shaft Transmission for Lightweight Multi-DoF Manipulation

cs.RO ·2026-09-19 ·Tomoya Takahashi, Moses Gladson Selvamuthu, Richiro Tadakuma, Kazutoshi Tanaka
published similarity 0.40
Abstract · 9 pages, 14 figures, submitted as proceedings of IROS2026

Lightweight and slim manipulators enable safe operation in human living environments. Proximal actuation using remote transmission mechanisms, such as wire-driven or Bowden cables, effectively reduces inertia and arm size by relocating motors near the base and transmitting torque to distal joints. Existing approaches either increase mass through additional components, such as pulleys for direction changes, or suffer from reduced transmission efficiency due to friction losses. Flexible shaft transmission avoids both mass increase and excessive friction losses, but faces increasing angular transmission error due to helical buckling caused by slack generated at joint bending. To address this problem, we propose SHAFT: a Slack-compensating, Helical-buckling-Attenuating Flexible- shaft Transmission mechanism. This mechanism compensates for slack through a proximal tensioner, improving the angular transmission error and efficiency of flexible shaft transmission without increasing the moving mass of the arm section. In a transmission path containing four 90-degree bends, the proposed mechanism demonstrated approximately 30% higher efficiency and approximately 65% lower angular transmission error compared to a flexible shaft transmission without a tensioner. Using this mechanism, we fabricated a 6-Degree-of-Freedom (DoF) arm with a 1-DoF gripper manipulator consisting of a rotary module housing motors with a tensioner, and a 280 g weight for the arm module. The proposed manipulator represents a novel remote actuation system for achieving lightweight construction with high efficiency, contributing to the acceleration of safe robot deployment in human environments.

0.42

A Second Torque Port for Series Elastic Actuators: Parallel-Integrated Design and Time-Scale Torque Allocation

cs.RO eess.SY ·2026-09-25 ·Donghao Jia, Xiubo Xia, Junhang Liu, Zeyu Zhu, Xiaoyu Geng +1 more
unusual similarity 0.38
Abstract · 8 pages, 9 figures, 1 table. Submitted to IEEE Robotics and Automation Letters

A series elastic actuator has a single torque port and pays for it twice: the geared motor must swing its own reflected inertia through the spring, so the amplitude it delivers collapses as $ω^{-2}$ in the command frequency $ω$ once it saturates, while commands below the transmission's breakaway friction never arrive at all. This letter opens a second torque port on the load side, placing a frameless direct-drive micro motor in parallel with a fixed-stiffness spring -- a parallel-integrated SEA, or Pi-SEA, whose delivered torque is read from spring deflection and micro current without a sensor -- and dividing the commanded torque between the two channels by time scale rather than by filter design. The micro torque loop is the fast subsystem, which makes the closed loop singularly perturbed and turns the separation the channels need into a bound to check rather than a crossover to tune; a leaky mid-ranging integrator returns the steady load to the spring; and the amplitude ceiling, read backwards, becomes a closed-form sizing rule that matches spring, geared motor and micro motor to the amplitudes and frequencies an application asks for. Against SEAs, the Pi-SEA widens the tracked band at small amplitudes and lowers the residual the joint imposes on its environment, each by an order of magnitude.

0.29