CS Paper Radar

Transmission Error Compensation for Industrial Robots Using Fourier Series

Christian J. E. Bauer, Simon Nowinski, Valentin Kamm, Lukas Steinle, Armin Lechler, Alexander Verl

eess.SY cs.ROeess.SP ·submitted 2026-09-24 06:46 UTC · v1
publishedunusual

Abstract

Due to their low accuracy, industrial robots commonly require online teaching after the offline development of a robot program in simulation. The accuracy is limited by compliance and transmission errors in the robot joints. Transmission errors are defined as errors between the load-side angles of the gearboxes and the motor encoder angles. An approach to identify the transmission errors based on laser tracker measurements is presented. The developed velocity-dependent Fourier series model is integrated in a virtual commissioning software as a co-simulated functional mock-up unit. Additionally, it is used to compensate the transmission errors by correcting the setpoint from the computerized numerical control (CNC). The model identification and the compensation are experimentally evaluated with a Stäubli TX2-40 industrial robot. The model has a mean absolute error of 0.114 mrad, and the compensation improves the accuracy by 83.26 % for axis 2 and 49.21 % for axis 3.

Comment
10 pages, 6 figures, 1 table. Accepted for publication in Annals of Scientific Society for Assembly, Handling and Industrial Robots, 2026. Dataset available on https://doi.org/10.18419/DARUS-5760

Closest papers

Nearest neighbours by meaning across the whole index.

Modeling Load-, Velocity-, and Temperature-Dependent Transmission Errors of Cycloidal Drives for Industrial Robots Using Fourier Series

cs.RO eess.SPeess.SY ·2026-09-24 ·Christian J. E. Bauer, Valentin Kamm, Marcel Dzubba, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.67
Abstract · 7 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-4454

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

0.85

Lubricant Temperature Observer for Gearboxes in Industrial Robots

eess.SY cs.ROeess.SP ·2026-09-24 ·Christian J. E. Bauer, Markus Neher, Valentin Kamm, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.55
Abstract · 8 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-5015

The position and path accuracy of industrial robots is strongly affected by temperature. In particular, temperature-dependent friction and altered hysteresis and transmission errors in the gearboxes are the main causes of these deviations. Since standard industrial robots lack temperature sensors, it is proposed to estimate the gearbox lubricant temperature using observer structures. It is planned to apply the proposed lubricant temperature observer to provide the input for temperature-dependent error compensation for gearboxes in industrial robots. First, a two-state heat transfer model describing the heat transfer from the lubricant through the gearbox housing to the environment is described and identified. It is integrated into a Luenberger observer and a Kalman filter with a correction of the lubricant temperature estimation based on measurements from a housing temperature sensor. Temperature measurements were performed in an experimental setup with a cycloidal gear filled with grease, which is common for industrial robots. Due to its changing viscosity and changing thermal conductivity at different shear rates, it shows a less uniform thermal behavior than gear-oil. For the validation measurements, the developed observers showed a mean absolute error of 1.3 K.

0.79

Residual Reinforcement Learning for Visual Servo Control with Zero-Shot Sim-to-Real Transfer

cs.RO eess.SY ·2026-11-14 ·Mahdi Nobar, Alisa Rupenyan, John Lygeros, Jürg Keller
similarity 0.50
Abstract · This manuscript is currently under review in IEEE Robotics and Automation Letters (RA-L)

We address tracking a moving object on a conveyor with a Franka Emika Panda robot arm, despite an imprecise digital twin, measurement errors, and noise. Our novel approach augments a loop-shaped inverse-Jacobian PI controller with a residual policy learned via Soft Actor-Critic in the digital twin. A delay-compensated Kalman filter fuses out-of-sequence camera measurements to provide latency-aware moving target position estimates. We compare the achieved performance to a performance bound for a class of model-based controllers derived from a frequency-domain sensitivity analysis, quantifying the minimum achievable error imposed by uncertain kinematic model mismatch. Simulation and hardware experiments indicate that our residual policy drives tracking error below the bound. Across conveyor speeds (27.9-41.8 mm/s), our method reduces mean tracking errors from 1.1-1.4 mm (baseline inverse-Jacobian PI) to 0.3-0.7 mm. These results show that learning residual corrections in a limited-fidelity simulator, combined with delay compensation, can substantially improve model-based control under modeling and measurement uncertainties while maintaining reliable sim-to-real transfer.

0.23

A comparative study on the accuracy & repeatability of mobile robotic platforms for the delivery of precision NDE measurement

cs.RO ·2026-09-03 ·SeyedMohammadAmin Nabi Pour, S. Gareth Pierce, Randika Vithanage, Ehsan Mohseni, David Carswell +1 more
similarity 0.50
Abstract

Mobile robotic platforms offer a flexible alternative to fixed manipulators for non-destructive evaluation (NDE) of large aerospace structures, but their base-positioning accuracy and how that accuracy should inform deployment have not been assessed under a common, externally referenced protocol. This work presents a laser tracker-based evaluation workflow (ground truth approximately 6 micrometers) that measures the static and segmented trajectory positioning accuracy of five commercial mobile platforms (KUKA KMP-1500, KUKA KMR, MiR250, Boston Dynamics Spot, Clearpath Husky) under a common protocol. A coupled multi-corner calibration recovers the laser-to-robot transformation and reflector offsets; ordinary least squares over all poses is used, with robust estimation retained only as a blunder check. Static positioning accuracy ranged from a median of 8.2 mm (KMP-1500) to 63.5 mm (Spot), with the wheel-odometry-only Husky uncalibratable. Dynamic path following was characterised by cross-track error; the component was insensitive to temporal alignment, which ranged from 6.9 mm (KMP-1500) to 112.1 mm (Spot). Both accuracy and calibratability tracked localisation capability, from the newest LiDAR SLAM platform to map-free visual odometry. No configuration meets the 0.2 to 1.0 mm aerospace NDE tolerance from the base alone; the results are framed as a design input that sizes the supplementary sensing each platform requires: roughly one order of magnitude for the best platform and nearly two for the worst, providing a reproducible basis for platform selection rather than a feasibility claim.

0.16

Inertially Significant Humanoid Teleoperation via Whole Body Model Predictive Control and Online Parameter Estimation

cs.RO ·2026-10-15 ·James Foster, Beomyeong Park, Luigi Penco, Robert Griffin
similarity 0.45
Abstract

The effective deployment of humanoid robots in practical tasks of interest will require a capability of sensing and adapting to variations in inertial parameters, as occurs during heavy tool use or when carrying significant payload. Such payloads constitute a significant proportion of the combined payload-robot system, the effects of which cannot be ignored by delegating to feedback control. This paper showcases a general solution to this problem by integrating a whole body model predictive controller (WB-MPC) with an extended Kalman filter (EKF) for online estimation of fully physically consistent time-varying inertial parameters. These estimates are fed through to the WB-MPC's full rigid body dynamics model, resulting in more accurate feedforward torques for task demands under external load. Additionally, a virtual reality (VR) interface is provided that enables an operator to provide task-specific references without regard to payload while delegating dynamic balance to the WB-MPC. The framework is validated with simulation and hardware experiments on a humanoid system.

0.16

Real-Time Reference Shaping for Servo Systems

eess.SY ·2026-08-31 ·Zehui Lu, Yebin Wang, Go Sato, Fujita Tomoya
similarity 0.44
Abstract

This paper addresses real-time motion planning for servo systems subject to nonlinear, state-dependent actuator constraints. A reference reshaping method is proposed that combines analytical optimality with high computational efficiency. Using Karush-Kuhn-Tucker conditions, the problem structure is explicitly characterized, and it is shown that the optimal solution lies within a finite set of candidate points. The complete solution set is constructed via closed-form expressions and a small-scale eigenvalue problem, yielding a deterministic algorithm that recovers the exact optimal solution without iterative optimization or root-finding. To address kinematic mismatch induced by aggressive commands, a real-time trajectory compensator is introduced to correct accumulated position error while preserving feasibility. Simulation results demonstrate significant computational speed improvements over existing methods, enabling real-time implementation at frequencies approaching 100 kHz.

0.24

Genie Sim Benchmark: Real-to-Sim Fidelity and Evaluation

cs.RO ·2026-11-11 ·Di Yang, Da Huang, Yang Lv, Fan Yang, Yi Lu +6 more
benchmark similarity 0.43
Abstract

We evaluate Genie Sim Benchmark through paired real-simulation tasks and complementary system-identification studies. Across 22 robot-task pairs spanning 16 task names, task-specific pi0.5 policies fine-tuned on real-robot data achieve a descriptive Score correlation of 0.9686, MAE 0.0405, RMSE 0.0520, with simulation-real differences from -0.110 to +0.080. G2 crsB experiments assess long-horizon closed-loop position and joint-side torque agreement, while five representative object cases examine identification and cross-engine contact transfer. A separate 32.6503 s teleoperation trajectory, excluded from mechanical identification and servo-gain search, evaluates external position targets through simulated motion-controller command shaping and a calibrated position servo. Across both arms, per-joint position RMSE spans 0.00614-0.03522 rad and current-derived torque RMSE spans 0.73545-4.00099 N m. Native PhysX adaptations recover three recorded interaction tasks, with case-dependent alignment gains. These results support task-specific simulation evaluation through joint assessment of task outcomes and physical-response consistency.

0.17

Online Joint Calibration of Steering Offset and Planar LiDAR Extrinsics for Wheeled Mobile Robots

cs.RO ·2026-08-27 ·Subodh Mishra, Arindam Dhar, Suprotim Majumdar, Naveen Arulselvan
similarity 0.43
Abstract

Accurate steering sensing and LiDAR-to-vehicle extrinsics are crucial for reliable path tracking in warehouse mobile robots (WMRs); miscalibration often leads to snaking, weaving, and elevated cross-track error (CTE). In practice, steering ``zero'' is commonly set manually (e.g., eyeballing straightness via a PS4 joystick), while LiDAR extrinsics are assumed from CAD and may drift after maintenance. Such static, manual procedures frequently cause miscalibration in safety-critical environments. This paper presents an Extended Kalman Filter (EKF)--based method for online estimation of steering offset and planar LiDAR extrinsics within a bicycle-kinematics model, providing a principled alternative to manual calibration. Experiments on real datasets show that correcting steering offset reduces CTE substantially, validating the effectiveness of the proposed approach.

0.29