CS Paper Radar

Lubricant Temperature Observer for Gearboxes in Industrial Robots

Christian J. E. Bauer, Markus Neher, Valentin Kamm, Lukas Steinle, Armin Lechler, Alexander Verl

eess.SY cs.ROeess.SP ·submitted 2026-09-24 06:45 UTC · v1
publishedunusual

Abstract

The position and path accuracy of industrial robots is strongly affected by temperature. In particular, temperature-dependent friction and altered hysteresis and transmission errors in the gearboxes are the main causes of these deviations. Since standard industrial robots lack temperature sensors, it is proposed to estimate the gearbox lubricant temperature using observer structures. It is planned to apply the proposed lubricant temperature observer to provide the input for temperature-dependent error compensation for gearboxes in industrial robots. First, a two-state heat transfer model describing the heat transfer from the lubricant through the gearbox housing to the environment is described and identified. It is integrated into a Luenberger observer and a Kalman filter with a correction of the lubricant temperature estimation based on measurements from a housing temperature sensor. Temperature measurements were performed in an experimental setup with a cycloidal gear filled with grease, which is common for industrial robots. Due to its changing viscosity and changing thermal conductivity at different shear rates, it shows a less uniform thermal behavior than gear-oil. For the validation measurements, the developed observers showed a mean absolute error of 1.3 K.

Comment
8 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-5015
Journal ref
IECON 2025 - 51st Annual Conference of the IEEE Industrial Electronics Society. Madrid, Spain: IEEE, Oct. 2025
DOI
10.1109/IECON58223.2025.11221072

Closest papers

Nearest neighbours by meaning across the whole index.

Modeling Load-, Velocity-, and Temperature-Dependent Transmission Errors of Cycloidal Drives for Industrial Robots Using Fourier Series

cs.RO eess.SPeess.SY ·2026-09-24 ·Christian J. E. Bauer, Valentin Kamm, Marcel Dzubba, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.63
Abstract · 7 pages, 7 figures, 2 tables. Dataset available on https://doi.org/10.18419/DARUS-4454

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

0.85

Transmission Error Compensation for Industrial Robots Using Fourier Series

eess.SY cs.ROeess.SP ·2026-09-24 ·Christian J. E. Bauer, Simon Nowinski, Valentin Kamm, Lukas Steinle, Armin Lechler +1 more
publishedunusual similarity 0.55
Abstract · 10 pages, 6 figures, 1 table. Accepted for publication in Annals of Scientific Society for Assembly, Handling and Industrial Robots, 2026. D…

Due to their low accuracy, industrial robots commonly require online teaching after the offline development of a robot program in simulation. The accuracy is limited by compliance and transmission errors in the robot joints. Transmission errors are defined as errors between the load-side angles of the gearboxes and the motor encoder angles. An approach to identify the transmission errors based on laser tracker measurements is presented. The developed velocity-dependent Fourier series model is integrated in a virtual commissioning software as a co-simulated functional mock-up unit. Additionally, it is used to compensate the transmission errors by correcting the setpoint from the computerized numerical control (CNC). The model identification and the compensation are experimentally evaluated with a Stäubli TX2-40 industrial robot. The model has a mean absolute error of 0.114 mrad, and the compensation improves the accuracy by 83.26 % for axis 2 and 49.21 % for axis 3.

0.59

KOOPMAN-Luenberger Observer Design for Nonlinear Systems with Application to the Monitoring of a Latent Thermal Energy Storage

eess.SY ·2026-08-11 ·Mustapha Habib, Dario Aguiar, Esther Kieseritzky, Tilman Barz, Qian Wang
similarity 0.44
Abstract

State estimation for nonlinear dynamical systems remains a fundamental challenge, particularly when measurements are sparse and internal states are inaccessible. This work presents a KOOPMAN-based Linear State Observer (KOOPMAN-LSO) design framework that enables linear observer synthesis for nonlinear systems through KOOPMAN operator theory. The nonlinear dynamics are lifted into a higher-dimensional observable space using physics-informed basis functions, where a linear predictor with control is identified via extended dynamic mode decomposition with control (eDMDc). A discrete-time Luenberger observer is then constructed in the lifted space, and the observer gain is obtained through a dual linear - quadratic regulator (LQR) formulation to ensure stable and tunable estimation error dynamics. The proposed framework combines the representational capability of KOOPMAN lifting with the simplicity and computational efficiency of linear observer design, providing a systematic approach for nonlinear state estimation under limited sensing. Its effectiveness is demonstrated on a latent thermal energy storage (LTES) system based on phase-change materials (PCM), where internal temperature states are not directly measurable. Experimental results under varying operating conditions show accurate reconstruction of unmeasured states from limited output measurements, illustrating the potential of KOOPMAN-LSO design for practical nonlinear systems. The proposed approach achieves high-fidelity reconstruction with an RMSE as low as 0.0819 °C for the LTES outlet temperature and generally below 1.0 °C for observable internal PCM temperatures.

0.04

Direct Electromechanical Actuation of the Shift Drum in Non-Synchronized Motorcycle Transmissions: From Actuator Sizing and Electronics Design to Closed-Loop Position Control

eess.SY ·2026-10-12 ·Johannes Stockhammer
unusual similarity 0.44
Abstract · Original German title (2019): Entwickeln eines automatisierten Schaltgetriebes fuer Motorraeder. Diploma thesis, Westsaechsische Hochschule …

This thesis presents the direct electromechanical actuation of the shift drum in a non-synchronized motorcycle transmission. A DC motor drives the shift drum through a self-locking worm gear, so the entire foot shift mechanism is eliminated. As a reference, 84 manual gear changes of a large-displacement series-production motorcycle were measured on a chassis dynamometer; the mean shift time is 80 ms for upshifts and 92 ms for downshifts. The system design covers the complete chain from the mechanics to the software. The actuator motor is sized from inertia, friction and gear ratio. A dedicated shift controller is developed with supply filtering, signal conditioning for the position sensor and the incremental encoder, an H-bridge motor driver and a custom circuit board based on a SAMD21 microcontroller. The embedded firmware implements position control of the shift drum with a proportional controller, without inner speed or current loops. On a gearbox test rig, a gear change is completed in less than 80 ms without overshoot in a single measurement, below the mean of the manual reference shifts. The analysis reveals a trade-off in the choice of the worm gear ratio: at a ratio of 30, about 93% of the motor torque is needed to accelerate the motor shaft and the worm. A ratio of about 8 halves the required torque, but the worm gear then loses its self-locking. The measured shift times are published as an open dataset.

0.34

Temperature-Dependent Multiphysics Modeling of Additive Friction Stir Deposition Using Multi-Task Coupled Physics-Informed Neural Networks

cs.CE physics.comp-ph ·2026-10-02 ·Dhrubajyoti Gupta, Nikhil Gotawala, Raghav Gnanasambandam, Rohit Kannan, Jian Yu +2 more
benchmark similarity 0.42
Abstract · 14 pages, 12 figures, 7 tables

Additive friction stir deposition (AFSD) involves coupled thermal and material-flow fields governed by frictional heating, plastic deformation, and tool-imposed boundary conditions. High-fidelity finite-volume methods (FVMs) can resolve these fields but are computationally expensive, while constant-property approximations can distort the predicted thermo-mechanical response. This work develops a steady-state multi-task coupled physics-informed neural network (MCoPINN) to predict three-dimensional temperature and material-flow fields while reconstructing temperature-dependent thermal conductivity, density, and specific heat from sparse property measurements. A theoretical analysis decomposes prediction error into property reconstruction and neural field-solver contributions and characterizes the discrepancy associated with constant-property models. A controlled one-dimensional nonlinear-conduction study evaluates property reconstruction under sparse measurements. The framework is then evaluated for AFSD against a temperature-dependent FVM benchmark and experimental thermocouple measurements. MCoPINN reproduces the reference thermal and material-flow fields and reduces average temperature root-mean-square error from 50.13 K for the constant-property CoPINN to 30.28 K across four traverse speeds. MCoPINN requires approximately 8.5 hours of training per condition, compared with 52 hours for the FVM benchmark. These results demonstrate computationally efficient, physics-coupled prediction with temperature-dependent material properties.

0.34

BiPathCPG: A Novel Load-Sharing Design Architecture for Compound Planetary Gearboxes

cs.RO ·2026-11-18 ·Deepak Kapa, Aman Singh, Saketh Vegesna, Suryank Joshi, Mayank Goswami +1 more
top venuecode/data similarity 0.42
Abstract · 8 pages, 6 figures, 2 tables. Project page: https://deepak-kapa.github.io/PancakeActuator/ Accepted to IEEE Robotics and Automation Letters …

Quasi-Direct Drive (QDD) actuators are widely used in legged robots due to their low reflected inertia, high backdrivability, and high torque density, commonly employing planetary or cycloidal gearboxes. Single-stage planetary gearboxes offer high efficiency but limited torque density; multi-stage designs improve torque density at the cost of efficiency; and cycloidal gearboxes provide high stiffness but suffer from torque ripple. Compound Planetary Gearboxes (CPG) offer a compromise, but conventional designs result in increased actuator width, mass, and reduced torsional stiffness in 3D-printed actuators. This paper proposes the BiPath Compound Planetary Gearbox (BiPathCPG), a novel architecture that introduces an idle second-stage sun gear and load-sharing second-stage planets within the otherwise unused space of a conventional CPG to simultaneously improve stiffness, reduce actuator width, and reduce mass. An optimization framework computes BiPathCPG parameters for a given motor and target gear ratio. The architecture is validated through a 3D-printed proof-of-concept actuator design, benchmarked against a conventional CPG using custom-built test rigs. The BiPathCPG achieves a torsional stiffness of 1394 Nm/rad, a 1.70x improvement over the conventional CPG, with a 32% reduction in backlash, 25 g lower mass, and approximately 6.4 mm reduction in axial width, while achieving a peak stall torque of 36.49 Nm.

0.68

A Disk-Shaped Magnetoelastic Torque Sensor for Robotic Joints Using Permanent Magnetization

cs.RO eess.SY ·2026-09-27 ·Bruno Brajon, Enrico Gasparin, Nicole Yazigy, Lisa Salamin, Florian Copt +3 more
similarity 0.39
Abstract

Direct torque sensing is a growing need in the robotics community to enable precise control and interactions where torque estimation from motor current is not sufficient. This paper presents a novel disk-shaped magnetoelastic torque sensor with a compact axial envelope of about 1 cm, suitable for integration in robotic joints. A four-magnetometer architecture is used to measure the field modulated by the stress affecting a narrow magnetized region while rejecting the effects of parasitic cross forces. A custom-designed magnetic shield enhances the torque sensitivity while reducing the external stray fields by a factor 7x. The device measures the torque with an accuracy of 1.34 %FS relative to the 50 Nm full scale (FS). The paper details the development of the sensor through the mechanical design, the magnetization procedure, and the experimental validation. The results demonstrate the potential of the proposed sensor for robotic applications.

0.24

SCRUB: Contact-Based Surface-Frame Estimation for Force-Motion Control with an Armless Quadruped

cs.RO ·2026-11-04 ·Sourav Selvaraj, Juan Pablo Espinosa Chessal, Mahdi Agheli
similarity 0.38
Abstract · 8 pages, 6 figures, 4 tables

Wiping, sanding, and inspection robots press a sliding tool on a surface with controlled force. Controlling that force needs the surface normal, which is unknown on real-world, unmapped surfaces. Surface-normal estimators can help estimate the surface normal, but they either need a friction model or assume that the instantaneous tool velocity lies along the surface; however, walking violates this assumption. We propose SCRUB, a contact-based surface-frame estimator, which lets an armless quadruped slide a body-mounted tool along near-vertical surfaces in the absence of known, axis-aligned, or vision-predicted normals. SCRUB's predictive controller presses and slides the tool using a Kalman-filter estimate of the normal from two cues: 1) A force cue measures the estimate's tilt across the motion. If friction directly opposes the motion, the cue is zero exactly when that tilt is zero, for any friction coefficient. However, if the cue's sliding direction is wrong, friction appears as a false tilt. 2) A velocity cue measures tilt along the motion. Walking and pressing move the tool in and out. SCRUB therefore subtracts the commanded press rate from the tool velocity, averages the result over each gait cycle, and treats this mean as lying along the surface. On Unitree Go1 hardware at nominal speed and load, SCRUB completed every wall traverse and column orbit. No orbit completed with either cue removed, without gait averaging, or with a fixed normal.

0.21