CS Paper Radar

A Disk-Shaped Magnetoelastic Torque Sensor for Robotic Joints Using Permanent Magnetization

Bruno Brajon, Enrico Gasparin, Nicole Yazigy, Lisa Salamin, Florian Copt, Guzmán Borque Gallego, Elias Klauser, Gaël Close

cs.RO eess.SY ·submitted 2026-09-27 13:08 UTC · v2

Abstract

Direct torque sensing is a growing need in the robotics community to enable precise control and interactions where torque estimation from motor current is not sufficient. This paper presents a novel disk-shaped magnetoelastic torque sensor with a compact axial envelope of about 1 cm, suitable for integration in robotic joints. A four-magnetometer architecture is used to measure the field modulated by the stress affecting a narrow magnetized region while rejecting the effects of parasitic cross forces. A custom-designed magnetic shield enhances the torque sensitivity while reducing the external stray fields by a factor 7x. The device measures the torque with an accuracy of 1.34 %FS relative to the 50 Nm full scale (FS). The paper details the development of the sensor through the mechanical design, the magnetization procedure, and the experimental validation. The results demonstrate the potential of the proposed sensor for robotic applications.

Closest papers

Nearest neighbours by meaning across the whole index.

MagCilia: A Compact Magnetociliary Tactile Sensor with 3D Force Sensing for Robotic Contact Perception and Grasping Feedback

cs.RO ·2026-10-07 ·Yu Feng, Hao Wu, Haotian Guo, Haoming Liu, William Su +5 more
highly cited similarity 0.61
Abstract

Robotic grasping and surface exploration benefit from simultaneous measurement of normal and tangential forces and from surface information obtained through contact. Here, we present a compact magnetociliary tactile sensor (MagCilia) that combines a flexible magnetic-cilia structure with a Hall sensor for 3D force sensing. Quasi-static finite element analysis is used to investigate structural deformation and magnetic responses under multidirectional loading. To reconstruct forces from the coupled magnetic channels, we propose causal history fusion regression (CHFR), which combines current magnetic-field measurements with their recent changes. Five-fold cross-validation grouped by calibration record yields root-mean-square errors of 0.40, 0.57, and 0.69 N for Fx, Fy, and Fz, respectively, with corresponding coefficients of determination of 0.93, 0.90, and 0.92. Robotic experiments demonstrate tangential-force-guided gripper adjustment and multi-axis load monitoring under external perturbations. Frequency-domain features of the reconstructed forces distinguish six surface categories with 99.39% accuracy in three-fold cross-validation grouped by acquisition session. An online robotic demonstration additionally identifies all six tested surfaces. These results demonstrate 3D force reconstruction, grasping feedback, and surface recognition using a single compact tactile unit.

0.58

Magnetic based In-situ Self 3D Pose Estimation for a Modular Soft Tendon-Driven Continuum Robot via IMU-Fusion

cs.RO eess.SPeess.SY ·2026-09-30 ·Zheng Cao, Guo Ning Sue, Xiangyun Bu, David Quinn, Junzhe Hu +1 more
similarity 0.60
Abstract

Continuum robots are well suited for gentle manipulation because of their inherent compliance and ability to adapt to complex environments. However, their continuously deformable structure makes accurate configuration estimation challenging, particularly when external vision systems are unavailable or obstructed. In this work, we present an embedded pose sensing framework that combines inertial measurement units (IMUs) and active magnetic fields to estimate the robot configuration without relying on external cameras. The angular measurements from the IMU and magnetic-field references are fused to improve local orientation estimation and reduce accumulated orientation error during operation. This pose sensing scheme achieves an update rate of 16.7~Hz, allowing real-time feedback. The proposed system is experimentally validated through closed-loop control, where the estimated robot configuration is used to maintain the end-effector at a desired position while interacting with an object. These results demonstrate the potential of distributed magnetic--inertial sensing for real-time pose estimation and closed-loop control of continuum robots.

0.11

Hall Effect-Based Tactile Force Detection Sensor for Robot-Assisted Minimally Invasive Surgery

cs.RO ·2026-10-07 ·Charles DeLorey, Michael Brockdorff, Adam Metcalf, Benjamin Calmé, Pietro Valdastri +1 more
similarity 0.58
Abstract · 9 pages, 12 figures

Robotic minimally invasive surgery has revolutionized surgical practice. However, as the surgeons are mechanically separated from the surgical tools, loss of tactile feedback occurs. We present a compact force sensor with three, millimeter scale sensing elements (taxels) that can be affixed to the grasping face of a robotic surgical tool. The sensor features a miniaturized design using Hall effect sensors and magnets embedded in a deformable elastomer contact layer. Sensor calibration is achieved with a 6 degree of freedom (DoF) parallel robot. Each taxel can detect applied normal and shear forces with average RMSE of 2.133 kPa. The calibrated sensor was validated on phantom and ex vivo porcine tissue, demonstrating tactile sensing during retraction as well as slip. This work introduces a small-scale Hall effect based tactile sensor, enabling sensing for force-sensitive robotic surgical applications.

0.17

Magnet-Aware Control of Legged Robots

cs.RO ·2026-10-06 ·J. Playan Garai, S. B. Djuve, C. McGreavy, M. Khadiv
similarity 0.56
Abstract

Autonomous robots can increase uptime and reduce human exposure in Big Science facilities, but strong magnetic fields needed for their operation corrupt sensors and induce pose-dependent mechanical wrenches that destabilize robots and challenge conventional reactive controllers. This paper presents a control framework for modeling, estimating, and dynamically compensating for spatially varying magnetic wrenches acting on legged robots to improve robustness in these fields. We introduce a custom physics plugin for the MuJoCo simulator to model magnetic forces on rigid-body elements, alongside an inverse field-estimation framework to infer the latent magnetic field directly from quadruped dynamic responses and any number of sensor readings. Furthermore, we develop a Magnet-Aware Model Predictive Control (MPC) and Whole-Body Control (WBC) architecture that predicts and counteracts magnetic perturbations during locomotion to increase the range of magnetic fields in which the robot can operate. The effectiveness of the framework is validated through both simulation and physical hardware experiments. We show our method increases the the maximum rejectable disturbances from magnetic field in the force space by a factor of 2.5 and and between 1.6-2 times in torque space compared to a non-compensated system. Within the proposed magnetic field, this constitutes an increase in the area in which the robot can operate by 29,34% of which 10,84% would have previously caused an immediate collapse to non-compensated controllers.

0.28

A robust single-sensing-element tactile sensor for concurrent pressure and tackiness detection with real-time signal decoupling capability

cs.RO cond-mat.mtrl-sci ·2026-09-29 ·Ying Yang, Mingwei Gu, Jia-Sen Xie, Xingyu Ma, Yan-Na Lu +6 more
similarity 0.56
Abstract

Integrating tackiness sensation into the artificial skin of humanoid robots significantly enhances their cognitive and operational capabilities. However existing tactile sensors face challenges in decoupling of the multimodal signal and stability. Here we present a surface-soft tactile sensor that incorporates a Hall effect sensor and a soft magnetic composite within a robust elastic framework. The sensor surface indents under pressure and bulges prominently when retracted from sticky surfaces dynamically altering the Hall sensor-magnet distance. This generates whole-process-traceable and baseline-separated signals enabling real-time differentiation between pressure and pull-off force. This single-sensing-element design facilitates bimodal sensing at the same contact spot while eliminate stress cross-talk enhancing both accuracy and sensitivity. The fusion of a robust framework and magneto-mechanical sensing mechanism equips the sensor with exceptional reliability and excellent signal baseline stability. This tactile sensor holds substantial potential for advancing robotic capabilities in evaluating adhesive properties monitoring rubber aging precisely handling lightweight objects and cognizing natural objects surface characteristics.

0.20

A Conveyor Belt Mechanism for Repositionable Magnetic Coupling Between Continuum Robots

cs.RO ·2026-10-29 ·Ella Walsh, Eric Diller, Jessica Burgner-Kahrs
similarity 0.55
Abstract · 7 pages, 10 figures

This work proposes a novel conveyor belt mechanism enabling continuous, active repositioning of functional elements along the body of a tendon-driven continuum robot. Up to three conveyor belt mechanisms are integrated within a 9 mm diameter continuum robot. We demonstrate equivalent or reduced conveyor belt actuation forces compared to robot tendon actuation forces. As a case study, we mount permanent magnets along two conveyor belts, and demonstrate actively reconfigurable inter-robot coupling. Coupling point location and quantity can be adjusted during robot operation to actively tune the effective stiffness of the coupled multi-robot system. We show that effective stiffness follows a predictable inverse-cubic relationship with coupling location, and increases with the number of coupling points. These findings demonstrate that the conveyor belt mechanism enables active functional element repositioning for changing tasks requirements, with magnetic inter-robot coupling as one proof-of-concept.

0.28

Capstan-driven Continuum Surgical Robot: Design, Modeling, and Perception

cs.RO ·2026-08-13 ·Gang Zhang, Yufu Qiu, Junyan Yan, Wenhui Zeng, Wenlong Lu +1 more
similarity 0.52
Abstract

Shape and force sensing have long been critical bottlenecks in the development of compact capstan-driven continuum surgical robots, primarily due to the difficulty of obtaining cable tension information within the confined capstan assembly. To overcome these challenges, this paper presents an integrated design-modeling-sensing approach based on the concept of actuation-perception co-design. A compliant element is introduced into the motor mounting bracket of the drive system, enabling micro-deformation under the cable reaction force and thereby allowing real-time cable tension measurement without occupying the compact capstan space. To address the modeling complexity arising from unconventional joint configurations introduced by the spatial cable routing strategy, a parallel computation framework based on a multibody short-thick-beam model is proposed, which captures shear effects in short beam segments and synergistic multi-cable interactions while achieving real-time performance. Building on this framework, stable shape and force sensing is achieved by incorporating a proximal multi-axis force/torque sensor as an additional measurement anchor. Following this design-modeling-sensing framework, capstan-driven continuum surgical robots with single- and dual-segment configurations are developed. Experimental results validate the proposed framework in both single- and dual-segment continuum robots, demonstrating real-time tip pose estimation together with contact force and location perception. By enabling cable tension feedback without compromising the compact capstan architecture, the proposed framework makes integrated perception feasible for capstan-driven continuum surgical robots.

0.04

MagPillar: A Soft Magnetopillar Array Tactile Sensor for Robotic Surface Perception

cs.RO ·2026-11-01 ·Haotian Guo, Yu Feng, Hao Wu, Jiazhi Tang, Ningbin Zhang +1 more
similarity 0.52
Abstract

Robotic surface exploration benefits from tactile interfaces that accommodate contact and capture variations in surface characteristics. Herein, we report MagPillar, a tactile sensor inspired by spider tactile hairs that combines a magnetic pillar array with three-axis Hall sensing. A full-array mechanical and magnetic-field model characterizes how pillar deformation affects the superposed fields measured across the array, providing a physical basis for interpreting its contact responses. The compliant pillar architecture translates contact with surface textures and geometric features into distinct magnetic response patterns. Then, in robotic surface perception experiments, spectral features and logistic regression distinguish six material surfaces with an offline accuracy of 99.34% under within-session temporally blocked cross-validation. Continuous scans over periodic protrusions produce amplitude and peak-spacing variations consistent with changes in surface geometry. These findings connect compliant contact mechanics with distributed magnetic sensing, paving a new path for material recognition and qualitative surface-profile perception.

0.35