CS Paper Radar

Real-Time Transient Response Optimization

Anahida Kanade, Djan Tanova, Steve Conner, Taner Dosluoglu

eess.SY ·submitted 2026-08-22 09:56 UTC · v1
published

Abstract

Use of artificial intelligence in motor control applications that can be deployed within the microcontrollers need to comply with real-time demands of motor control systems. A supplementary controller approach that can be integrated within existing microcontrollers is presented. The proposed approach is implemented on a weeteq motor control integrated circuit and tested in the lab. A complete unsupervised motor control deployment solution was developed, and the real-time system response correction demonstrated under dynamic loads measured with and without the supplementary controller. The solution provides 100% coverage of real-time data at control loop sample rate and model inference period between 100usec and 1msec. The importance of latency for reduction of dynamic regulation margin during transient response is demonstrated with up to 68% reduction of the system response error. A novel key performance indicator based on principal components transform is introduced that provides a quantitative figure of merit for improvement of the transient response, in terms of the dynamic regulation margin, stability considerations and iterative improvements of consecutive regression model outputs. The significant events related to dynamic changes in the equipment and external operating conditions are detected at milliseconds resolution and recorded as highly compressed vectors representing deviation of the system response from linear steady state conditions. The resolution in time and accuracy of this vector data will enable a new level of system level optimisation that has not been possible using the time series data from IoT sensors in current equipment health monitoring solutions.

Comment
6 pages, 9 figures, 1 table. Technical correspondence of original research and data that has not yet been accepted for publication in any journal

Closest papers

Nearest neighbours by meaning across the whole index.

Model-Free Current Control of Permanent Magnet Synchronous Motors via ESO-Based Disturbance Feedforward and Data-Driven H-infinity Residual Feedback

eess.SY ·2026-09-22 ·YongBo Li, Shuang Liang, HongWei Ma
similarity 0.53
Abstract · 20 pages, 14 figures

This paper proposes a model-free current control method for permanent magnet synchronous motors (PMSMs) based on disturbance feedforward and residual feedback. An ultra-local current model incorporates motor dynamics, parameter uncertainties, cross-coupling effects, and other nonideal factors into generalized lumped disturbances. An extended state observer (ESO) estimates these lumped disturbances and compensates for them through feedforward action, transforming the original PMSM current-control problem into regulation of a simplified post-compensation residual system. A state-feedback H-infinity controller for the residual system is then learned directly from operating data using off-policy integral reinforcement learning. Owing to the simplified residual dynamics, the value function and control policies are parameterized in quadratic and linear forms, reducing the learning problem to low-dimensional parameter estimation without neural-network approximation. The proposed method requires neither prior knowledge nor online identification of PMSM electrical parameters: input-gain mismatch is incorporated into the ESO-estimated lumped dynamics, while the residual-feedback policy is obtained from operating data. Comparative simulations against deadbeat predictive current control, model-based H-infinity control, and model-free predictive current control show fast current tracking, low current distortion, and strong robustness to large parameter variations. With the learned H-infinity policy fixed and without retraining or retuning, nearly unchanged control performance is maintained when stator resistance, stator inductance, and permanent-magnet flux linkage are simultaneously varied to 20% and 200% of their nominal values.

0.29

Adaptive Model Predictive Control for Damping IBR-Induced SSOs

eess.SY ·2026-11-11 ·Fiaz Hossain, Nilanjan Ray Chaudhuri, Constantino M. Lagoa
similarity 0.51
Abstract

We propose an adaptive model predictive control (MPC) approach to damp sub-synchronous oscillations (SSOs) induced by grid-following (GFL) inverter-based resources (IBRs). Unlike traditional model predictive controller designed considering the nominal plant that may not perform well in other conditions, we use plants that alter with changing operating point. To capture the plant dynamics, we use recursive least squares (RLS) based system identification with variable forgetting factor. This approach allows us to discount past data and avoid bias caused by large transient outliers while performing system identification. We present a proof of the convergence of the model parameters in the presence of finite outliers. We propose to update the model inside the MPC optimization problem periodically after a predetermined time interval instead of each sampling instant since the operating point changes slowly in a practical power system. The MPC design allows us to directly impose constraints on control inputs so that the IBR current limits are respected. Our approach also addresses the issue of unavailability of IBR models. We show the accuracy of the system identification and the superior performance of the proposed controller on the modified IEEE $4$-machine system and the modified IEEE $68$-bus system as compared with the traditional MPC.

0.29

Physics-Guided Inferencer-in-the-Loop Digital-Twin for Real-Time Adaptive Emulation of Nonlinear PMSMs

eess.SY ·2026-10-28 ·Songyang Zhang, Yuzhong Zhang, Venkata Dinavahi
similarity 0.51
Abstract

A real-time digital-twin (RTDT) of a permanent magnet synchronous machine (PMSM) allows drive controllers to be tested in hardware-in-the-loop (HIL) before they meet the real machine. Its machine model rests on identified parameters or flux look-up tables (LUTs) from finite-element analysis (FEA) or characterization tests; the maps are regenerated offline when the machine changes, and online estimators track a few parameters such as resistance and PM flux. This article makes the executed model learnable from reference data. A physics-guided machine learning (PGML) network advances the currents and predicts torque in one step, trained with analytical one-step labels. In the proposed Inferencer-in-the-Loop (IIL) architecture, a GPU retrains the network while a field-programmable gate array (FPGA) executes the last accepted weights. For damper circuits, shifted parameters, and an FEA-calibrated saturated machine, one kernel form reaches average normalized mean absolute errors (NMAEs) of 0.19%-0.67% at measured FPGA kernel latencies of 0.30-0.34 $μ$s, and retraining for a shifted machine nears its final loss within 94 s. On a magnetically linear 200-W drive, a residual form corrects the analytical step and learns its physical parameters from operating data; each step takes under 2.5 $μ$s, 20 times faster than real time and ahead of the physical drive's measurements even at 20-kHz sampling. On six held-out runs (1193 s), its $i_q$ error is 5.9%-9.4% of measured RMS, against 10.4%-13.2% for an independently fitted grey-box model, and over 30 min of loaded heating its online-updated heads track a 4.1% winding-resistance rise with an RMS error of 0.44 m$Ω$.

0.29

From Continuous Design to Delay-Aware Discrete Synthesis: Guaranteed High-Bandwidth Joint Control for PMSM Drives

cs.RO ·2026-08-14 ·Edmundo Pozo Fortunić, Mehmet C. Yildirim, Sami Haddadin
similarity 0.51
Abstract · 9 pages, 3 figures

The increasing dynamic demands of modern robotic joints require current controllers to achieve high bandwidth over wide operating ranges of speed, acceleration, and torque, where communication, computation, and discrete-time effects can no longer be neglected. Conventional PMSM current controllers are typically designed in continuous time and subsequently discretized, leaving the sampling frequency and the impact of implementation delays largely to heuristic selection and iterative validation. This paper introduces a task-aware, delay-extended discrete-time joint model that explicitly accounts for physical communication and computation delays and enables direct synthesis of a discrete PI current controller with prescribed bandwidth and delay guarantees throughout the operating envelope. The framework analytically determines the minimum required sampling frequency, controller gains, and DC-link voltage needed to satisfy the specified motor and joint performance. Simulations across a range of dynamic requirements validate the methodology and demonstrate substantially reduced sampling-frequency and DC-link-voltage requirements compared with conventional continuous-time-based design. Experiments on a newly developed custom robotic joint further validate the proposed framework under real embedded implementation conditions.

0.10

Stability-Constrained Imitation Learning for Performance-Guaranteed Neural Feedback Frequency Control in Microgrids

eess.SY ·2026-11-17 ·Sajid Kamal, Yichen Zhang, Feng Qiu, Tianqiao Zhao
similarity 0.51
Abstract · 10 pages

Guaranteeing performance for frequency control is challenging within traditional control paradigms, as it demands precise disturbance estimation and real-time control signal computation within a timeframe of seconds. This paper addresses this challenge by proposing a stability-certified imitation learning framework for frequency regulation in low-inertia microgrids. Based on the frequency response model of the microgrid, an offline numerical optimal control is employed to generate near-optimal pairs of state and control dataset, which are subsequently used to train a deep neural network (DNN) feedback controller. To ensure the closed-loop stability, the DNN controller is trained with a set of Lyapunov-based stability constraints derived using absolute stability theory. Such an imitation learning paradigm can significantly improve the training efficiency, while the resulting DNN controller acts as an end-to-end function that simultaneously handles disturbance estimation and control optimization. The proposed framework is validated on a modified IEEE 33-node diesel-wind microgrid. The DNN controllers are deployed in wind turbine generators (WTGs) to provide decentralized, intelligent supplementary active power support to always maintain frequency deviations within predefined safety bounds under different disturbances while preserving closed-loop stability.

0.34

Micro Neural Policies for Safe Real-Time Robotic Control

cs.RO cs.AI ·2026-10-06 ·Hongpeng Cao, Riccardo Curcio, Daniele Ottaviano, Marco Caccamo
similarity 0.48
Abstract · 9 pages

In this paper, we investigate the synthesis of Micro Neural Policies (MNP) to enable safe and robust real-time robotic control on computationally constrained embedded devices. We demonstrate that integrating Evolution Strategy (ES) and Statistical Model Checking (SMC)-based verification for policy search can drastically reduce neural network size without compromising safety and robustness. We conduct a large-scale training and evaluation of MNP on Cartpole and Quadrotor control tasks, varying control frequencies and network architectures. After validating these policies in simulation, we evaluate their deployability through zero-shot transfer to physical systems. Our experiments show that MNP can successfully achieve safe sim-to-real transfer without sacrificing control performance. We then show that the policies' memory footprint, ranging from 0.5 to 7.5 kB, allows deployment on microcontrollers, where they achieve real-time inference latency with under 25 ns of jitter while leaving the chip idle for over 97% of the time for additional workloads. This makes them a highly practical solution for severely resource-constrained robotic systems.

0.21

Fast-varying Natural Frequencies and Damping Ratio Identification for Linear Time-Varying System

cs.LG ·2026-09-17 ·Melisa Bozaci, Alice Cicirello
unusual similarity 0.48
Abstract · Preprint submitted to Mechanical Systems and Signal Processing

This work proposes a physics-enhanced machine learning approach for the system identification of Linear Time-Varying (LTV) systems under time-varying operating conditions in terms of fast-varying natural frequencies and damping ratios by combining a long short-term memory network with an Extended Kalman Filter (EKF). The proposed approach uses vibration data (displacement and velocity measurements), domain knowledge of modal damping ratios, and a physics-based model that can yield an approximate natural frequencies time-dependency model. The approach is validated using synthetic data generated from a finite element model of a 2-blade offshore wind turbine under realistic environmental and operating conditions. This system displays fast time-varying frequencies due to operating conditions, whose identification is particularly challenging because of the wind and wave loading. The robustness of the proposed approach is assessed under assumed incorrect system information (e.g. damping ratio). The proposed approach is evaluated across different environmental and operating conditions to show its applicability to different operating regimes. The results show the approach can accurately identify the selected fast-varying natural frequency, 1st Fore-Aft (FA-1) mode, with a maximum root mean square error of 0.0012 Hz. The results demonstrate that the model trained on EKF estimates depends on accurate damping values, whereas the model trained on physics-based data exhibits robustness to incorrect damping assumptions. The approach is extended to damping ratio identification for the selected mode by estimating the root mean square error between models trained on EKF estimates and physics-based data. The results show that the approach can yield a good approximation of the FA-1 mode damping ratio using grid search, offering an improvement over covariance-driven stochastic subspace identification.

0.30

Interpreting Control Latents for System Identification via Conditional Flow Matching

cs.RO ·2026-08-24 ·Dingqi Zhang, Ruiqi Zhang, Mark W. Mueller
similarity 0.47
Abstract

Latent-conditioned adaptive policies can control robots across changing dynamics, but their learned latents remain internal representations of the policy rather than physical models that can be inspected, rolled out, or used by other control modules. This limits closed-loop analysis, diagnosis, and further improvement of a fixed policy. A direct mapping from latent to physical parameters is also under-specified, because multiple systems can induce similar closed-loop behavior. We therefore decode each operational latent into a distribution of quadrotor models using conditional flow matching. The decoded distribution enables two downstream uses without modifying the policy: online predictive tuning of a high-level controller around the fixed low-level policy, and robustness analysis under specified disturbances. Under perturbed actuator dynamics, decoded-model predictive tuning reduces position tracking RMSE by $23\%$ and heading RMSE by $45\%$ relative to fixed gains. Under Gaussian force disturbances, decoded-model ensembles closely predict the lateral tracking-error evolution. Together, these results show that control latents can be converted into physical model ensembles for tuning, robustness analysis, and diagnosis of frozen adaptive policies.

0.30