CS Paper Radar

From Continuous Design to Delay-Aware Discrete Synthesis: Guaranteed High-Bandwidth Joint Control for PMSM Drives

Edmundo Pozo Fortunić, Mehmet C. Yildirim, Sami Haddadin

cs.RO ·submitted 2026-08-14 23:27 UTC · v1

Abstract

The increasing dynamic demands of modern robotic joints require current controllers to achieve high bandwidth over wide operating ranges of speed, acceleration, and torque, where communication, computation, and discrete-time effects can no longer be neglected. Conventional PMSM current controllers are typically designed in continuous time and subsequently discretized, leaving the sampling frequency and the impact of implementation delays largely to heuristic selection and iterative validation. This paper introduces a task-aware, delay-extended discrete-time joint model that explicitly accounts for physical communication and computation delays and enables direct synthesis of a discrete PI current controller with prescribed bandwidth and delay guarantees throughout the operating envelope. The framework analytically determines the minimum required sampling frequency, controller gains, and DC-link voltage needed to satisfy the specified motor and joint performance. Simulations across a range of dynamic requirements validate the methodology and demonstrate substantially reduced sampling-frequency and DC-link-voltage requirements compared with conventional continuous-time-based design. Experiments on a newly developed custom robotic joint further validate the proposed framework under real embedded implementation conditions.

Comment
9 pages, 3 figures

Closest papers

Nearest neighbours by meaning across the whole index.

CLIS-MPPI: Closed-Loop Model Predictive Path Integral Control With Initial-State Sampling Under Execution Delay

cs.RO ·2026-10-15 ·Zidong Liu, Xu Chen
similarity 0.55
Abstract · 65th IEEE Conference on Decision and Control (CDC 2026)

Sampling-based motion planning such as Model Predictive Path Integral (MPPI) control has become attractive for robotics due to its ability to handle nonlinear dynamics and non-smooth objectives without gradient information, while leveraging parallel rollout computation for real-time performance. However, in real-world robotic systems, the optimized control input is often applied after a non-negligible planning delay, causing a mismatch between the state used in forward simulation and the actual state at control execution, which can significantly degrade planning accuracy and may even lead to unsafe behavior such as collisions. This paper proposes Closed-Loop MPPI with Initial-State Sampling (CLIS-MPPI), which explicitly addresses execution-time state mismatch by modeling planning delay as a distribution over plausible execution-time initial states, performing rollout optimization from sampled initial states, and applying a rollout-based local feedback correction during control execution. The proposed method is validated through real-world experiments on a 6-DoF UR5e manipulator in a narrow-passage task involving obstacle avoidance and end-effector target reaching. Across 5 real-world runs of the same task, standard MPPI collided in 2 runs, whereas CLIS-MPPI remained collision-free in all 5 runs. Averaged over all collision-free runs for each method (3 for MPPI and 5 for CLIS-MPPI), CLIS-MPPI reduced the average task completion time from 25.4s to 24.4s and the average end-effector path length from 0.456 m to 0.425 m. It also reduced the overall joint-position and joint-velocity root mean square errors (RMSEs) from 0.100 rad and 0.108 rad/s to 0.017 rad and 0.011 rad/s, respectively. These results demonstrate improved safety, planning-execution consistency, and motion smoothness.

0.11

Task-Oriented Co-Design and Optimization of Geared Actuators for Robotic Applications

cs.RO ·2026-09-19 ·Xuanyu Huang, Jianqiang Dong, Hang Zhao
hot direction similarity 0.53
Abstract

Different tasks performed by legged robots impose distinct torque and speed requirements on actuators. Existing robotic actuators are generally optimized at the component level for metrics such as torque or power density, without explicit task guidance. System-level optimization across components such as motors, gearboxes, and sensors is challenging because of the high computational cost and coupling among mechanical, electrical, and electromagnetic behaviors. Consequently, improvements in individual components may not translate into better robot performance in a specific task. To this end, we present a systematic optimization framework for task-oriented co-design of actuator hardware and control. First, surrogate models are employed to accelerate motor evaluation and support global exploration of the coupled design space. Then, a hierarchical mixed-variable optimization strategy is adopted, combining discrete enumeration with continuous search over dimensions and real-valued indices. These indices are rounded to select admissible values for the remaining discrete choices before each evaluation. Within this search, rated output torque density and task performance are jointly optimized, with Bezier-parameterized joint torque profiles determined for each hardware candidate. Finally, the effectiveness of the proposed framework is validated through actuator fabrication and experiments on a two-degree-of-freedom jumping leg. Based on its measured mass, the fabricated prototype achieves a nominal rated output torque density of 35.7 N m/kg, approximately 60% higher than that of a widely used commercial geared joint actuator, while being 18.6% lighter. Under matched bench conditions, it achieves 12.0% greater jump height at twice-rated torque. Together, these results demonstrate a systematic route from task requirements to actuator design and control.

0.36

Real-Time Transient Response Optimization

eess.SY ·2026-08-22 ·Anahida Kanade, Djan Tanova, Steve Conner, Taner Dosluoglu
published similarity 0.51
Abstract · 6 pages, 9 figures, 1 table. Technical correspondence of original research and data that has not yet been accepted for publication in any jo…

Use of artificial intelligence in motor control applications that can be deployed within the microcontrollers need to comply with real-time demands of motor control systems. A supplementary controller approach that can be integrated within existing microcontrollers is presented. The proposed approach is implemented on a weeteq motor control integrated circuit and tested in the lab. A complete unsupervised motor control deployment solution was developed, and the real-time system response correction demonstrated under dynamic loads measured with and without the supplementary controller. The solution provides 100% coverage of real-time data at control loop sample rate and model inference period between 100usec and 1msec. The importance of latency for reduction of dynamic regulation margin during transient response is demonstrated with up to 68% reduction of the system response error. A novel key performance indicator based on principal components transform is introduced that provides a quantitative figure of merit for improvement of the transient response, in terms of the dynamic regulation margin, stability considerations and iterative improvements of consecutive regression model outputs. The significant events related to dynamic changes in the equipment and external operating conditions are detected at milliseconds resolution and recorded as highly compressed vectors representing deviation of the system response from linear steady state conditions. The resolution in time and accuracy of this vector data will enable a new level of system level optimisation that has not been possible using the time series data from IoT sensors in current equipment health monitoring solutions.

0.36

Model-Free Current Control of Permanent Magnet Synchronous Motors via ESO-Based Disturbance Feedforward and Data-Driven H-infinity Residual Feedback

eess.SY ·2026-09-22 ·YongBo Li, Shuang Liang, HongWei Ma
similarity 0.50
Abstract · 20 pages, 14 figures

This paper proposes a model-free current control method for permanent magnet synchronous motors (PMSMs) based on disturbance feedforward and residual feedback. An ultra-local current model incorporates motor dynamics, parameter uncertainties, cross-coupling effects, and other nonideal factors into generalized lumped disturbances. An extended state observer (ESO) estimates these lumped disturbances and compensates for them through feedforward action, transforming the original PMSM current-control problem into regulation of a simplified post-compensation residual system. A state-feedback H-infinity controller for the residual system is then learned directly from operating data using off-policy integral reinforcement learning. Owing to the simplified residual dynamics, the value function and control policies are parameterized in quadratic and linear forms, reducing the learning problem to low-dimensional parameter estimation without neural-network approximation. The proposed method requires neither prior knowledge nor online identification of PMSM electrical parameters: input-gain mismatch is incorporated into the ESO-estimated lumped dynamics, while the residual-feedback policy is obtained from operating data. Comparative simulations against deadbeat predictive current control, model-based H-infinity control, and model-free predictive current control show fast current tracking, low current distortion, and strong robustness to large parameter variations. With the learned H-infinity policy fixed and without retraining or retuning, nearly unchanged control performance is maintained when stator resistance, stator inductance, and permanent-magnet flux linkage are simultaneously varied to 20% and 200% of their nominal values.

0.29

LunaDrive: A Delay-Compensated High-Voltage GaN FET-Based Motor Driver for Dynamic Robots with Flat BLDC Motors

cs.RO ·2026-09-18 ·Sota Yuzaki, Temma Suzuki, Hiromi Tada, Masanori Konishi, Kento Kawaharazuka +1 more
publishedunusual similarity 0.49
Abstract · Accepted at IROS2026, website - https://woodrobo.github.io/lunadrive/ , YouTube - https://youtu.be/iD8vzvis_5w

The performance improvement of high-power flat BLDC motors has accelerated the development of dynamic robots. However, many commercially available servo motors assume operating voltages of 48 V or lower, which limits the maximum rotational speed. Dynamic robots require rapid energy generation, so this voltage constraint restricts motion performance. Therefore, driving motors beyond the rated voltage is desirable to increase the instantaneous maximum speed. On the other hand, semiconductor devices used in motor drivers have a trade-off between voltage rating and current capacity. Conventional drivers using Si MOSFETs have difficulty achieving both high-voltage and high-current operation. Although GaN FETs are promising, compact drivers that can be mounted on the rear side of flat BLDC motors remain limited. In this study, a motor driver for high-power flat BLDC motors using GaN FETs is developed. The effect of delay compensation in the high-speed region beyond the rated operating range is also investigated. In the experiments, under 96 V operation, a continuous current of 30 A was achieved with a heat sink attached. A peak current of 80 A and a maximum electrical frequency of 3110 Hz were confirmed. A high-speed load lifting experiment driven by a LiPo battery 24S (100 V) was also conducted, demonstrating applicability to dynamic robot operation.

0.45

Structure-Actuation Co-Design of All-Electric Heavy-Duty Robotic Manipulators

cs.RO eess.SY ·2026-10-27 ·Mohammad Bahari, Amir Hossein Barjini, Jouni Mattila
benchmark similarity 0.49
Abstract · 6 pages manuscript submitted to a conference (ICCMA 2026)

This paper presents a mixed discrete-continuous multiobjective bilevel framework for the structure-actuation co-design of all-electric heavy-duty robotic manipulators. The upper level optimizes manipulator geometry and actuation topology, while joint-specific lower-level searches construct feasible archives of discrete motor, gearbox, and screw configurations. A system-level coordinator selects actuator packages according to hardware mass, co-design cost, and loss-aware supply energy, and the resulting actuator masses are fed back to the robot model until a mass-consistent fixed point is obtained. Evaluation on a full-pose SE(3) benchmark with a 100-kg tool payload yields eight feasible nondominated designs, all satisfying the 12 prescribed poses. Actuator-mass coupling converges in three iterations for every reported design. A fixed-design ablation shows that one-pass sequential sizing changes hardware mass by up to 2.13%, co-design cost by 10.20%, and supply energy by 9.40% in magnitude. Payload screening further reveals increasing mass-cost-energy demand and changes in competitive mechanism topology with carried load.

0.45

Real-Time Dynamics-Based Torque-Sampling MPPI for Compliant and Force Aware Manipulation

cs.RO ·2026-09-02 ·Euncheol Im, Taehyun Kim, Yonghwan Oh, Myotaeg Lim, Yisoo Lee
published similarity 0.48
Abstract · 8 pages, 6 figures. Accepted to the IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS 2026)

This study proposes a novel Model Predictive Path Integral (MPPI)-based task-space control framework. The proposed framework explicitly solves rigid-body dynamics within a real-time MPC formulation and enforces safety constraints, enabling accurate motion and force control that yields compliant behaviors for safe and effective physical interaction of robotic manipulators in unstructured environments. By leveraging MPPI, the proposed framework efficiently handles nonlinear dynamics that are difficult to solve with conventional MPC approaches in real-time. Furthermore, we develop a torque-sampling-based control architecture that enables efficient exploitation of GPU-based parallelization, resulting in effective compliant and force-aware behaviors. As a result, the proposed framework achieves a solver update rate of over 166 Hz with a 0.18 s prediction horizon, and its performance is validated through real-world experiments on a 7-DoF manipulator.

0.38

From Asymptotic to Designer-Assigned-Time Control: A Review of Stability Notions, Design Mechanisms, and Controller Architectures

eess.SY ·2026-10-08 ·Özhan Bingöl
surveybenchmark similarity 0.48
Abstract

Many control tasks require a target to be reached not only eventually but on time. Finite-, fixed-, predefined-, and prescribed-time control address this need, yet the labels are used loosely: a settling time that grows with the initial condition, a bound that holds for all initial conditions, a deadline chosen by the designer, and a limit attained only at the terminal instant often share one name. This review aims to make such claims comparable. It separates three questions that are often conflated: what temporal property is promised, which feature of the Lyapunov analysis produces it, and which controller architecture carries it into the closed loop. A recurring question is whether a guarantee proven for an idealized loop survives once observers, adaptation, disturbances, actuator limits, and digital implementation are included. The examined studies are therefore audited one by one, recording what each claims, which variable is actually certified, and how the result is validated. The audit shows that estimation and approximation errors often reduce an exact guarantee to a practical one, and that experimental evidence comes mostly from fast electromechanical systems. A scalar benchmark with two complementary tunings shows how much of the apparent difference between methods stems from conservative bounds, initial-condition dependence, and numerical tolerance, and how saturation and sampling can delay or remove a deadline. The review closes with open problems, among them deciding which deadlines a given plant can meet, combining certificates across interconnected subsystems, and preserving a guarantee through implementation.

0.18