CS Paper Radar

LunaDrive: A Delay-Compensated High-Voltage GaN FET-Based Motor Driver for Dynamic Robots with Flat BLDC Motors

Sota Yuzaki, Temma Suzuki, Hiromi Tada, Masanori Konishi, Kento Kawaharazuka, Kei Okada

cs.RO ·submitted 2026-09-18 14:23 UTC · v1
publishedunusual

Abstract

The performance improvement of high-power flat BLDC motors has accelerated the development of dynamic robots. However, many commercially available servo motors assume operating voltages of 48 V or lower, which limits the maximum rotational speed. Dynamic robots require rapid energy generation, so this voltage constraint restricts motion performance. Therefore, driving motors beyond the rated voltage is desirable to increase the instantaneous maximum speed. On the other hand, semiconductor devices used in motor drivers have a trade-off between voltage rating and current capacity. Conventional drivers using Si MOSFETs have difficulty achieving both high-voltage and high-current operation. Although GaN FETs are promising, compact drivers that can be mounted on the rear side of flat BLDC motors remain limited. In this study, a motor driver for high-power flat BLDC motors using GaN FETs is developed. The effect of delay compensation in the high-speed region beyond the rated operating range is also investigated. In the experiments, under 96 V operation, a continuous current of 30 A was achieved with a heat sink attached. A peak current of 80 A and a maximum electrical frequency of 3110 Hz were confirmed. A high-speed load lifting experiment driven by a LiPo battery 24S (100 V) was also conducted, demonstrating applicability to dynamic robot operation.

Comment
Accepted at IROS2026, website - https://woodrobo.github.io/lunadrive/ , YouTube - https://youtu.be/iD8vzvis_5w

Closest papers

Nearest neighbours by meaning across the whole index.

Environmental Assessment of GaN Current-Source and Voltage-Source AC-AC Variable Speed Drives

eess.SY ·2026-11-09 ·Luc Imperiali, Jonas Huber
similarity 0.50
Abstract · Submitted to an IEEE journal

Three-phase ac-ac converters for variable-speed drives can be realized conventionally as voltage-source converters (VSCs) or, leveraging emerging monolithic bidirectional GaN power transistors (M-BDSs), as current-source converters (CSCs). This paper presents a comparative life-cycle assessment of a realized VSC and a CSC demonstrators including grid-side and motor-side EMI filters, and with identical specifications (1.4 kW rated power, 200 V line-to-line rms grid and motor voltage). The embodied carbon footprints are similar (44.8 kgCO2eq for the VSC and 47.4 kgCO2eq for the CSC) and dominated by auxiliary and control electronics, and the printed circuit boards. Over 10 years of continuous operation under the NEMA Power Index mission profile for variable-load centrifugal systems (pumps, fans), the CSC's higher part-load efficiency translates into a clearly lower life-cycle carbon footprint of around 900 kgCO2eq compared to the VSC's 1130 kgCO2eq when operating with a carbon-intense electricity mix (440 gCO2eq/kWh). However, this difference almost vanishes when considering a future renewable electricity mix (25 gCO2eq/kWh).

0.24

From Continuous Design to Delay-Aware Discrete Synthesis: Guaranteed High-Bandwidth Joint Control for PMSM Drives

cs.RO ·2026-08-14 ·Edmundo Pozo Fortunić, Mehmet C. Yildirim, Sami Haddadin
similarity 0.49
Abstract · 9 pages, 3 figures

The increasing dynamic demands of modern robotic joints require current controllers to achieve high bandwidth over wide operating ranges of speed, acceleration, and torque, where communication, computation, and discrete-time effects can no longer be neglected. Conventional PMSM current controllers are typically designed in continuous time and subsequently discretized, leaving the sampling frequency and the impact of implementation delays largely to heuristic selection and iterative validation. This paper introduces a task-aware, delay-extended discrete-time joint model that explicitly accounts for physical communication and computation delays and enables direct synthesis of a discrete PI current controller with prescribed bandwidth and delay guarantees throughout the operating envelope. The framework analytically determines the minimum required sampling frequency, controller gains, and DC-link voltage needed to satisfy the specified motor and joint performance. Simulations across a range of dynamic requirements validate the methodology and demonstrate substantially reduced sampling-frequency and DC-link-voltage requirements compared with conventional continuous-time-based design. Experiments on a newly developed custom robotic joint further validate the proposed framework under real embedded implementation conditions.

0.10

Modularity is Not Enough: Demonstration of a Solderless 400 V DC, 2.5 kW Three-Phase Inverter

eess.SY ·2026-09-23 ·Luc Imperiali, Aaron Griesser, Jonas Huber
unusual similarity 0.44
Abstract · Submitted to an IEEE journal

This paper presents the design and experimental evaluation of a fully solderless realization of a 400 V, 2.5 kW GaN-based variable speed drive (VSD), using screw-clamped resin molds and rubber compression pads instead of soldered interconnections. The power stage uses 650 V GaN power transistors and is operated at a switching frequency of 200 kHz. The solderless demonstrator is compared to a soldered reference realization using an identical printed circuit board (PCB). Over 120 thermal cycles with heatsink temperatures up to 90 °C, the solderless contacts show no degradation in effective on-state resistances (including contact resistances). Separately, open-loop vibration sweeps from 5 Hz to 2 kHz with acceleration amplitudes above 10 g were performed on the solderless assembly and left the continuously powered demonstrator electrically intact; subsequent resistance and nominal-power checks likewise indicate no contact degradation. An initial life-cycle assessment (LCA) indicated a higher embodied carbon footprint for the solderless realization due to 3D-printed resin molds, whereas a prospectively evaluated injection-molding scenario reduces the carbon footprint to near that of the soldered reference. The solderless assembly furthermore enables non-destructive component replacement, as demonstrated after a power transistor failure, as well as component re-use. These results support the feasibility of repair-oriented, industrially relevant kilowatt-class solderless power converters.

0.26

Real-Time Transient Response Optimization

eess.SY ·2026-08-22 ·Anahida Kanade, Djan Tanova, Steve Conner, Taner Dosluoglu
published similarity 0.40
Abstract · 6 pages, 9 figures, 1 table. Technical correspondence of original research and data that has not yet been accepted for publication in any jo…

Use of artificial intelligence in motor control applications that can be deployed within the microcontrollers need to comply with real-time demands of motor control systems. A supplementary controller approach that can be integrated within existing microcontrollers is presented. The proposed approach is implemented on a weeteq motor control integrated circuit and tested in the lab. A complete unsupervised motor control deployment solution was developed, and the real-time system response correction demonstrated under dynamic loads measured with and without the supplementary controller. The solution provides 100% coverage of real-time data at control loop sample rate and model inference period between 100usec and 1msec. The importance of latency for reduction of dynamic regulation margin during transient response is demonstrated with up to 68% reduction of the system response error. A novel key performance indicator based on principal components transform is introduced that provides a quantitative figure of merit for improvement of the transient response, in terms of the dynamic regulation margin, stability considerations and iterative improvements of consecutive regression model outputs. The significant events related to dynamic changes in the equipment and external operating conditions are detected at milliseconds resolution and recorded as highly compressed vectors representing deviation of the system response from linear steady state conditions. The resolution in time and accuracy of this vector data will enable a new level of system level optimisation that has not been possible using the time series data from IoT sensors in current equipment health monitoring solutions.

0.36

Electric Racing Kart with BLDC Drive, LiFePO4 Battery System, Traction Control and Regenerative Braking

eess.SY ·2026-10-06 ·Johannes Stockhammer, Tom Rettenwander, Philipp Huber
publishedunusual similarity 0.39
Abstract · German title: Elektro-Rennkart mit BLDC-Antrieb, LiFePO4-Batteriesystem, Antischlupfregelung und Rekuperation. Diploma thesis, HTL Braunau, …

This diploma thesis documents the conversion of a petrol-powered go-kart into a battery-electric kart with a 10 kW BLDC drive, a LiFePO$_4$ traction battery with battery management system, a slip-based traction control and regenerative braking. The traction control estimates the slip of the driven rear axle from three Hall-effect wheel-speed sensors as $λ= (v_R - v_F)/v_R$ and reduces the torque command of the throttle pedal when the axle slips. It runs on a 32-bit ARM Cortex-M3 microcontroller (SAM3X8E) in the signal path between pedal and motor controller, with galvanic isolation and an emergency stop. Regenerative braking uses the generator mode of the motor controller in three stages: motor brake on throttle release, light braking via a steering-wheel button, and blended braking with the hydraulic brake. Drivetrain calculations show that the kart is traction-limited. At rated torque, the drive force at standstill exceeds the transmissible traction force by a factor of 1.7 to 2.0, up to approx. 27 to 43 km/h. Traction control is therefore a functional requirement of the drivetrain. The calculated top speed is approx. 65 km/h. Regenerative braking reaches approx. 0.45 g and could cover up to about 30 % of the energy demand on a winding track. With 80 % of the nominal battery energy, approx. 44 min of driving at 50 % motor load result, so the target of one hour is missed. The initial charging measurement quantifies the flat LiFePO$_4$ voltage plateau at 0.7 to 1.8 mV per percent state of charge, which makes voltage-based state-of-charge estimation unreliable. Cold cells showed a voltage sag under load that triggered the low-voltage alarm. Validation of the control functions by instrumented driving tests is the main open point.

0.38

High-Performance Sensorless Control for High-Speed PMSM with Current Source Inverters

eess.SY ·2026-09-22 ·Nail Tosun, Devinda Molligoda, Xu Deng, Barrie Mecrow
publishedunusual similarity 0.38
Abstract · Accepted, and presented at ICEM 2026

Current source inverters (CSIs) are emerging as competitive alternatives to voltage source inverters (VSIs) for high-speed motor drives because they inherently suppress harmonic currents, offer output-voltage boosting, and reduce motor-side electromagnetic interference. Sensorless control of CSI-fed permanent magnet synchronous machines (PMSMs) remains less mature than VSI counterparts, primarily because conventional implementations require measurement of all circuit state variables. This paper proposes a weak-resonance-based approximation that reconstructs stator currents from inverter modulation commands and feedforward capacitor-current estimation, thereby reducing the sensing requirement to the dc-link current and two terminal voltages. The proposed observer--PLL structure is analysed for computational complexity and validated through simulations and experiments on a 100~W, 100~krpm GaN-based two-stage CSI prototype (buck + CSI). Quantitative results demonstrate accurate rotor-position tracking and high-bandwidth operation while maintaining the reduced sensor set. Proposed method performs well in simulation and experiment, achieving a position estimation error below $5^\circ$ at 100~krpm.

0.40

QDD-MM: A Simple and Compact Open-Source Muscle Module with Quasi-Direct-Drive Motor for Tendon-driven Robots

cs.RO ·2026-11-18 ·Kento Kawaharazuka, Yoshimoto Ribayashi, Takahiro Hattori, Shunnosuke Yoshimura, Kei Okada
publishedcode/data similarity 0.35
Abstract · Accepted to IEEE-RAS Humanoids 2026, website - https://haraduka.github.io/qddmm/, youtube - https://www.youtube.com/watch?v=09xRhZO497k

Tendon-driven robots, which actuate like biological muscles by using motors to wind wires, offer advantages such as variable stiffness and redundant actuation. Despite these advantages, musculoskeletal structures inherently involve a large number of diverse muscles, making it desirable to compactly modularize each muscle unit and flexibly accommodate diverse muscle arrangements. While various small muscle modules have been proposed to date, existing designs tend to be complex, difficult to maintain, and suffer from low backdrivability and limited actuation speed due to their high gear ratios. In this work, we propose QDD-MM, a muscle module that leverages recent advances in quasi-direct-drive motors to achieve a simpler and more compact structure with higher backdrivability and faster actuation than previous modules. By utilizing quasi-direct-drive motors, the module eliminates the need for dedicated force-sensing mechanisms, significantly simplifying the overall design, while also supporting flexible wire routing in multiple directions, various module-to-module connections, and even the use of the module body itself as a structural component. QDD-MM integrates these capabilities into a reusable muscle module, and its design is openly available at https://github.com/haraduka/qddmm. We developed tendon-driven robots with one joint and either two or three muscles, as well as a partial musculoskeletal humanoid, using the proposed QDD-MM and verified their effectiveness. We expect that this muscle module will democratize tendon-driven robotics and further accelerate progress in the field.

0.71

Integrated Design and Reproducible Feasibility Analysis of a Four-Wheel Rover with Packet-Commanded Imaging, LiDAR Ranging, and Learning-Assisted Target Recognition

cs.RO ·2026-10-27 ·Sabik Bin Sultan, Shafi Bin Sultan, Safwan Sadad, Aranya Abeer Khan Prapya, Maria Sultan
benchmark similarity 0.35
Abstract · Research Manuscript for NASA HERC 2027

This study develops an integrated, reproducible design assessment for a four-wheel educational rover intended for the high-school remote-control division of the 2027 NASA Human Exploration Rover Challenge. The architecture combines commercial differential drive control, independently sprung wheel carriers, separate drive and task batteries, and a Raspberry Pi-based subsystem that executes received imaging and ranging commands. The analysis reconciles component lists with dimensioned computer-aided design views, derives mobility and electrical constraints, and connects sensor geometry to command execution. At the estimated mass of 10.919 kg, a 215 mm wheel rotating at 200 RPM produces a theoretical rolling speed of 8.105 km/h; consequently, the nominal motor label does not establish compliance with an 8 km/h design ceiling. A steady 20-degree climb requires at least 1.255 newton-meters per wheel under an assumed rolling-resistance coefficient of 0.10 and equal torque sharing. At 50 ft, an ideal 12-inch feature spans approximately 71 pixels across a full-resolution Camera Module 3 Standard image, while a 1-degree pointing error displaces the ranging ray by approximately 266 mm. An executed synthetic benchmark compares color-geometry rules and two linear support-vector classifiers on 2,400 generated board crops with scene-disjoint evaluation. A separate reference command executor is checked using mocked hardware. These software results and analytical sensitivities support a testable development plan; the study does not report physical rover trials. The principal contribution is a traceable connection between component choices, failure mechanisms, quantitative design limits, and reproducible verification tasks.

0.18