CS Paper Radar

High-Performance Sensorless Control for High-Speed PMSM with Current Source Inverters

Nail Tosun, Devinda Molligoda, Xu Deng, Barrie Mecrow

eess.SY ·submitted 2026-09-22 08:45 UTC · v1
publishedunusual

Abstract

Current source inverters (CSIs) are emerging as competitive alternatives to voltage source inverters (VSIs) for high-speed motor drives because they inherently suppress harmonic currents, offer output-voltage boosting, and reduce motor-side electromagnetic interference. Sensorless control of CSI-fed permanent magnet synchronous machines (PMSMs) remains less mature than VSI counterparts, primarily because conventional implementations require measurement of all circuit state variables. This paper proposes a weak-resonance-based approximation that reconstructs stator currents from inverter modulation commands and feedforward capacitor-current estimation, thereby reducing the sensing requirement to the dc-link current and two terminal voltages. The proposed observer--PLL structure is analysed for computational complexity and validated through simulations and experiments on a 100~W, 100~krpm GaN-based two-stage CSI prototype (buck + CSI). Quantitative results demonstrate accurate rotor-position tracking and high-bandwidth operation while maintaining the reduced sensor set. Proposed method performs well in simulation and experiment, achieving a position estimation error below $5^\circ$ at 100~krpm.

Comment
Accepted, and presented at ICEM 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Temporal Regression-Based Model-Free Sensorless Control of Permanent Magnet Synchronous Motor

eess.SY ·2026-09-24 ·Fobao Zhou, Yang Shen, Xueyan Wang, Zhenxiao Yin, Yujia Zhang +2 more
similarity 0.64
Abstract

To address the widespread sensitivity of surface-mounted permanent magnet synchronous motor (SPMSM) sensorless control to motor parameters, this paper proposes a temporal regression-based model-free sensorless control (TFC) method. First, voltage integrals and current increments over consecutive short intervals are stacked to construct a finite window regression, in which the unknown stator inductance appears as a common scalar coefficient. Second, a projection operator constructed from the stacked current increments eliminates the inductance term, and a least-squares formulation is developed to reconstruct the rotor flux vector. Meanwhile, the analysis of the projected regression and current-flux geometry establishes a two-dimensional direction vector whose components share a common amplitude containing the stator resistance and flux linkage. This amplitude cancels during position extraction. By setting the resistance reference to zero, the proposed method estimates the position without specifying the stator resistance, inductance, or flux linkage. Finally, experimental results verify the effectiveness of the proposed TFC method.

0.32

Parameter-Robust Sensorless Control of IPMSM Drives With Adaptive Flux Observer

eess.SY ·2026-09-30 ·Fobao Zhou, Zhenxiao Yin, Xueyan Wang, Yang Shen, Yuanfeng Qu +1 more
similarity 0.64
Abstract

To address parameter sensitivity commonly in interior permanent magnet synchronous motor (IPMSM) sensorless control, this paper proposes a parameter-robust control framework by extending the adaptive flux observer from surface-mounted PMSM to salient-pole machines. First, parameter mismatches are interpreted as an equivalent flux vector with $d$-axis and $q$-axis components. Permanent magnet flux, $d$-axis inductance, and resistance mismatches are mapped to the $d$-axis flux component, whereas $q$-axis inductance mismatch is mapped to the $q$-axis component. Then, a scalar adaptive flux update is designed to compensate the $d$-axis flux variation by tracking the equivalent flux magnitude. Since the $q$-axis component rotates the observed flux direction and cannot be eliminated by scalar adaptation, a high-frequency $q$-axis voltage injection method is introduced to identify the $q$-axis inductance. Meanwhile, stability analysis proves bounded equivalent flux magnitude tracking and identifies the residual tangential flux responsible for position error. Finally, experimental results show that the proposed method does not require precise resistance, $d$-axis inductance, or flux, while the $q$-axis inductance is provided by online identification.

0.10

Model-Free Output-Admittance Reshaping for Stability Enhancement of Grid-Connected Inverters

eess.SY ·2026-10-23 ·Runnan Wang, Wanrong Li, Huawei Yuan, Sinan Li
published similarity 0.55
Abstract · Accepted at the 2026 IEEE PES Australasian Universities Power Engineering Conference (AUPEC)

Grid-connected inverters can be unstable when their current-control loops interact with an uncertain external network. Returning the existing controller to improve damping also alters current tracking because tracking dynamics and output admittance are coupled. This paper adds a local model-free control (MFC) loop around the existing current controller to reduce output admittance while closely preserving nominal current-tracking dynamics. The added loop uses local inverter parameters without an external grid or neighbouring converter model. A Norton formulation separates reference tracking from the current response to terminal-voltage disturbances and establishes a tracking-preservation condition for admittance reshaping. Reducing the disturbance response makes the inverter behave more like an ideal controlled current source. Averaged-model simulations show reductions exceeding 65% in the magnitudes of all four dq output-admittance elements over 10-200 Hz, with closely preserved current-tracking dynamics. Generalised Nyquist analysis predicts small-signal stability for all sampled grid-impedance cases with MFC, compared with 90.0% without MFC.

0.28

Equivalent Flux Compensation for SPMSM Sensorless Control under Parameter Mismatch

eess.SY ·2026-09-24 ·Fobao Zhou, Jiaqiao Liang, Zhenxiao Yin, Xueyan Wang, Yang Shen +2 more
similarity 0.53
Abstract

Parameter mismatch is the main source of rotor position estimation error in sensorless control of surface-permanent magnet synchronous motors (SPMSMs). To this end, this paper proposes a simple yet efficient equivalent flux compensation (EFC) method that directly estimates the equivalent flux disturbance caused by parameter mismatches in real time. First, the equivalent flux disturbance caused by parameter mismatches is derived from a nonlinear flux observer. Second, a flux update law is proposed to minimize both magnitude and directional errors by leveraging geometric error together with the derived equivalent flux disturbance. To enhance numerical stability, a saturation function is introduced to improve gradient continuity in the update process. Additionally, Lyapunov analysis is employed to ensure the stability of the proposed update law, from which the corresponding error bounds and convergence properties are derived. Finally, experimental results validate that the proposed method fully compensates for the steady-state effects of resistance and flux mismatches, and partially mitigates the influence of inductance variation, effectively constraining the position estimation error within a relatively small range.

0.56

Model-Free Current Control of Permanent Magnet Synchronous Motors via ESO-Based Disturbance Feedforward and Data-Driven H-infinity Residual Feedback

eess.SY ·2026-09-22 ·YongBo Li, Shuang Liang, HongWei Ma
similarity 0.51
Abstract · 20 pages, 14 figures

This paper proposes a model-free current control method for permanent magnet synchronous motors (PMSMs) based on disturbance feedforward and residual feedback. An ultra-local current model incorporates motor dynamics, parameter uncertainties, cross-coupling effects, and other nonideal factors into generalized lumped disturbances. An extended state observer (ESO) estimates these lumped disturbances and compensates for them through feedforward action, transforming the original PMSM current-control problem into regulation of a simplified post-compensation residual system. A state-feedback H-infinity controller for the residual system is then learned directly from operating data using off-policy integral reinforcement learning. Owing to the simplified residual dynamics, the value function and control policies are parameterized in quadratic and linear forms, reducing the learning problem to low-dimensional parameter estimation without neural-network approximation. The proposed method requires neither prior knowledge nor online identification of PMSM electrical parameters: input-gain mismatch is incorporated into the ESO-estimated lumped dynamics, while the residual-feedback policy is obtained from operating data. Comparative simulations against deadbeat predictive current control, model-based H-infinity control, and model-free predictive current control show fast current tracking, low current distortion, and strong robustness to large parameter variations. With the learned H-infinity policy fixed and without retraining or retuning, nearly unchanged control performance is maintained when stator resistance, stator inductance, and permanent-magnet flux linkage are simultaneously varied to 20% and 200% of their nominal values.

0.29

PLL-Less Synchronization of Grid-Following Converters Using a Voltage-Driven Frenet Frame

eess.SY ·2026-11-13 ·Jinhui Chen, Huadong Sun, Shiyun Xu, Bing Zhao, Peng Han +1 more
benchmark similarity 0.47
Abstract

In grid-following converters, the synchronization path can transmit voltage disturbances to the current loop under weak or unbalanced grid conditions. This paper develops a Frenet-frame controller that derives its axes from the integral curve of the measured voltage at the point of common coupling. The tangential current governs active power, while the normal and binormal currents govern the transverse components of non-active power. Feedforward terms derived from the output filter model compensate curvature and torsion coupling, yielding identical nominal current dynamics across the axes. The controller operates without a phase-locked loop or sequence extraction. A reduced transverse model accounts for the finite bandwidth of geometric rate reconstruction and predicts a reduction in low-frequency coupling from voltage disturbances to current. Controller hardware-in-the-loop tests using real-time simulation of a three-phase four-wire converter show the shortest settling time after an active power reference step and the smallest peak power deviations during balanced voltage disturbances among the tested controllers. Under single-phase voltage unbalance, the method reduces peak binormal current and maximum phase-current total harmonic distortion relative to both benchmarks. It also settles to the commanded power in a weak-grid connection test where the phase-locked loop benchmark exhibits sustained oscillations.

0.29

From Continuous Design to Delay-Aware Discrete Synthesis: Guaranteed High-Bandwidth Joint Control for PMSM Drives

cs.RO ·2026-08-14 ·Edmundo Pozo Fortunić, Mehmet C. Yildirim, Sami Haddadin
similarity 0.44
Abstract · 9 pages, 3 figures

The increasing dynamic demands of modern robotic joints require current controllers to achieve high bandwidth over wide operating ranges of speed, acceleration, and torque, where communication, computation, and discrete-time effects can no longer be neglected. Conventional PMSM current controllers are typically designed in continuous time and subsequently discretized, leaving the sampling frequency and the impact of implementation delays largely to heuristic selection and iterative validation. This paper introduces a task-aware, delay-extended discrete-time joint model that explicitly accounts for physical communication and computation delays and enables direct synthesis of a discrete PI current controller with prescribed bandwidth and delay guarantees throughout the operating envelope. The framework analytically determines the minimum required sampling frequency, controller gains, and DC-link voltage needed to satisfy the specified motor and joint performance. Simulations across a range of dynamic requirements validate the methodology and demonstrate substantially reduced sampling-frequency and DC-link-voltage requirements compared with conventional continuous-time-based design. Experiments on a newly developed custom robotic joint further validate the proposed framework under real embedded implementation conditions.

0.10

Comparative Assessment of Frequency Scans using EMT and RMS Models

eess.SY ·2026-08-27 ·Clea Bürgel, Gustavo Valverde, Gabriela Hug
similarity 0.42
Abstract

Frequency scans of inverter and grid impedances are crucial for assessing small-signal stability and system strength in inverter-dominated power systems. This paper compares frequency-scan results for several generating units, including a synchronous generator, grid-following, and grid-forming inverters, using fully dq electromagnetic transient and root-mean-square (RMS) models in Simulink. The scans are performed for the same device rating and operating point. Frequency scans and time-domain simulations show that the RMS models are valid only at low frequencies. We find that the current-controlled grid-forming inverter is more difficult to represent in RMS than the voltage-controlled grid-forming inverter. However, including the inner voltage-control loops improves the accuracy of the RMS representation. The paper also investigates the influence of generator and grid impedance on the total system impedance seen from the point of common coupling and relates the oscillatory modes and zeros of the system to peaks and dips in the first and second singular values of the system impedance, respectively.

0.22