CS Paper Radar

Temporal Regression-Based Model-Free Sensorless Control of Permanent Magnet Synchronous Motor

Fobao Zhou, Yang Shen, Xueyan Wang, Zhenxiao Yin, Yujia Zhang, Yuanfeng Qu, Hang Zhao

eess.SY ·submitted 2026-09-24 09:27 UTC · v1

Abstract

To address the widespread sensitivity of surface-mounted permanent magnet synchronous motor (SPMSM) sensorless control to motor parameters, this paper proposes a temporal regression-based model-free sensorless control (TFC) method. First, voltage integrals and current increments over consecutive short intervals are stacked to construct a finite window regression, in which the unknown stator inductance appears as a common scalar coefficient. Second, a projection operator constructed from the stacked current increments eliminates the inductance term, and a least-squares formulation is developed to reconstruct the rotor flux vector. Meanwhile, the analysis of the projected regression and current-flux geometry establishes a two-dimensional direction vector whose components share a common amplitude containing the stator resistance and flux linkage. This amplitude cancels during position extraction. By setting the resistance reference to zero, the proposed method estimates the position without specifying the stator resistance, inductance, or flux linkage. Finally, experimental results verify the effectiveness of the proposed TFC method.

Closest papers

Nearest neighbours by meaning across the whole index.

Equivalent Flux Compensation for SPMSM Sensorless Control under Parameter Mismatch

eess.SY ·2026-09-24 ·Fobao Zhou, Jiaqiao Liang, Zhenxiao Yin, Xueyan Wang, Yang Shen +2 more
similarity 0.68
Abstract

Parameter mismatch is the main source of rotor position estimation error in sensorless control of surface-permanent magnet synchronous motors (SPMSMs). To this end, this paper proposes a simple yet efficient equivalent flux compensation (EFC) method that directly estimates the equivalent flux disturbance caused by parameter mismatches in real time. First, the equivalent flux disturbance caused by parameter mismatches is derived from a nonlinear flux observer. Second, a flux update law is proposed to minimize both magnitude and directional errors by leveraging geometric error together with the derived equivalent flux disturbance. To enhance numerical stability, a saturation function is introduced to improve gradient continuity in the update process. Additionally, Lyapunov analysis is employed to ensure the stability of the proposed update law, from which the corresponding error bounds and convergence properties are derived. Finally, experimental results validate that the proposed method fully compensates for the steady-state effects of resistance and flux mismatches, and partially mitigates the influence of inductance variation, effectively constraining the position estimation error within a relatively small range.

0.56

High-Performance Sensorless Control for High-Speed PMSM with Current Source Inverters

eess.SY ·2026-09-22 ·Nail Tosun, Devinda Molligoda, Xu Deng, Barrie Mecrow
publishedunusual similarity 0.64
Abstract · Accepted, and presented at ICEM 2026

Current source inverters (CSIs) are emerging as competitive alternatives to voltage source inverters (VSIs) for high-speed motor drives because they inherently suppress harmonic currents, offer output-voltage boosting, and reduce motor-side electromagnetic interference. Sensorless control of CSI-fed permanent magnet synchronous machines (PMSMs) remains less mature than VSI counterparts, primarily because conventional implementations require measurement of all circuit state variables. This paper proposes a weak-resonance-based approximation that reconstructs stator currents from inverter modulation commands and feedforward capacitor-current estimation, thereby reducing the sensing requirement to the dc-link current and two terminal voltages. The proposed observer--PLL structure is analysed for computational complexity and validated through simulations and experiments on a 100~W, 100~krpm GaN-based two-stage CSI prototype (buck + CSI). Quantitative results demonstrate accurate rotor-position tracking and high-bandwidth operation while maintaining the reduced sensor set. Proposed method performs well in simulation and experiment, achieving a position estimation error below $5^\circ$ at 100~krpm.

0.40

Parameter-Robust Sensorless Control of IPMSM Drives With Adaptive Flux Observer

eess.SY ·2026-09-30 ·Fobao Zhou, Zhenxiao Yin, Xueyan Wang, Yang Shen, Yuanfeng Qu +1 more
similarity 0.58
Abstract

To address parameter sensitivity commonly in interior permanent magnet synchronous motor (IPMSM) sensorless control, this paper proposes a parameter-robust control framework by extending the adaptive flux observer from surface-mounted PMSM to salient-pole machines. First, parameter mismatches are interpreted as an equivalent flux vector with $d$-axis and $q$-axis components. Permanent magnet flux, $d$-axis inductance, and resistance mismatches are mapped to the $d$-axis flux component, whereas $q$-axis inductance mismatch is mapped to the $q$-axis component. Then, a scalar adaptive flux update is designed to compensate the $d$-axis flux variation by tracking the equivalent flux magnitude. Since the $q$-axis component rotates the observed flux direction and cannot be eliminated by scalar adaptation, a high-frequency $q$-axis voltage injection method is introduced to identify the $q$-axis inductance. Meanwhile, stability analysis proves bounded equivalent flux magnitude tracking and identifies the residual tangential flux responsible for position error. Finally, experimental results show that the proposed method does not require precise resistance, $d$-axis inductance, or flux, while the $q$-axis inductance is provided by online identification.

0.10

Model-Free Current Control of Permanent Magnet Synchronous Motors via ESO-Based Disturbance Feedforward and Data-Driven H-infinity Residual Feedback

eess.SY ·2026-09-22 ·YongBo Li, Shuang Liang, HongWei Ma
similarity 0.54
Abstract · 20 pages, 14 figures

This paper proposes a model-free current control method for permanent magnet synchronous motors (PMSMs) based on disturbance feedforward and residual feedback. An ultra-local current model incorporates motor dynamics, parameter uncertainties, cross-coupling effects, and other nonideal factors into generalized lumped disturbances. An extended state observer (ESO) estimates these lumped disturbances and compensates for them through feedforward action, transforming the original PMSM current-control problem into regulation of a simplified post-compensation residual system. A state-feedback H-infinity controller for the residual system is then learned directly from operating data using off-policy integral reinforcement learning. Owing to the simplified residual dynamics, the value function and control policies are parameterized in quadratic and linear forms, reducing the learning problem to low-dimensional parameter estimation without neural-network approximation. The proposed method requires neither prior knowledge nor online identification of PMSM electrical parameters: input-gain mismatch is incorporated into the ESO-estimated lumped dynamics, while the residual-feedback policy is obtained from operating data. Comparative simulations against deadbeat predictive current control, model-based H-infinity control, and model-free predictive current control show fast current tracking, low current distortion, and strong robustness to large parameter variations. With the learned H-infinity policy fixed and without retraining or retuning, nearly unchanged control performance is maintained when stator resistance, stator inductance, and permanent-magnet flux linkage are simultaneously varied to 20% and 200% of their nominal values.

0.29

Real-Time Transient Response Optimization

eess.SY ·2026-08-22 ·Anahida Kanade, Djan Tanova, Steve Conner, Taner Dosluoglu
published similarity 0.45
Abstract · 6 pages, 9 figures, 1 table. Technical correspondence of original research and data that has not yet been accepted for publication in any jo…

Use of artificial intelligence in motor control applications that can be deployed within the microcontrollers need to comply with real-time demands of motor control systems. A supplementary controller approach that can be integrated within existing microcontrollers is presented. The proposed approach is implemented on a weeteq motor control integrated circuit and tested in the lab. A complete unsupervised motor control deployment solution was developed, and the real-time system response correction demonstrated under dynamic loads measured with and without the supplementary controller. The solution provides 100% coverage of real-time data at control loop sample rate and model inference period between 100usec and 1msec. The importance of latency for reduction of dynamic regulation margin during transient response is demonstrated with up to 68% reduction of the system response error. A novel key performance indicator based on principal components transform is introduced that provides a quantitative figure of merit for improvement of the transient response, in terms of the dynamic regulation margin, stability considerations and iterative improvements of consecutive regression model outputs. The significant events related to dynamic changes in the equipment and external operating conditions are detected at milliseconds resolution and recorded as highly compressed vectors representing deviation of the system response from linear steady state conditions. The resolution in time and accuracy of this vector data will enable a new level of system level optimisation that has not been possible using the time series data from IoT sensors in current equipment health monitoring solutions.

0.36

Physics-Guided Inferencer-in-the-Loop Digital-Twin for Real-Time Adaptive Emulation of Nonlinear PMSMs

eess.SY ·2026-10-28 ·Songyang Zhang, Yuzhong Zhang, Venkata Dinavahi
similarity 0.44
Abstract

A real-time digital-twin (RTDT) of a permanent magnet synchronous machine (PMSM) allows drive controllers to be tested in hardware-in-the-loop (HIL) before they meet the real machine. Its machine model rests on identified parameters or flux look-up tables (LUTs) from finite-element analysis (FEA) or characterization tests; the maps are regenerated offline when the machine changes, and online estimators track a few parameters such as resistance and PM flux. This article makes the executed model learnable from reference data. A physics-guided machine learning (PGML) network advances the currents and predicts torque in one step, trained with analytical one-step labels. In the proposed Inferencer-in-the-Loop (IIL) architecture, a GPU retrains the network while a field-programmable gate array (FPGA) executes the last accepted weights. For damper circuits, shifted parameters, and an FEA-calibrated saturated machine, one kernel form reaches average normalized mean absolute errors (NMAEs) of 0.19%-0.67% at measured FPGA kernel latencies of 0.30-0.34 $μ$s, and retraining for a shifted machine nears its final loss within 94 s. On a magnetically linear 200-W drive, a residual form corrects the analytical step and learns its physical parameters from operating data; each step takes under 2.5 $μ$s, 20 times faster than real time and ahead of the physical drive's measurements even at 20-kHz sampling. On six held-out runs (1193 s), its $i_q$ error is 5.9%-9.4% of measured RMS, against 10.4%-13.2% for an independently fitted grey-box model, and over 30 min of loaded heating its online-updated heads track a 4.1% winding-resistance rise with an RMS error of 0.44 m$Ω$.

0.29

Tilt-Rotor Quadcopter with Learned Residual Control and Mode-Dependent State Estimation

cs.RO ·2026-10-22 ·Ninad Joshi, Prabhat Kumar
similarity 0.43
Abstract · 5 figures

Tilt-rotor quadcopters redirect thrust for translation without banking, but complicate modeling, state estimation, and disturbance rejection. This paper presents a simulation-based flight stack for a \SI{2.00}{\kilo\gram} tilt-rotor quadcopter. The system uses a six-degree-of-freedom nonlinear model with first-order motor dynamics and two-axis rotor tilt, parameterized using a 3D CAD model. A cascaded PD controller commands forward and lateral tilt angles. A 14-state EKF fuses sensor data across hover, early-transition, and transition modes using a hysteretic (Schmitt-trigger) classifier to prevent covariance discontinuities. Because the proportional position loop leaves a steady-state offset under constant wind, a small bounded neural residual is added on top of the unmodified PD controller. It is trained by behavioral cloning from a teacher with privileged access to the true wind, while the deployed network never observes wind. In simulation, the EKF achieves a post-settling position root mean square error (RMSE) of \SI{0.226}{\metre} (horizontal) and \SI{0.03}{\metre} (vertical) and an attitude RMSE below \SI{0.8}{\degree}, and it estimates a wind velocity of $(\num{2.0}, \num{-1.2})\,\unit{\metre\per\second}$ to within \SI{0.15}{\metre\per\second} per axis. The residual reduces steady-state station-keeping error under wind by approximately \SI{49}{\percent}, from \SI{0.117}{\metre} to \SI{0.060}{\metre} at \SI{1.5}{\metre\per\second} and from \SI{0.319}{\metre} to \SI{0.162}{\metre} at an out-of-distribution \SI{3.9}{\metre\per\second}. The framework provides a basis for hardware-in-the-loop and flight-test studies.

0.29

From Continuous Design to Delay-Aware Discrete Synthesis: Guaranteed High-Bandwidth Joint Control for PMSM Drives

cs.RO ·2026-08-14 ·Edmundo Pozo Fortunić, Mehmet C. Yildirim, Sami Haddadin
similarity 0.40
Abstract · 9 pages, 3 figures

The increasing dynamic demands of modern robotic joints require current controllers to achieve high bandwidth over wide operating ranges of speed, acceleration, and torque, where communication, computation, and discrete-time effects can no longer be neglected. Conventional PMSM current controllers are typically designed in continuous time and subsequently discretized, leaving the sampling frequency and the impact of implementation delays largely to heuristic selection and iterative validation. This paper introduces a task-aware, delay-extended discrete-time joint model that explicitly accounts for physical communication and computation delays and enables direct synthesis of a discrete PI current controller with prescribed bandwidth and delay guarantees throughout the operating envelope. The framework analytically determines the minimum required sampling frequency, controller gains, and DC-link voltage needed to satisfy the specified motor and joint performance. Simulations across a range of dynamic requirements validate the methodology and demonstrate substantially reduced sampling-frequency and DC-link-voltage requirements compared with conventional continuous-time-based design. Experiments on a newly developed custom robotic joint further validate the proposed framework under real embedded implementation conditions.

0.10