CS Paper Radar

Model predictive traction control system based on the Koopman operator

Josip Kir Hromatko, Šandor Ileš

eess.SY ·submitted 2026-08-26 13:03 UTC · v1
publishedcode/data

Abstract

Due to their importance, traction control and anti-lock braking systems have become standard equipment in modern vehicles. However, accurate models of tire dynamics are often difficult to obtain and usually include nonlinearities, making their use in control systems challenging. This paper describes a traction control system based on model predictive control and Koopman operator theory, which aims to approximate nonlinear systems with linear ones through a state space transformation. A linear model predictive controller based on the Koopman predictor is compared to a standard nonlinear model predictive controller. Experiments in a high-fidelity vehicle dynamics simulation environment show a comparable reference tracking performance of the two controllers, with a reduced execution time for the proposed Koopman operator-based algorithm, both on a standard PC and embedded hardware.

Comment
6 pages, 4 figures; associated code available at https://github.com/PVDC-project/pvdc-kmpc-traction-control
Journal ref
Proc. 2024 28th Int. Conf. Syst. Theory Control Comput. (ICSTCC), 2024, pp. 26-31
DOI
10.1109/ICSTCC62912.2024.10744655

Closest papers

Nearest neighbours by meaning across the whole index.

Autonomous path following using data-driven predictive control

eess.SY ·2026-08-25 ·Josip Kir Hromatko, Marko Švec, Šandor Ileš
published similarity 0.61
Abstract · 6 pages, 6 figures

Predictive control based on an informative system trajectory, instead of a physics-based model, has received significant attention in recent years. This paper investigates the potential of using such data-driven control for vehicle dynamics control and autonomous path following. By considering the path following problem in the error space, the underlying system is approximately linear and existing results for data-driven predictive control can be applied. Also, scheduling based on longitudinal speed can be readily included. The proposed control algorithm was tested on two different lane change maneuvers in a high-fidelity simulation environment.

0.36

LLA-MPC on Embedded Hardware: Rapid Adaptive Control with Thousands of Parallel Models

cs.RO eess.SY ·2026-10-02 ·Henry Z. Liao, Maitham F. AL-Sunni, John M. Dolan
publishedcode/data similarity 0.60
Abstract · This work has been accepted in the Sim2Real and Classical Control: From Rigorous Theory to Data-Driven Robotics Workshop at the 2026 IEEE/RS…

We present a generalized implementation of Look-Back and Look-Ahead Adaptive Model Predictive Control (LLA-MPC), a learning-free framework for real-time, rapid adaptive system identification and control. The original formulation was demonstrated only in simulation, for autonomous racing with a fixed model structure. Our implementation has modular dynamics and integrators, and we validate it on the F1TENTH platform under constrained computation and noisy state estimation. The system identifies tire parameters online by evaluating thousands of candidate models in real time on an embedded computer. Experiments with low-friction tires across changing surfaces show that LLA-MPC completes high-speed tracking tasks where a fixed nominal model fails. Code, videos, and our related work are available at: https://lla-control.github.io.

0.56

High-Speed Forward and Reverse Tractor-Trailer Driving with Learned Vehicle Dynamics

cs.RO eess.SY ·2026-11-15 ·Aaron Chen, David Shen, Taekyung Kim, Kaleb Ben Naveed, Dimitra Panagou
code/data similarity 0.59
Abstract · The first three authors contributed equally to this work. Project page: https://ds12a.github.io/drift-with-trailer/

Tractor-trailer systems are difficult to control, especially unstable during reverse motion, and their dynamics depend on difficult-to-measure factors, including road friction and suspension coefficients. We introduce a learned dynamics model for tractor-trailer control and compare it with a reduced-order dynamics model with Fiala tire forces as an analytic baseline. Specifically, we compare a model predictive path integral (MPPI) controller that uses the learned dynamics model to an MPPI controller that uses the analytic model, as well as to three additional baseline controllers. In the main closed-loop tracking experiments across four simulated environments, MPPI with learned dynamics achieves mean speeds closer to the target magnitudes and lower root-mean-square (RMS) hitch angles than MPPI with the analytic model at every tested setpoint, with higher completion rates in seven of eight reverse configurations.

0.17

Wheel-loader V-Cycle Automation with Deep Koopman MPC

cs.RO eess.SY ·2026-09-22 ·Armin Abdolmohammadi, Navid Mojahed, Dinesh Kumar, Bahram Ravani, Shima Nazari
similarity 0.59
Abstract · 8 pages, 4 figure

The repeated forward-reverse maneuvers performed by wheel loaders during earthmoving operations make them well suited for automation. However, the nonlinear dynamics of articulated vehicles and complex vehicle-terrain interactions limit the effectiveness of conventional model-based approaches. This paper presents a hierarchical framework that combines long-horizon geometric planning with data-driven predictive control for autonomous wheel-loader operation. A reduced-order articulated kinematic model is used to generate the maneuver geometry, where the forward and reverse trajectories are jointly optimized through a shared intermediate state. To capture the vehicle dynamics, two data-driven deep bilinear Koopman models are learned for the forward and reverse motions using data generated from high-fidelity simulations in Algoryx Dynamics. The learned Koopman representations are subsequently incorporated into a computationally efficient model predictive control (MPC) formulation for trajectory tracking. The resulting controller operates in real time within a 50-ms execution loop. High-fidelity simulation results demonstrate that the proposed end-to-end framework enables accurate and computationally efficient execution of wheel-loader V-cycle maneuvers, providing a promising approach toward autonomous operation of articulated heavy-duty machinery.

0.26

Mapping Tire-Road Friction Coefficients Along Driven Trajectories

cs.RO ·2026-10-09 ·Risto Ojala
benchmarkcode/data similarity 0.59
Abstract

Information of the tire-road friction coefficient is critical for intelligent vehicle systems, as friction establishes the limits at which the vehicle can be manoeuvred without loss of control. While there is extensive literature on online friction estimation, no previous studies have explored post-processing and mapping friction coefficients along a driven trajectory based on recorded sensor data. Mapped friction information could be shared by connected vehicles, enabling proactive measures in low-friction areas. This paper presents an offline post-processing method, FrictionMap, for mapping friction coefficients from recorded driving data. The method operates on commonly available on-board vehicle sensor information, and requires only a basic vehicle parameter set and a slip threshold as prior knowledge. FrictionMap runs an extended Kalman filter combined with a Rauch-Tung-Striebel smoother to estimate vehicle dynamics. Data points where the friction limit is observable are identified by filtering points based on tire slip. A Gaussian process is fitted to these points to acquire a continuous estimate of the friction coefficient along the trajectory. FrictionMap is validated via a simulation study, and shown to outperform commonly used online friction estimation techniques. The code implementation and the simulation benchmark are released as open-source after paper acceptance to enable further research.

0.34

Data-Driven Predictive Control for Autonomous Vehicle Racing under Varying Friction

eess.SY cs.RO ·2026-11-16 ·Julius Beerwerth, Julius Tischbein, Bassam Alrifaee
code/datahot direction similarity 0.59
Abstract · 8 pages, 4 figures. Submitted to the 2027 European Control Conference (ECC). Code and data: https://github.com/bassamlab/multisurface-racing…

Data-driven predictive control (DPC) predicts future outputs by combining recorded input-output trajectory data such that the combined trajectory approximately matches a measured initial trajectory and tracks a provided reference. This paper investigates to what extent and under which conditions DPC using data pooled across operating conditions retains the prediction accuracy of DPC using data from the current operating condition. In autonomous vehicle racing, the tire-road friction varies between racetrack sections and tire sets. If the initial trajectory and the recorded data originate from different frictions, prediction accuracy of DPC degrades. Ensuring the frictions match requires knowing the friction during recording and estimating the current friction explicitly. Instead, we pool data recorded at different frictions. We compare the prediction accuracy of DPC using data recorded under the current friction (matched), a different friction (mismatched) and data pooled from both frictions. We evaluate in simulation and small-scale vehicle experiments in the Cyber-Physical Mobility Lab (CPM Lab). Our results show that pooled data keep the multi-step root-mean-square prediction error within 1.5 times that of matched data, whereas mismatched data increase it by a factor of 2.2 to 3.4. To assess how this prediction accuracy carries over to control, we evaluate the tracking error from the raceline in closed loop. In simulation, DPC with pooled data tracks comparably to nonlinear model predictive control (13.7 cm versus 13.3 cm) and close to DPC with matched data in the CPM Lab, differing by 0.1 cm on the low-friction tires (1.6 cm versus 1.5 cm) and by 0.2 cm on the high-friction tires (0.9 cm versus 1.1 cm). DPC thus provides partial adaptation to varying friction, without a dedicated adaptation method.

0.59

Vehicle Drift Emergence: Continuous Evolution from Grip Driving to the Handling Limit via Boundary Exploration Learning Model Predictive Control

cs.RO ·2026-08-28 ·Sheng Zhao, Binh-Minh Nguyen, Hangyu Lu, Xiaodong Wu
similarity 0.57
Abstract

Automated drift controllers commonly track a prescribed drift equilibrium, sideslip reference, or trajectory. These formulations establish how to execute drift, whereas the continuous transition from grip driving to drift near the handling limit remains unresolved. This paper defines drift emergence in a repetitive lap time minimization task, where neither the controller objective nor the reward contains an explicit drift reference. A boundary exploration learning model predictive controller (BE-LMPC) constructs an empirical safe set and a locally shifted terminal cost from completed laps. By iteratively improving spatial speed allocation under a fixed global speed bound, the controller progressively explores larger sideslip and yaw rate envelopes while preserving recoverability. As lap performance improves, sustained sideslip and pronounced yaw motion emerge while the rear axle approaches saturation. Analysis shows that, when external conditions vary smoothly, the transition from tire adhesion to sliding does not itself cause abrupt changes in tire force or vehicle state. The combined-slip Fiala model satisfies this continuity condition at the transition. At a tire road friction coefficient of 0.6, lap time decreases from 49.95 s on Lap~3 to 25.50 s on Lap~12, with drift first emerging on Lap~11. Lap~12 reaches 16.5$^\circ$ sideslip and 0.894 rear axle utilization. In contrast, no drift is detected for friction coefficients from 0.8 to 1.2; at 1.2, a similar peak speed is achieved with only 0.483 rear axle utilization. These results characterize drift as a conditional continuation of limit handling that emerges when increasing performance demand approaches the available tire capacity, rather than as a separately prescribed motion mode.

0.32

Traffic State Prediction and Control Using a Koopman Operator Framework with Polynomial Observables

eess.SY ·2026-10-14 ·Shakib Mustavee, Arvind Singh, Shaurya Agarwal
similarity 0.57
Abstract

In this paper, we develop a Koopman operator framework for modeling and control of traffic flow governed by the Lighthill--Whitham--Richards (LWR) conservation law. We show that the nonlinear dynamics induced by the Greenshields flow--density relation naturally motivate a dictionary of polynomial observables, while the controlled dynamics become bilinear in the lifted Koopman coordinates. A reduced-order Koopman model is identified from spatio-temporal traffic-density snapshots and used as the prediction model in a model predictive control (MPC) framework for ramp metering. The resulting Koopman-MPC is compared with two predictive control baselines that use, respectively, a fixed linearized LWR model and the nonlinear finite-volume LWR model. In a one-hour freeway experiment, the Koopman-based controller maintains the traffic density below the critical Greenshields value and closely reproduces the behavior of the nonlinear PDE-based MPC, with a maximum-density difference below 1%. The Koopman predictor also reduces the mean online model-evaluation cost by approximately one order of magnitude relative to the nonlinear PDE predictor. In contrast, the linearized LWR predictor is computationally cheaper but exhibits substantially larger prediction errors and yields a more conservative metering policy. These results demonstrate that the analytical structure of the nonlinear traffic conservation law can be exploited to construct an interpretable data-driven surrogate for efficient traffic prediction and control

0.24