CS Paper Radar

Mapping Tire-Road Friction Coefficients Along Driven Trajectories

Risto Ojala

cs.RO ·submitted 2026-10-09 18:51 UTC · v1
benchmarkcode/data

Abstract

Information of the tire-road friction coefficient is critical for intelligent vehicle systems, as friction establishes the limits at which the vehicle can be manoeuvred without loss of control. While there is extensive literature on online friction estimation, no previous studies have explored post-processing and mapping friction coefficients along a driven trajectory based on recorded sensor data. Mapped friction information could be shared by connected vehicles, enabling proactive measures in low-friction areas. This paper presents an offline post-processing method, FrictionMap, for mapping friction coefficients from recorded driving data. The method operates on commonly available on-board vehicle sensor information, and requires only a basic vehicle parameter set and a slip threshold as prior knowledge. FrictionMap runs an extended Kalman filter combined with a Rauch-Tung-Striebel smoother to estimate vehicle dynamics. Data points where the friction limit is observable are identified by filtering points based on tire slip. A Gaussian process is fitted to these points to acquire a continuous estimate of the friction coefficient along the trajectory. FrictionMap is validated via a simulation study, and shown to outperform commonly used online friction estimation techniques. The code implementation and the simulation benchmark are released as open-source after paper acceptance to enable further research.

Closest papers

Nearest neighbours by meaning across the whole index.

Data-Driven Predictive Control for Autonomous Vehicle Racing under Varying Friction

eess.SY cs.RO ·2026-11-16 ·Julius Beerwerth, Julius Tischbein, Bassam Alrifaee
code/data similarity 0.65
Abstract · 8 pages, 4 figures. Submitted to the 2027 European Control Conference (ECC). Code and data: https://github.com/bassamlab/multisurface-racing…

Data-driven predictive control (DPC) predicts future outputs by combining recorded input-output trajectory data such that the combined trajectory approximately matches a measured initial trajectory and tracks a provided reference. This paper investigates to what extent and under which conditions DPC using data pooled across operating conditions retains the prediction accuracy of DPC using data from the current operating condition. In autonomous vehicle racing, the tire-road friction varies between racetrack sections and tire sets. If the initial trajectory and the recorded data originate from different frictions, prediction accuracy of DPC degrades. Ensuring the frictions match requires knowing the friction during recording and estimating the current friction explicitly. Instead, we pool data recorded at different frictions. We compare the prediction accuracy of DPC using data recorded under the current friction (matched), a different friction (mismatched) and data pooled from both frictions. We evaluate in simulation and small-scale vehicle experiments in the Cyber-Physical Mobility Lab (CPM Lab). Our results show that pooled data keep the multi-step root-mean-square prediction error within 1.5 times that of matched data, whereas mismatched data increase it by a factor of 2.2 to 3.4. To assess how this prediction accuracy carries over to control, we evaluate the tracking error from the raceline in closed loop. In simulation, DPC with pooled data tracks comparably to nonlinear model predictive control (13.7 cm versus 13.3 cm) and close to DPC with matched data in the CPM Lab, differing by 0.1 cm on the low-friction tires (1.6 cm versus 1.5 cm) and by 0.2 cm on the high-friction tires (0.9 cm versus 1.1 cm). DPC thus provides partial adaptation to varying friction, without a dedicated adaptation method.

0.58

Floor Friction Assessment from Robot Tire-Surface Interaction

cs.RO ·2026-10-24 ·Kulbhushan Komarraju, Nathaniel Pearson, Yu Gu, Jason Gross
similarity 0.61
Abstract · 11 pages and 14 figures; Extended abstract submitted to IEEE/ION PLANS 2027, under review

Floor traction influences wheel-slip behavior, dead-reckoning accuracy, and the navigation performance of wheeled mobile robots that rely on wheel odometry. As these robots become increasingly common in GNSS-denied indoor environments, including automated manufacturing and retail facilities, their onboard measurements could also be used to characterize floor conditions and improve localization. In this study, a skid-steer robot was driven over five floor surfaces with distinct traction characteristics using commanded velocity profiles designed to induce wheel slip through repeated acceleration and direction reversal. Differences between the body velocity estimated from inertial sensing and the velocity obtained from wheel odometry were evaluated using the integrated relative-velocity error, phase-derived wheel-to-body response delay, and velocity-reversal response delay. Welch power spectral density analysis was additionally applied to characterize the frequency distribution of the velocity mismatch during positive and negative acceleration. Band-integrated spectral power, spectral centroid, and spectral decay rate were extracted from each recording and evaluated using linear discriminant analysis and multiclass classification. The response-delay measurements produced consistent surface-dependent trends, with the longest delays observed on soap and the shortest delays observed on carpet. The spectral features also provided clear separation among the tested surfaces, achieving a balanced classification accuracy of 97.1% under recording-level cross-validation. These results demonstrate that both the magnitude and frequency domain characteristics of wheel-to-body velocity mismatch contain useful information about tire-surface interactions. Such information could support surface recognition and the development of slip-aware wheel-odometry weighting within robot state-estimation frameworks.

0.25

Model predictive traction control system based on the Koopman operator

eess.SY ·2026-08-26 ·Josip Kir Hromatko, Šandor Ileš
publishedcode/data similarity 0.59
Abstract · 6 pages, 4 figures; associated code available at https://github.com/PVDC-project/pvdc-kmpc-traction-control

Due to their importance, traction control and anti-lock braking systems have become standard equipment in modern vehicles. However, accurate models of tire dynamics are often difficult to obtain and usually include nonlinearities, making their use in control systems challenging. This paper describes a traction control system based on model predictive control and Koopman operator theory, which aims to approximate nonlinear systems with linear ones through a state space transformation. A linear model predictive controller based on the Koopman predictor is compared to a standard nonlinear model predictive controller. Experiments in a high-fidelity vehicle dynamics simulation environment show a comparable reference tracking performance of the two controllers, with a reduced execution time for the proposed Koopman operator-based algorithm, both on a standard PC and embedded hardware.

0.78

Online Constraint Optimization-Based Indirect-Adaptive Robust Control for Autonomous Vehicles with Unknown Friction

eess.SY cs.RO ·2026-10-15 ·Yupeng Zhou, I-Chia Chang, Ziran Wang, Bin Yao
code/data similarity 0.59
Abstract

Friction uncertainty is a significant challenge for autonomous vehicle control, undermining feasibility and performance. This paper proposes a novel two-layer control framework to achieve vehicle motion control under large friction uncertainty by combining optimization-based planning with indirect adaptive robust control (IARC). The upper layer solves a constrained optimal control problem to generate a feasible trajectory that satisfies all the constraints in a time-optimal manner along the desired path. The lower layer, IARC, adapts the unknown parameters related to friction uncertainty and combines model compensation with robust feedback to ensure transient and steady-state tracking performance. An estimation monitor is designed to prevent poor learning when data indicate a model mismatch, while a smooth parameter reset reduces the estimated tire capacity and limits abrupt tightening of constraints. The updated parameters are fed back into the model and constraints in the planner, enabling trajectory replanning as friction conditions change. Simulation results indicate that the proposed method achieves accurate tracking of the desired trajectory and online friction adaptation under large friction uncertainty while ensuring time-optimal vehicle motion. The simulation results demos are available at https://github.com/TedZhou0603/CO-IARC.

0.27

Inertial Steering and Motion Prediction of Tracked Vehicles on Low-Adherence Surfaces

cs.RO eess.SY ·2026-10-28 ·Mathis Turgeon-Roy, Mohamed Ounally, Veronica Vannini, Olivier Roy, François Pomerleau
similarity 0.57
Abstract

Tracked vehicles are widely used in off-road applications, but their conventional motion models often rely on no-slip assumptions that become inaccurate on low-adherence surfaces. Rather than treating inertial effects arising from slip as a disturbance to be minimized, this work investigates how inertial effects arising from a moving mass can be deliberately exploited for steering on low-friction surfaces. A dynamic model for an articulated tracked vehicle with a passive trailer is developed, allowing inertial effects from trailer motion to be captured. The approach is experimentally evaluated on ice, where our dynamic model outperforms the kinematic baseline. We also propose a mixed dynamic-kinematic model to adapt predictions to both surface and situation by exploiting predictions from both methods. Finally, we demonstrate inertial steering on a mono-track vehicle without a conventional steering mechanism, showing that controlled movements of an internal mass can generate turning motion on ice. The resulting behavior can be predicted using the proposed dynamic model by representing the internal mass as a frictionless trailer, revealing the analogous dynamics between the two configurations. These results demonstrate the feasibility of inertial steering as an alternative steering mechanism for tracked vehicles operating in low-adherence environments.

0.21

IMU-Centric Moving Horizon Estimation for Lateral Dynamics Estimation Across Vehicles and Grip Conditions

eess.SY cs.RO ·2026-09-09 ·Seuffo Akouan ha Ngoune, Alessandro Toschi, Paolo Burgio, Marko Bertogna
publishedcode/data similarity 0.57
Abstract · Accepted at the 29th IEEE International Conference on Intelligent Transportation Systems (ITSC 2026). 8 pages, 6 figures

Accurate estimation of lateral vehicle dynamics near the adhesion limit is important for stability control and high-performance driving, but lateral velocity is rarely measured directly because sensors such as optical sensors are costly. This paper presents an inertial measurement unit (IMU)-centric Moving Horizon Estimation framework that reconstructs lateral velocity using standard onboard signals, without relying on exteroceptive odometry or detailed tire-parameter tuning. Experimental validation on human-driven sports cars and an autonomous open-wheel race car across tracks, maneuvers, and conditions demonstrates accurate and robust lateral velocity and lateral acceleration estimates. The proposed framework is available at https://github.com/Aseuffo/IMU-Centric-MHE

0.48

Differentiable Dynamics for Autonomous Micro-Mobility Navigation

cs.RO ·2026-09-25 ·Grace Cai, Joey Lee, Nithin Parepally, Laura Zheng, Ming C. Lin
similarity 0.55
Abstract

Autonomous micro-mobility vehicles (MMVs) such as wheelchairs, scooters, and bicycles have the potential to improve mobility access and support safe low-speed transportation in pedestrian-shared spaces. Achieving MMV autonomy will require realistic, predictable MMV motion. However, many existing autonomous vehicle stacks rely on simplified kinematic models that fail to capture key MMV characteristics such as tire slip, friction, and wheel layouts, limiting realism and gradient-based optimization. In this paper, we explore differentiable formulations of dynamics models for autonomous micro-mobility systems. We first construct DiffKBM, a differentiable version of the kinematic bicycle model (KBM). Then, we introduce DiffGM3, a differentiable formulation of the General Micro-Mobility Model (GM3), a unified tire-based dynamics formulation for micro-mobility vehicles that supports a wide range of MMV configurations. DiffKBM and DiffGM3 enable end-to-end differentiable optimization through MMV dynamics, making them suitable for integration into differentiable autonomy stacks. We evaluate these dynamics models in both open-loop and closed-loop settings: (1) open-loop trajectory matching, where DiffKBM and DiffGM3 are integrated as a dynamics layer within DiffStack and optimized to reproduce real-world MMV trajectories, and (2) closed-loop autonomous navigation, where DiffKBM and DiffGM3 are paired with a differentiable MPC controller in CrowdNav pedestrian scenarios. In the open-loop setting, DiffGM3 outperforms DiffKBM in reproducing trajectories with improvements in ADE and NLL across bicycle, scooter, and motorcycle modes, and reductions in planning loss for bicycle and motorcycle trajectories. We also find that, in closed-loop settings, DiffGM3 improves on DiffKBM's CrowdNav performance by producing 55\% fewer collisions and a 75\% lower discomfort frequency for the bicycle mode.

0.32

Steering Through Contact: A Finite-Support Motion Model for Single-Track Center-Articulated Robots

cs.RO ·2026-09-20 ·Mohamed Dhia Ounally, Nicolas Samson, Mathis Turgeon-Roy, Veronica Vannini, Johann Laconte +1 more
similarity 0.55
Abstract · 8 pages, 7 figures, 1 table

Trajectory planning and control in field robotics rely on predicting how propulsion and steering affect vehicle motion when contact points undergo slip. For articulated vehicles, the point-contact kinematic model (PCK) accounts for the linkage geometry but neglects the rotational resistance distributed along the contacts. We propose a finite-support quadratic model (FSQ) for single-track, center-articulated vehicles that incorporates this resistance through a quasi-static balance of lateral slip. Our approach generalizes the standard PCK formulation by relaxing the contact-point assumption. An exact reduction of the quadratic slip cost to contact moments gives a compact closed-form solution for real-time prediction of lateral velocity and yaw rate. We evaluate the proposed method in real-world experiments across asphalt, grass, ice, and mixed routes, using more than 7 km of data. For five-second predictions, FSQ reduces the weighted median translation and yaw errors by 53.5% and 68.9%, respectively, relative to PCK.

0.29