CS Paper Radar

Intent-guided Adaptive Stiffening for Visuomotor Policies under Unknown Resistance

Francesco Cufino, Carmela Mariniello, Mario Selvaggio, Andreas Sochopoulos, Fabio Ruggiero

cs.RO ·submitted 2026-10-13 13:36 UTC · v1

Abstract

Manipulation tasks such as unscrewing a cap or sliding a part in contact with a surface require imposing force along a high-friction direction: the robot must overcome a resistance rather than yield to it. Generative visuomotor policies predict the motion for such tasks but not the authority needed to realize it, and that authority is bounded by the impedance controller beneath them: when the resistance exceeds what a compliant controller can exert under a bounded tracking error, the task is unattainable however accurate the prediction is. The required amount cannot be anticipated either, since it depends on a contact state the observation does not reveal. In this paper, we propose a residual stiffening layer placed underneath an unmodified policy. Resistance is recognized, without force sensing, from the mismatch between the motion the policy commands and the motion the robot realizes, and a four-mode supervisor raises the stiffness along a single direction read off the policy's own action chunk, retains it while the task progresses and releases it afterwards. The layer needs no compliance labels, no retraining and no re-collected demonstrations. On two real tasks, unscrewing a bottle cap and pushing a T-nut along a T-slot groove against non-homogeneous friction, evaluated at six resistance levels of which two were withheld from the demonstrations, the layer raises the success rate from 52% to 90% while producing 61% less peak off-axis force than a uniformly stiff controller at the same resistance.

Comment
Submitted to ICRA 2027

Closest papers

Nearest neighbours by meaning across the whole index.

Imp-ACT: Adaptive Impedance Control and Action Chunking with Transformers to Learn Contact-Rich Manipulation from Demonstrations

cs.RO ·2026-09-25 ·Luca Zanetti, Doganay Sirintuna, Idil Ozdamar, Pietro Balatti, Heng Zhang +1 more
similarity 0.72
Abstract · 9 pages, 5 figures, submitted to IEEE International Conference on Robotics & Automation 2027, for associated video see https://youtu.be/iAu_…

Contact-rich manipulation requires robots to balance accurate motion tracking with compliant interaction, yet most visual-action policies leave compliance fixed at the controller level. We present Imp-ACT, a methodologically grounded and practical approach to incorporating direction-dependent Cartesian stiffness modulation directly into demonstration collection, without manual stiffness selection or offline target reconstruction. During teleoperation, a self-tuning impedance controller adapts stiffness along the instantaneous direction of motion while maintaining compliance in orthogonal directions. The adapted stiffness is applied and recorded alongside visual observations and motion commands, capturing motion and compliance under the same dynamics. We implement this pipeline using Action Chunking with Transformer (ACT) to predict end-effector pose, gripper action, and motion-direction stiffness from visual, proprioceptive, and wrench observations. The performance of Imp-ACT is evaluated on wiping and plug insertion using both success rate and quantitative measures of contact behavior. Compared with fixed low- and high-stiffness baselines, Imp-ACT achieves comparable or higher success while maintaining low interaction forces. In wiping, it reduces contact-force vibration by approximately $29\times$ relative to the compliant baseline and $180\times$ relative to the stiff baseline. In plug insertion, it reduces forces orthogonal to the insertion direction by $43\%$ relative to the better fixed-stiffness baseline. These results highlight the benefit of maintaining sufficient stiffness along the direction needed for task execution while preserving compliance in other directions to limit contact forces and accommodate environmental constraints.

0.32

Residual Compliant Policy: Learning Compliant Policies from Few Demonstrations

cs.RO ·2026-10-01 ·Chunyu Jiang, Yichen Cai, Shuai Li, Wenbin Sun, João Carvalho +4 more
similarity 0.70
Abstract · 9 pages, 6 figures. Project website: https://residual-compliant-policy.github.io

Contact-rich manipulation requires a robot to be precise in free space to establish the intended contacts, and compliant once in contact to avoid excessive forces. Imitation learning has proven effective for simpler manipulation tasks, but the compliance underlying a demonstration is not directly observable and is therefore difficult to infer from demonstration data alone. We present a framework that makes compliance explicit at every stage. During data collection, the operator teleoperates the real robot while a synchronized digital twin visualizes the error between the commanded reference and the achieved pose, making the current compliance visible, and selects between two discrete compliance modes. To generalize across object poses, we combine Laplacian editing, which retargets trajectories efficiently but is not physics-consistent during contact, with simulation-based trajectory optimization, which enforces physical plausibility but offers no manual guidance. Finally, a residual reinforcement learning policy refines the interaction forces by adjusting the reference pose of the underlying admittance controller. We evaluate on three flipping and pushing tasks on a Franka FR3 based on a total of 7 demonstrations across tasks. Our method is successful on all 40 out-of-distribution trials, compared to 33/40 and 24/40 for two baselines, with our base policy alone reaching 35/40.

0.27

Learning Reflexive Behavior for Contact-Rich Manipulation

cs.RO ·2026-10-02 ·Quan Nguyen, Yunho Kim, Joonho Lee
similarity 0.69
Abstract

During contact-rich manipulation, interactions between a robot and its environment carry information about local geometry: a surface prevents penetration, a bore guides a peg. A controller that exploits these interactions can comply with environmental constraints while preserving task intent. Robot-earning systems commonly use position, hybrid force-position, or Cartesian impedance control. Their prescribed tracking objectives, stiffness, or force-control directions may not match local constraints and may degrade performance. We learn a proprioceptive reflex policy in simulation on three simple interaction primitives: a spring, a plane, and a rail. The policy maps task-space commands to joint-position targets using state history, without direct force or geometrical measurements. Once trained, it serves as a frozen execution layer beneath higher-level controllers. We evaluate it in dual-arm box lifting, peg insertion, and surface following. In box lifting, the reflex kept the force below the threshold while the baseline failed. In rough-surface following it stayed below the 10 N reference, on par with tuned hybrid force-position control. In 0.02 mm peg insertion It reduced mean estimated contact force to less than half that of the baseline while increasing hardware success rates from at most 22 % to 36-58 %. By separating contact response from command generation, the reflex policy provides motion planners, learned policies, and teleoperators with robust contact-rich execution.

0.15

Compliance for Free: Learning Identifiable Impedance via Bilateral Teleoperation

cs.RO ·2026-09-17 ·Harsha Guda, Adrià Colomé, Carme Torras
similarity 0.68
Abstract

Vision-language-action models tell a robot where to move, but not how hard to push. Contact-rich tasks depend on that second quantity, compliance, yet no widely used demonstration interface records it. The obstacle is identifiability as realized pose and measured force cannot separate the operator's intended equilibrium from their stiffness, so VR controllers, SpaceMouse and handheld grippers cannot supply compliance supervision even in principle. Prior compliance-output policies work around this with hand-specified task structure, privileged simulation contact state, or dedicated force and tactile hardware. Four-channel bilateral teleoperation removes the ambiguity directly by using the leader arm as a separate measurement of the intended equilibrium, making per-axis stiffness identifiable by regression using only the joint-torque sensing already on the manipulator. This yields per-timestep, direction-dependent compliance labels at zero annotation cost, which we use to fine-tune a VLA to emit stiffness alongside pose. On a Franka Research 3 wiping task, ours is the only policy of five whose contact force changes when the instruction asks for a firm wipe rather than a normal one (6.4N (normal) to 9.1N (firm) RMS, Cohen's d = 0.89, p = 0.023

0.22

Robot Learning with Visual Predicted Force

cs.RO cs.AI ·2026-10-03 ·Haonan Chen, Feiyang Wu, Yuxiang Ma, Mustafa Mete, Pengfei Ye +9 more
similarity 0.68
Abstract · 9 pages, 8 figures. Project Website: https://visual-force.github.io/

Force-aware manipulation typically relies on specialized force or tactile sensors. We show that force-aware manipulation can instead be achieved through visual force prediction from the deformation of a compliant Fin Ray gripper. Our approach trains two models. First, we train a visual force estimator on calibration data and use it to annotate task demonstrations with force estimates. Second, we train an action--force proposal policy on these force-augmented demonstrations to jointly generate candidate robot actions and their associated forces. At test time, we sample candidate actions and the forces they are expected to produce, then execute the action whose predicted force is closest to a target from the demonstrations. We evaluate our approach on berry picking, empty-can grasping, in-hand reorientation, and plug insertion. Our results show that visual force prediction can guide inference-time action selection for contact-rich manipulation without requiring force or tactile sensors at deployment.

0.25

CEER2: Directional and Tunable End-Effector and Root Compliance for Humanoid Loco-Manipulation

cs.RO ·2026-09-30 ·Xinyuan Luo, Chunyuan Yang, Boyuan Chen, Xianyi Cheng
similarity 0.68
Abstract · 8 Pages, 5 figures

Humanoids are increasingly capable of tracking complex whole-body motions, but physical interaction introduces a different challenge. When a robot makes contact with a person or the environment, it needs to respond to external forces while preserving the motion needed for the task. This response can vary across directions in the end-effectors and on the body. For example, an end effector may need to accommodate contact force in one direction while maintaining motion accuracy in another, while the robot body may resist an external force or move with it. We present a compliance framework for humanoid loco-manipulation that combines directional and tunable end-effector (EE) compliance with selectable root compliance for external force rejection or force following. A hierarchical reinforcement learning controller modulates a fixed whole-body tracking policy through high-level EE and root commands, while interaction forces are estimated from proprioceptive history. Our simulation and real-world experiments on a humanoid demonstrate directional stiffness control, online stiffness adjustment, distinct root compliance, compliant manipulation, and collaborative carrying.

0.20

CompliantBot: Learning Whole-Body Compliance across Task Interfaces for Humanoid Control

cs.RO ·2026-11-01 ·Haoyang Li, Keqi Zhu, Zhanxiang Cao, Yang Zhang, Yizhi Chen +2 more
similarity 0.67
Abstract · 12 pages, 8 figures, 5 tables

Humanoid controllers need the ability to yield to external forces while retaining the capacity to resume their original tasks. However, tracking objectives penalize the deviations needed for yielding, while relaxing tracking goals persistently can make task recovery harder. Existing approaches often rely on task-specific interaction command interfaces or constructed compliant motion data and reference trajectories, limiting the direct reuse of their compliance-training mechanisms across different task interfaces. We introduce CompliantBot, a compliance-training framework for motion tracking and velocity-command locomotion. It preserves the original task inputs and requires no preconstructed compliant data or target trajectories. A state-dependent interaction force field couples applied loads to the robot's motion, enabling local articulation and whole-body movement to change the forces experienced. A complementary force-magnitude reward encourages lower interaction loads, while task rewards are downweighted during loading and restored after release to coordinate yielding and task resumption. The trained policies use task inputs and proprioceptive history without explicit external-force measurements. Across both task interfaces, CompliantBot yields farther under constant pulls and experiences lower spring interaction loads than matched baselines, while resuming task tracking after force removal. CompliantBot achieves the highest task completion among the compared methods under stronger pulls. Power evaluations further show that CompliantBot has the lowest mean joint mechanical power among the compared methods. Real-robot demonstrations further illustrate compliant responses through arm motion, stepping, and body reorientation.

0.23

ImpedanceMimic: Learned Impedance as Action Space for Force-Accurate Motion Imitation

cs.RO cs.GRcs.LG ·2026-11-14 ·Matthias Jammot, Pembe Gizem Özdil
code/data similarity 0.67
Abstract · 39 pages, 13 figures, 28 tables. Project page: https://impedancemimic.github.io/ImpedanceMimic/

Recovering the forces behind a motion is ill-posed: different controllers can reproduce the same movement while generating different contact forces. Physics-based motion imitation resolves this ambiguity through simulation, but relies on fixed-gain proportional-derivative (PD) control. We show that fixed gains impose a trade-off between motion and force tracking, as contact and swing place conflicting demands on joint stiffness and damping. We introduce ImpedanceMimic, a reinforcement-learning policy that modulates per-joint stiffness, damping, and position setpoints from motion and force measurements, but requires only motion at inference. Across 129 participants and six activities, ImpedanceMimic outperforms matched fixed-gain PD under every integration scheme, direct-torque, muscle-actuated and existing imitation controllers in kinematic and force fidelity, approaching a dedicated motion-to-force regressor. By expressing gains as multiples of inertia-scaled priors, a single policy controls subject-specific biomechanical models without explicit anthropometric input and transfers zero-shot to unseen humans and a humanoid robot. The learned impedance forms a low-dimensional representation of motor state, shared across bodies, that generalizes to withheld activities: stiffness scales with load, and damping anticipates unloading.

0.22