CS Paper Radar

Attribution-Gated Joint Estimation of Intention and Capability for Assist-as-Needed Upper-Limb Robots

Pengcheng Li, Shuxiang Guo, Hanze Wang, Jun Leng, Bin Wang, Mingchao Ding

cs.RO ·submitted 2026-10-15 09:02 UTC · v1

Abstract

Assist-as-needed (AAN) control must distinguish between changes in intended motion and changes in effective voluntary torque capability, even though both can produce similar kinematic and interaction responses. A dual-measurand multimodal MHE-MPC architecture is developed as the base framework, in which the intended trajectory and the task-dependent effective voluntary torque capability are estimated online as distinct quantities, and both estimates are used to adapt robotic assistance. Building on this architecture, the ambiguity between the two update channels is formulated as a continuous credit-assignment problem and resolved by an attribution gate. A trajectory-change indicator is obtained from persistent corrective interaction, whereas a capability-change indicator is derived from the residual between normalized muscle activation and dynamics-reconstructed voluntary torque. Nine healthy participants completed factorial target-height-load trials and a pre-post fatigue cup-transport task. Without target-height input, the gated method generated correctly ordered Low-Middle-High references under every load: target changes were preferentially assigned to trajectory adaptation, whereas added load shifted adaptation toward the capability channel. It achieved the lowest RMSE in all nine conditions (0.017 rad versus 0.041 rad for ungated dual estimation and 0.127 rad for fixed-reference error-based AAN). Post-fatigue capability estimates decreased and assistance increased at all heights, supporting functional feasibility.

Comment
31 pages, 7 figures

Closest papers

Nearest neighbours by meaning across the whole index.

General Performance Guarantee for Human Torque Estimation-Based Task-Agnostic Assistive Exoskeleton Control

cs.RO cs.LGeess.SY ·2026-09-30 ·Duy Hoang, Bastien Berret, Olivier Bruneau, Laurent Fribourg
theory similarity 0.64
Abstract · 10 pages, 8 figures

Accurate human torque estimation is crucial for enabling task-agnostic control in robotic exoskeleton systems. However, estimation errors may cause mismatches between the robot assistance and the human intention, degrading controllability and task performance. In this paper, we address this issue by formally defining matched assistance as scenarios in which the robot positively contributes to human movement. Based on this definition, we develop a theoretical framework to design the robot's desired interaction torque that guarantees a lower bound on the matched assistance probability. Importantly, the proposed guarantee holds over the entire torque distribution, including unseen data beyond the training tasks. This provides our method with strong reliability and generalization, both of which are critical for effective exoskeleton control. The proposed strategy is implemented on the ABLE upper-limb exoskeleton and evaluated in a multi-task setup. Experimental results validate the theoretical guarantees and demonstrate that the proposed strategy achieves effective general performance across several tasks, guaranteeing movement smoothness while reducing human physical effort.

0.19

A Flow-Theoretic Multimodal Control Framework Fusing Mental and Physical Engagement for Upper-Limb Rehabilitation

cs.RO ·2026-10-15 ·Jun Leng, Pengcheng Li, Hanze Wang, Shuxiang Guo, Junlin Jiang
similarity 0.62
Abstract · 10 pages

While Assist-as-Needed (AAN) control aims to maximize user participation in robot-assisted training, existing methods relying solely on physical metrics cannot distinguish muscular inability from mental disengagement, leading to suboptimal interventions. To address this ambiguity, a Flow-theoretic multimodal AAN framework is proposed, fusing EEG-based mental engagement and sEMG-based physical engagement into an adaptive impedance control strategy. A four-quadrant fuzzy decision engine translates these dual physiological metrics into continuous control policies. This enables the upper-limb exoskeleton to inject feedforward assistance during intent-execution mismatch (e.g., motor output attenuation despite mental focus) and escalate guiding stiffness to penalize mental distraction. The framework was validated with healthy participants against a state-of-practice sEMG-only AAN baseline. Kinematically and mechanically, the proposed framework reduced robotic energy expenditure by 71.9\% while maintaining precise trajectory tracking, confirming it elicited greater voluntary human effort. Physiologically, the system increased the time spent in the neuroplasticity zone (Flow State Ratio) from 4.6% to 42.8%. These results validate that decoupling and jointly regulating mental and physical states enhances the selectivity of robotic assistance, mitigating user passivity and sustaining the engagement crucial for motor learning.

0.27

A Human-in-the-Loop Comparison of Proportional Control and Adaptive Gravity Compensation in Elbow EMG-Driven Exoskeletons

cs.RO ·2026-10-19 ·Francesco Pascucci, Eldison Dimo, Davide Costanzi, Mario Sedilesu, Andrea Calanca
similarity 0.62
Abstract · 8 pages, 10 figures, 4 tables

Electromyography (EMG)-driven control enables wearable robots to assist users based on their neuromuscular activity. Upper-limb exoskeletons typically rely on proportional myoelectric control (PMC), which amplifies user effort but may compromise stability at high assistance levels. EMG-driven adaptive gravity compensation (AGC) offers a promising alternative, counterbalancing gravitational torques while continuously adapting to neuromuscular activity. However, these approaches have not been systematically compared in a human-in-the-loop setting. This study evaluates five control algorithms: two PMC strategies at different assistance levels, a purely integral AGC (AGC-PI), a kinematics- and acceleration-aware model-based (MB) AGC (AGC-AW), and a novel MB AGC approach based on Recursive Least Squares (AGC-RLS) for online payload estimation. Fourteen healthy participants performed target-reaching tasks using an active elbow exoskeleton under 0 kg and 2 kg loading conditions. Performance metrics included muscular activity, movement accuracy, task efficiency, and subjective workload. PMC exhibited a trade-off between physical effort and task performance: low assistance levels required greater physical effort under load, whereas high gains impaired task execution. AGC-PI reduced agonist activity but induced antagonist activation. In contrast, both model-based AGC approaches effectively compensated for external payloads, reducing physical and cognitive demands while improving movement accuracy and completion time.

0.20

Learning Functional Specialisation for Bimanual Robotic Control

cs.RO ·2026-10-24 ·Jingwen Li, Levin Kuhlmann, Jason Friedman, Gideon Kowadlo
similarity 0.60
Abstract · 24 pages, 6 figures, 10 tables

Bimanual robotic control requires simultaneous management of distinct functional demands under motor noise, energetic costs, and communication delays. We investigate how learning responsibility should be organised across modular controllers and the two arms in a simulated musculoskeletal system with two communicating recurrent controllers. Using a 2 x 2 design, we compare differential versus shared controller objectives and fixed versus balanced hand-task assignments. Task-aligned functional specialisation was strongest when differential objectives were combined with a fixed assignment aligned with contralateral control routing. This condition achieved the highest canonical-task performance and control efficiency, reaching 81.33% bimanual success. Its advantage over shared objectives increased with motor noise but narrowed under stronger energy penalties. Stronger specialisation also reduced hand-role flexibility: reversing the hand roles decreased bimanual success by 80.46 percentage points under Differential-Fixed training, compared with 1.51 percentage points under Shared-Balanced training. These results show that controller objectives and hand-task experience jointly determine functional organisation. Stronger role-specific specialisation favours performance and efficiency when roles remain stable, whereas more distributed training favours interchangeability when roles change.

0.15

Whole-Body Motion Guided Reference Generation for Uncertainty-Aware Compliant Assistance

cs.RO ·2026-10-22 ·Muyuan Ma, Long Cheng, Lijun Han, Haotian Zhai, Xinpan Meng +3 more
similarity 0.60
Abstract · Withdrawal requested because not all co-authors had consented to the submission of this manuscript to arXiv

Exoskeletons have shown great potential for augmenting human physical capabilities, yet generating reliable assistance remains challenging because human motion patterns and interaction requirements vary substantially in practice. To address this problem, a dual-loop assistance strategy is proposed to couple multimodal exoskeleton trajectory generation with variable admittance control, where trajectory variance links the outer-loop generator and the inner-loop controller. The generator synthesizes future exoskeleton trajectories through denoising, primarily using whole-body human motion and exoskeleton proprioception, with task descriptions as auxiliary semantic cues. To reduce cross-modal representation mismatch, a three-stage training pipeline is introduced to progressively optimize the human motion encoder, the exoskeleton proprioception encoder, and the trajectory generator. In the inner loop, multiple future trajectories are sampled from the generator to estimate the trajectory mean and variance. The mean is used as the control reference, while the variance provides an uncertainty measure for prediction reliability. This measure is further incorporated into a stiffness regulation law, enabling compliant assistance with input-to-state stability under bounded lumped interaction input. Experimental results demonstrate that the proposed method significantly reduces muscle activation levels compared with standard baselines, while also decreasing users' metabolic energy expenditure relative to the unassisted condition.

0.21

An Empirical Study of Wrist-Target Construction and Joint-Angle Limits in Humanoid Arm Retargeting

cs.RO ·2026-10-27 ·MinJun Chang
similarity 0.60
Abstract · Submitted to ICRA2027 under process

Motion retargeting maps a demonstrated human movement onto a robot to compute its joint motion. This study examines how the construction of the desired wrist position affects whether computed arm joint angles reach their permitted limits on a Unitree H1-2. A reconstructed target is formed from demonstrated arm directions and robot segment lengths, so its shoulder-to-wrist distance depends on the demonstrated angle between the segments even when no posture-matching preference is applied. A reach-normalized target retains that direction while rescaling the distance, using the same processed demonstrations and the same joint-angle method. Across a forward-reach sweep the reconstructed target places a joint angle at a bound in 10 of 20 repetitions and the reach-normalized target in none. Across 25 recordings from one participant the corresponding counts are 8 and 6 on the reaching arm and 14 and 5 on the supporting arm, and a second participant repeats the bricklaying and lifting comparison. In hardware replay a joint is commanded to a bound in 12 of 16 direction-matching arm-records and in none of the 16 normalized records, and within the eligible records both tracking error and executed torque at those frames exceed their values elsewhere in the same run. Cross-body reach and arm-to-arm clearance identify limits of radial adjustment. The findings support treating target construction and posture matching as separate retargeting decisions, and evaluating both alongside the wrist positions and clearance that manipulation requires.

0.11

Recursive Self-Improvement of Exoskeleton Assistance Policies through Human-in-the-Loop Feedback

cs.RO ·2026-11-01 ·Muyuan Ma, Shuo Jiang, Lijun Han, Xinpan Meng, Zhenghua Ma +3 more
hot direction similarity 0.59
Abstract

To reduce reliance on manual design and extensive parameter tuning, a framework for the autonomous evolution of exoskeleton assistance policies through human feedback is proposed. Assistance policies are autonomously generated as executable control code by an intelligent agent and evaluated in experiments with human participants. Subjective user feedback, movement performance, and muscle activation measurements are incorporated into policy assessment. Based on these assessments, policy deficiencies are autonomously identified and the control code is revised by the agent for subsequent trials. A closed loop of policy generation, human feedback, evaluation, and autonomous refinement is thereby established. The framework is evaluated using GPT, DeepSeek, GLM, and Kimi, and initial assistance performance and refinement outcomes are compared across models. Despite differences in initial performance, effective assistance is achieved with all four models after a single autonomous refinement iteration under the tested conditions. Across three tasks, biceps and triceps muscle activation levels are reduced by 29.4% and 35.2%, respectively, compared with those measured without an exoskeleton. However, limited adaptability to unexpected situations is observed, indicating that further improvements in robustness and safety are required.

0.30

Design and Control of a Cable-Driven Switchable Actuator with Torque/Tension Dual Modes for Exoskeletons

cs.RO eess.SY ·2026-09-20 ·YuanLong Ji, Xu Liu, Xinyuan Cai, Qihan Ye, Xiangyu Xie +6 more
top venue similarity 0.59
Abstract

Existing wearable exoskeleton architectures are typically constrained by a single mechanical output modality, providing either joint torque around an anatomical joint or linear traction along a limb-training-oriented direction, which limits adaptability to diverse training scenarios. This letter presents a cable-driven switchable actuator (CDSA) that can rapidly switch between torque and tension modes while centralizing all sensing and actuation components at the proximal drive unit. A Coupled Movable Pulley Mechanism (CMPM) provides tension amplification at the distal end-effector, while a bidirectional Cable-Driven Ratchet Mechanism (CDRM) enables mode switching and preload regulation. To eliminate the need for distal instrumentation, multi-source proximal sensors are integrated with a data-driven fusion model to estimate distal output forces. An adaptive dual-mode force control strategy based on iterative learning control (ILC) is further developed. Platform experiments demonstrate transmission efficiencies of $(92.4 \pm 2.0)\%$ and $(96.5 \pm 3.3)\%$ in the torque and tension modes, respectively, along with a tension amplification ratio of $2.77 \pm 0.10$ under tension mode. Tracking tests on simulated knee-joint gait trajectories and short-stroke tension profiles yield stable control, with RMSEs of $(4.52 \pm 0.51)\%$ and $(3.15 \pm 0.19)\%$ of the uncontrolled peak value, respectively. Finally, seated human-coupled experiments validate the system's controllable force generation in both joint-torque and linear-traction application modes.

0.40