CS Paper Radar

Binder migration across film consolidation and pore emptying in electrode drying: a continuous model validated against drying-rate, thickness, and schedule experiments

Younghwan Joo, Sanghyun Oh, Sung-il Kim

cs.CE cond-mat.mtrl-sciphysics.app-ph ·submitted 2026-10-21 06:37 UTC · v1
unusual

Abstract

Drying battery electrodes faster saves energy but drives dissolved binder toward the film surface, depleting the current-collector interface and weakening adhesion. Models of this migration stop convecting the binder when film consolidation ends, and models of the subsequent pore emptying omit the binder or start from an assumed binder field, so no simulation has followed binder convection through both stages that a drying schedule acts on. This study presents a continuous simulation of the dissolved binder field across both stages, driven by the published drying rates and completed by effective descriptions of the two questions the base transport physics leaves open: where the liquid of the consolidating film carries the binder, and when the binder stops moving as the pores empty. With a single parameter set, the simulation reproduces three types of published measurements: the change of the surface-to-interface binder ratio with drying rate over a factor of 5.6 and the surface and interface binder levels of films six times thicker; concentration profiles through the film interior; and the response of the interface binder to the time at which the drying rate is switched mid-process. Applied without further adjustment to a published three-stage schedule, the model reproduces the shortened drying and the full interface recovery when the rate is lowered early, and shows that its final high-rate stage begins after the binder has stopped. Combined with a coater-scale process model, the model can be used to identify operating points for electrode production that improve energy efficiency and product quality together.

Comment
48 pages, 10 figures, 4 tables. Submitted to Applied Thermal Engineering. Data: https://doi.org/10.6084/m9.figshare.34704411

Closest papers

Nearest neighbours by meaning across the whole index.

A dynamic pore-network model with discrete microbubble transport

cs.CE physics.flu-dyn ·2026-10-07 ·Kristoffer Skjelanger, Anna Mareike Kostelecky, Maziar Veyskarami, Timo Koch
unusual similarity 0.41
Abstract · 32 pages (+11 in supplementary) and 20 figures (+18 in supplementary)

We develop a hybrid pore-network model (PNM) for discrete microbubble transport coupled to connected two-phase flow in porous media. We apply the model to simulate flow in the porous transport layer of a rotating proton exchange membrane (PEM) electrolyser. At sufficiently large apparent gravitational forces, bubbles growing at the catalyst layer can detach at sizes smaller than the characteristic pore size and move through liquid-filled pores via buoyancy and advection. The model couples a dynamic two-phase PNM to a Lagrangian bubble tracker. Pore-scale Stokes simulations in square throats provide closures for the bubble buoyancy velocity, the hydraulic resistance of bubble-occupied throats, and the reciprocal coupling between liquid flow and bubble motion. Verification tests assess conservation, pressure-flow coupling, bubble growth, advection, merging, trapping, and transfer to the connected gas phase. The network simulations show that increasing apparent gravitational forces shifts a larger fraction of the produced gas toward discrete-bubble transport. The increase mostly comes from a reduced detachment radius, which decreases bubble size and lets them move more freely through the network.

0.33

Integrated Population Balance and Multiphysics Modeling for Predicting Undesired Agglomeration in Small Molecule Manufacturing

cs.CE cond-mat.otherphysics.comp-ph ·2026-09-09 ·Prakitr Srisuma, Peter Hou, Shashank Venkat Muddu, Neda Nazemifard, Allan S. Myerson +1 more
unusual similarity 0.40
Abstract

Agitated filter dryers (AFDs) are a crucial unit operation in small molecule manufacturing that enables simultaneous filtration, washing, and drying of active pharmaceutical ingredients. One of the key challenges in AFDs is associated with undesired agglomeration, where the presence of hard agglomerates results in off-spec products, equipment damage, and additional downstream processing. This article presents a novel mechanistic model that describes the formation of soft and hard agglomerates during agitated filter drying. By integrating population balance and multiphysics modeling, the model can accurately predict the evolution of the product temperature, moisture content, and particle size distribution, and hence quantify the extend and impact of undesired agglomeration across various operating conditions. Our proposed model-based framework enables the rational design and operation of AFDs for improving the product quality and process reliability.

0.28

Robotic Multiphase Interaction: Manipulating Coupled Liquid and Solid Dynamics with a World Model

cs.RO ·2026-09-18 ·Yixuan Feng, Peng Wang
similarity 0.36
Abstract · 11 pages, 6 figures, 6 tables

This work presents \textit{Robotic Multiphase Interaction (RMI)}, a setting in which liquid enters a porous material and interacts mechanically with its deforming solid skeleton. Manipulation can therefore change pore volume, expel or redistribute retained liquid, and alter grasp stability at the same time. Spilled liquid can also create safety risks in domestic and manufacturing settings. This differs from most manipulation of solid objects and from tasks that involve both liquid and solid while keeping the phases spatially separate. We study a sponge filled with water as the first RMI example. We use implicit incompressible porous flow with smoothed particle hydrodynamics as the dynamics engine and enable robotic manipulation by adding Coulomb contact memory, hybrid velocity and force regulation, and a stability gate for lifting. The resulting environment connects robot commands to changes in the coupled liquid and solid state. A world model conditioned on actions predicts how this state evolves under candidate commands, while a temporal UNet generates actions using either Diffusion Policy or rectified flow matching. Our world model reduces retained water prediction error by more than $60\%$ compared with the baseline. The best action sequence selected by the world model from policy proposals further reduces the predicted terminal water error by about half. These improvements show that modelling the coupled liquid and solid state helps the robot predict how its actions affect both the porous object and the liquid held inside.

0.31

Parameterisation of NMC and LFP 4680 cells for electrochemical and thermal modelling

eess.SY cs.CEphysics.chem-ph ·2026-11-01 ·Remus Teodorescu, Nicolai A. Weinreich, Berke Bilgin, Yi Zhuang, Wenzel Prochazka
code/dataunusual similarity 0.36
Abstract · 36 pages, 6 figures, 4 tables; supplementary material included. Submitted to Frontiers in Batteries and Electrochemistry. Data: https://gith…

An electrochemical-thermal model of the 4680 cylindrical cell is presented: a Doyle-Fuller-Newman model of the electrode stack coupled to a two-node thermal balance of the roll and the can (a thermal DFN, TDFN), solved by an implicit finite-volume scheme. Two cells are parameterised from teardown geometry and open literature, with every value tagged by provenance: the Tesla NMC811/graphite tabless cell and the BYD FC4680 LiFePO4 multi-tab cell. The reaction heat is evaluated at the open-circuit potential of the particle-mean concentration, which restores the heat of mixing. Both sets are calibrated in the same way, with the test fixture identified from the measurement alone. Against the 1C and 2C charge test of Ank et al., the calibrated NMC set follows the mean can temperature within 0.52 and 1.46 K, with a contact heat of 0.94 mOhm matching the authors' estimate for their holder. For the LFP cell, 1C and 2C discharges to 2.0 V were measured on the authors' bench; the fixture conductance (0.337 W/K) follows from the energy balance and the heat capacity (277 J/K) from the cooling. With the end-of-lithiation drop of LiFePO4 restored in the cathode open-circuit potential, the calibrated set follows the can temperature within 0.44 K (1C) and 0.76 K (2C), reproduces the peaks and the relaxation after cut-off. What remains is what a single can node and a single representative particle do not describe: the axial gradient of the NMC can under contact heating, and a gradual decline of the LFP voltage before the knee at 2C, which points to the distribution of particle states in the electrode. The parameter sets (BPX, CSV) and the bench data are openly available.

0.47

Optimal Control and Closed-Loop Stability of Droplet Transport in a Microchannel

eess.SY math.OCphysics.flu-dyn ·2026-09-16 ·Rajneesh Anand, Mayuresh V. Kothare
code/data similarity 0.36
Abstract · 35 pages, 9 figures, The complete source code for the ODEs, PDEs, and detailed finite element implementations will be released at https://gi…

Understanding the efficient transport of fluid droplets in confined geometries has been a domain of interest for industrial applications in recent times. In the present work, we focus on designing control strategies that optimally steer droplet motion. Here, we apply optimal control framework to the droplet transport problem in a microchannel based on lubrication theory that minimizes viscous dissipation. Two complementary modeling routes are adopted: a reduced-order ordinary differential equation (ODE) model optimized via Pontryagin's Maximum Principle, and a full nonlinear partial differential equation (PDE) model optimized using a Covariance Matrix Adaptation-Evolutionary Strategy. By parameterizing target displacement, droplet size, and capillary number, we uncover two distinct optimal transport regimes: a "translate-relax" strategy for short distances and a "compact-translate-relax" strategy for longer targets. In continuum mechanics, the competition between surface forces and cumulative viscous dissipation decides the optimal transport strategies. We further show that the displacement range over which the reduced-order controller transfers to the continuum model is governed by capillary stiffness. We finally address closed-loop stability by adapting a control Lyapunov function (CLF) framework to the reduced-order dynamics. We demonstrate that the terminal cost which penalizes deviation from the target, serves as a cost-compatible CLF on the physical domain, and prove that the CLF-compatible feedback exponentially stabilizes the target state.

0.42

Battery Second Life : A Review of Experimental Studies

eess.SY ·2026-10-08 ·Marwan Hassini, Eduardo Redondo-Iglesias, Pascal Venet
survey similarity 0.33
Abstract

As electric vehicle volume increase, the interest for reusing their retired batteries grow. Giving a second life to batteries reduce their environmental impact and provide access to more affordable energy storage systems. This lifespan extension is of interest in a wide range of fields as the reuse offer a solution for end-of-life batteries management and the development of renewable energies. Although several review articles have described opportunities and barriers related to reuse, to our knowledge none have synthesized insights from studies that conducted experiments on retired batteries. This article aims to address this gap by providing a detailed analysis of more than 150 articles. This article's main findings are the proposition of a new vocabulary for batteries end-of-life, an evaluation of state of health and dispersion in retired batteries as well as the synthesis of aging and safety studies on these batteries. In a nutshell, this review show that the performance of retired batteries can be high, their dispersion should be managed and their degradation can be slow and safe. Limitations of current battery research ideas for future experiments and ideas for future studies are also presented.

0.20

The conductance filtration: sink-relative persistence and exact edge sensitivity for heat transport in particle-filled composites

cs.CE cond-mat.mtrl-scicond-mat.dis-nn ·2026-09-25 ·Daisuke Yasufuku
unusual similarity 0.33
Abstract · 45 pages, 15 figures. Japanese-language version: https://doi.org/10.5281/zenodo.22760047

We formulate the thermal conductance $g_e$ of a particle pair as three branch types -- contact, near-contact and bond -- within a single construction, and we introduce the filtration that takes this $g_e$ as its axis (the conductance filtration) together with persistence taken relative to the sink boundary. We then show that the dissipation share is exactly the logarithmic sensitivity of the effective conductance, and that a finite change of a single edge is predicted exactly in closed form. The allocation of the dissipation among branch types, and the idealisation ratio of each mechanism (interface, matrix and particle), are thereby obtained as diagnostic quantities on one and the same graph representation.

0.41

A unified and composable framework for modeling packed-bed liquid chromatography

cs.CE q-bio.OT ·2026-10-23 ·Jan Michael Breuer, Samuel Leweke, Johannes Schmölder, Antonia Berger, Gregor J. Gassner +1 more
unusual similarity 0.33
Abstract

Packed-bed chromatography is a cornerstone of bioseparation, yet its modeling landscape remains fragmented by numerous model variants, inconsistent terminology, and limited structural clarity. While prior work has categorized and contrasted individual variants, our approach shifts the focus to unification. We present a unified, modular, and composable framework that integrates diverse mechanistic packed-bed chromatography models into a coherent structure. Starting from a high-resolution three-dimensional model, the framework systematically derives a hierarchy of reduced-order models through formal model order reduction. It encompasses a broad range of bulk transport phenomena, intraparticle mass transfer processes, binding mechanisms, and chemical reactions. Formulated orthogonally, these modules are independently meaningful and can be systematically combined into mathematically consistent models tailored to specific applications. The framework recovers and generalizes existing models, establishes a consistent taxonomy, and enables novel model combinations and extensions, including alternative column and particle geometries, particle-size and particle-type distributions, component-specific pore accessibility, rapid-equilibrium binding and reaction formulations, and size-exclusion with simultaneous binding. The framework is accessible through CADET-Equations, an interactive web application for model assembly and automatic generation of governing equations in LaTeX, promoting standardization and transparency. Its design principles are increasingly reflected throughout the CADET ecosystem, whose modular architecture supports the majority of the proposed model family. The generality and composable design of the framework provide a foundation for extending chromatography modeling software toward integrated bioseparation processes and advanced computational biotechnology applications.

0.27