CS Paper Radar

A Bi-level Co-design Framework for Lunar Monoped with 2D Jump and Landing Control

Sanjay Ramkumar, Suraj Kumar

cs.RO eess.SY ·submitted 2026-10-27 13:20 UTC · v1

Abstract

Legged robots for lunar exploration must be designed for low gravity, where reduced contact forces and long flight phases make leg morphology and controller choice interdependent. We study this for a planar monoped in lunar gravity ($1.625$ m/s$^2$) using a bi-level co-design framework: a differential evolution outer loop searches over link lengths, and each candidate is evaluated on a vertical jump by either a quadratic program based task-space controller (QP-TSC) or a direct-collocation based trajectory optimization. The two controllers yield different optimal link lengths, and trajectory optimization outperforms the QP-TSC across most of the design space, with 17% lower Cost of Transport (COT) at their respective optima. We then extend to a 2D jump, where trajectory optimization with centroidal angular momentum regulation produces stable in-place and forward jumps, and an LQR controller absorbs impact and stabilizes the robot after touchdown. This is demonstrated on a baseline morphology with both links 0.3 m long.

Comment
8 pages, 13 figures

Closest papers

Nearest neighbours by meaning across the whole index.

End-to-End Reinforcement Learning for Quadrupedal Jumping in Lunar Gravity

cs.RO ·2026-10-21 ·Levin Müller, Oliver Fischer, Marco Trentini, Yusuke Tanaka, Marco Hutter
similarity 0.71
Abstract

Legged robots can extend planetary exploration to rugged and discontinuous terrain that is inaccessible to conventional rovers. In lunar gravity, jumping further expands this mobility by enabling robots to cross obstacles and gaps that cannot be traversed by walking alone. We present a multistage reinforcement-learning approach that produces a single end-to-end control policy for commanded point-to-point jumping under lunar gravity. The resulting policy has a simple architecture and relies exclusively on mission-compatible onboard sensing, making its deployment on a real lunar mission plausible. In simulation, the learned policy performs accurate point-to-point jumps with landing errors smaller than the robot's body size. We analyze the torque and power demands of lunar jumping and characterize performance degradation under extreme outlier events, including control-update freezes of up to \SI{1}{s} during flight. Hardware transfer demonstrates that the policy can successfully execute a vertical jump under lunar-gravity offloading. Furthermore, the measured torque and power profiles are consistent with the simulation results and remain within the robot's hardware limits.

0.12

LEAP: Gradient Flow Augmented Lagrangian Trajectory Optimization for Contact Constrained Robots

cs.RO ·2026-10-14 ·César E. Ramos Chuquiure, Ryan Tsai, Yutong Zhou, Zihang Huang, Vansh Thakur +6 more
similarity 0.67
Abstract

Generating dynamically feasible motions for legged and manipulating robots requires solving a large, nonlinear, non-convex optimal control problem (OCP) in which contact wrenches must satisfy friction-cone constraints throughout the motion, not only at isolated instants. Existing solvers are sensitive to the initial guess and scale poorly with the number of joints. This paper introduces LEAP, which transcribes the OCP with pseudospectral collocation and, instead of a Newton or SQP solve, integrates a primal--dual gradient flow of a Powell--Hestenes--Rockafellar augmented Lagrangian to compute a solution. Because the flow is stiff, this paper designs a linearly implicit integrator with a Gauss--Newton metric, momentum, and a merit-based step controller that keeps the augmented Lagrangian monotone. Across locomotion benchmarks on five robot platforms, from planar hoppers to 32-joint humanoids, LEAP is the only method to solve every tested problem, achieves substantial speedups over Crocoddyl and Aligator on several benchmarks, and reaches trackable references at smaller compute budgets. The resulting trajectories are validated by tracking them in a high-fidelity simulator and on hardware. We will make the code public upon final acceptance of this paper.

0.24

Learning Safety-Constrained Whole-Body Loco-Manipulation for Lunar Surface Operations

cs.RO ·2026-10-11 ·Alvaro Belmonte-Baeza, Miguel Cazorla, Gabriel J. García, Carlos J. Pérez-Del-Pulgar, Jorge Pomares
similarity 0.66
Abstract · 22 pages. Currently under review in a Elsevier scientific journal

Robotic systems for lunar surface operations must act autonomously and preserve their own integrity in an environment where failures are unrecoverable and continuous supervision is impossible. This paper presents a Constrained Reinforcement Learning framework for quadrupedal mobile manipulators that learns a single whole-body policy for tracking a 6D end-effector pose specified in task space, with operational limits enforced during learning through a constrained learning mechanism. We introduce a reward formulation in which the transition between locomotion and manipulation emerges from the reward geometry rather than from an explicit gating mechanism, a stability term derived from the Gravito-Inertial Inclination Margin and motivated by the reduced-gravity dynamics of the lunar surface, and a design rule for reward regularization that follows from the multiplicative structure of the termination-based objective. The framework is evaluated in a lunar-analog simulation spanning three terrain morphologies at five difficulty levels under lunar gravity, with regolith contact properties calibrated to the JSC-1a simulant and varied from loose to dense. The learned policy attains mean position and orientation errors of 3.22 cm and 6.83 deg. under nominal conditions, retains this precision across regolith densities and over the operationally representative range of terrain difficulty, and reduces soft-constraint violation time by up to an order of magnitude relative to an unconstrained baseline while incurring no hard-constraint violations.

0.51

Co-design of trajectory and morphology for a vertical jump-climbing robot

cs.RO ·2026-09-25 ·Christopher Y. Xu, Elliot W. Hawkes
similarity 0.66
Abstract · 8 pages

Animals such as squirrels and even bears have adapted to rapidly climb up trees and other complex vertical terrain, but achieving comparable agility has been a challenge for climbing robots. Existing robots often use walking gaits and move conservatively to stay in contact with the surface, which limits the range of dynamic maneuvers. In this paper we present a 290 g robot that, to our knowledge, is the first to climb vertically by bounding (with an aerial phase). We leverage a co-design workflow, in which the morphology and trajectory are jointly optimized for fast locomotion, subject to adhesion force limitations seen in spined grippers. The resulting trajectory includes a rapid maneuver that launches the robot vertically, and an aerial reorientation that brings the front grippers back to the surface using the rear leg as an inertial tail. We evaluate the resulting jump forces in 2D force space and demonstrate that the optimized morphology is capable of continuous climbing at a speed of 0.375 m/s (1.97 body lengths/s), and can also achieve ground locomotion and transition to a vertical surface. Our work proposes design insights for the jump-climbing maneuver and serves as an important step toward creating climbing robots with agility on par with that of animals.

0.34

Design and Control of a Multimodal Legged-Aerial Robot Through Separate Control Contraction Metrics

cs.RO eess.SY ·2026-10-19 ·Kaushik Venkatesh Krishnamurthy, Eric Sihite, Alireza Ramezani, Morteza Gharib
published similarity 0.65
Abstract · Presented at 2026 IEEE International Conference on Intelligent Robots and Systems, Pittsburgh PA

The integration of dynamic legged locomotion and aerial mobility offers versatility that is deterred by challenges in payload distribution, actuation, and the contrasting requirements of both domains. In this paper, we present the design and operation of a multimodal quadrupedal aerial-legged robot. The presence of legged aerial systems also allows for thruster-assisted legged locomotion, which we make possible with a unified control framework using Control Contraction Metrics (CCM). We search for separate domain-specific contraction metrics for walking and flight independently offline and unify them using an online energy-based Control Lyapunov Function Quadratic Program (CLF QP). This enables optimal, cross-domain control allocation, which we show using simulations. We also show experimental results that validate the mechanical viability of our hardware and the paradigm of thruster-assisted trotting. The stability of said experiments motivates the deployment of the control framework for multimodal operations.

0.20

DR-MPC: Fast and Feasible Dynamics-Relaxed Model-Predictive Control for Legged Locomotion

cs.RO eess.SY ·2026-09-17 ·Run Wang, Alapati Tuerxun, Shuo Liu, Wei Xiao, Ján Drgoňa +2 more
code/data similarity 0.65
Abstract · 8 pages, 5 figures, submitted to RA-L

This paper presents dynamics-relaxed model predictive control (DR-MPC), a novel MPC formulation for legged locomotion, and a tailored interior-point method (IPM) solver. The formulation combines online optimization feasibility by construction with a contact-aware input parameterization. DR-MPC moves the dynamics equality and affine input constraints into quadratic penalties and retains only nonempty box constraints. The resulting box-constrained quadratic program (QP) has a block-arrow Hessian that enables the state and affine-output directions to be eliminated through a Schur complement. The solver factors only the reduced control system after swing-force elimination and contact-aligned move blocking. For the evaluated implementations using the same DR-MPC formulation, our method achieves median end-to-end MPC speedups of $16.0\times$ over HPIPM and $4.4\times$ over OSQP, with comparable locomotion performance in simulation. DR-MPC achieves a median onboard MPC end-to-end time of $4.4$ ms and is validated on a Unitree Go1 quadruped. Open-source code will be made available after publication.

0.27

Anti-Gravity Walking by a Flying Humanoid Robot via Thrust-Rate Input Whole-Body Model Predictive Control

cs.RO ·2026-09-07 ·Kazuki Sugihara, Kei Okada
top venue similarity 0.64
Abstract

Flying humanoids are expected to perform tasks in diverse environments, while their existing locomotion is mainly limited to aerial flight and ground walking. The capability to move in complex three-dimensional space can greatly expand their application range. For such walking motion on ceilings and similar anti-gravity environments, whole-body MPC is effective. However, the discontinuous changes in dynamic structure accompanying contact switching during walking can induce thrust spikes, resulting in control instability. Therefore, in this work, we propose and implement a real-time whole-body MPC framework for anti-gravity bipedal walking. First, we formulate whole-body MPC using the time derivative of thrust, namely thrust-rate, as the control input. This formulation guarantees continuity of the thrust trajectory during contact switching while preserving the sparse structure of the optimal control problem for fast computation. Second, we address the lack of natural support forces in anti-gravity environments. We introduce lower bounds on the foot-normal component of the contact force, and smoothly transfer them during the doublesupport phase. Finally, we implement the proposed framework and demonstrate anti-gravity walking by a flying humanoid through simulation and a hardware experiment. To the best of our knowledge, this is the first demonstration of multi-contact whole-body MPC for a transformable aerial robot and walking by a flying humanoid beyond the ground.

0.39

Learning Purposeful Co-designs of Bio-inspired Quadrupedal Robots

cs.RO ·2026-11-02 ·Fabio Boekel, Jiatao Ding, Cosimo Della Santina
similarity 0.61
Abstract · 10 pages, 7 figures, 6 tables

Treating morphology and control as separate design problems has constrained the efficiency and adaptability of quadrupedal robots, while current co-design approaches are often constrained by restricted design spaces. We overcome this limit by introducing Dogger, a bio-inspired quadruped with modular three-segment legs, four-bar linkages and adjustable passive knee compliance. A two-stage framework combining reinforcement learning and Bayesian optimization is developed: the morphology-conditioned control policy is trained across designs and then held fixed during task-specific design selection. The resulting designs and policies deployed zero-shot reduce the cost of transport by 18.6% and 35.7% for inspection and payload-carrying tasks. Comparisons demonstrate that full geometry-compliance co-design outperforms fixed and restricted design scopes. Cross-task tests further reveal distinct task-specific morphologies with shared mechanical trade-offs. These results provide hardware-level evidence that expanding the physical design space alongside learned control is essential to realize the full potential of task-driven morphology-control co-design in legged robotics.

0.12