CS Paper Radar

Energy Efficient Near-Threshold Voltage Massive MIMO Computing

MD Salman Sakib, Mehdi Safarpour, Pejman Ghasemzadeh, Shahriar Shahabuddin

cs.AR ·submitted 2026-11-04 16:50 UTC · v1

Abstract

Near-Threshold Computing (NTC) offers a substan- tial energy savings, i.e., up to 10x, for digital circuits. However, due to Process, Voltage, and Temperature (PVT) variations, low voltage operating digital processors face increased susceptibility to timing errors. This work equips conventional massive MIMO algorithms with computational error detection mechanisms, en- abling reliable operation down to near-threshold voltages. While conventional hardware based Timing Error Detection (TED) systems introduce substantial overhead, this work modifies MIMO algorithms to seamlessly integrate low overhead Algorithm Based Fault Tolerance (ABFT). A co-simulation framework combining transistor level SPICE simulations and workload aware fault injection is developed to investigate reliability, Bit Error Rate (BER), energy savings, and overheads of modified algorithms operating at low voltages. The transistor-level characterization was performed in PSpice using generic Level-1 Shichman-Hodges CMOS transistor models with Monte Carlo parameter variations. No specific CMOS fabrication process node was assumed. Conse- quently, the reported energy savings are analytical estimates and are not specific to a particular CMOS fabrication technology. We evaluate Gauss Seidel (GS), ADMM based infinity norm detection (ADMIN), and Conjugate Gradient (CG) detectors using circuit derived fault models. Results demonstrate remarkable algorith- mic resilience. Although undetected computational errors in some trials near the Point of First Failure (PoFF) were observed, BER increases by only 0.7% to 1.4%, while beyond PoFF, ABFT reported nearly all erroneous cases. The proposed checksum based ABFT detects most arithmetic and memory errors, with an estimated overhead below 2% for a 64 x 16 MIMO system, decreasing further for larger configurations.

Closest papers

Nearest neighbours by meaning across the whole index.

Dynamic Slack-Aware Clocking for Near-Threshold Tensor Processing Units (TPUs)

cs.AR ·2026-09-22 ·Muhammad Usman Nadeem, Sanghamitra Roy, Koushik Chakraborty
top venue similarity 0.59
Abstract · 31 pages, 13 figures. Accepted manuscript of ACM Transactions on Design Automation of Electronic Systems (TODAES); DOI: 10.1145/3837085

Operating Tensor Processing Units (TPUs) in the near-threshold computing (NTC) region significantly reduces energy consumption but introduces high delay sensitivity to process variation and data activity. Conventional designs typically rely on a conservative, fixed global clock to ensure safety, which leaves large portions of timing margin unexploited as most operations finish well before the clock edge. We propose Dynamic Slack-Aware Clocking (DSAC), a proactive framework that replaces worst-case timing with operation-specific adjustments. DSAC employs lightweight Hamming-Distance, Most-Significant-Bit, and Hybrid predictors to estimate the delay sensitivity of individual multiply-accumulate (MAC) operations and classify them into three timing tiers. These tiers are enforced locally via dummy-hold cycles under a fixed global reference clock, enabling fine-grained timing adaptation without global clock retuning or frequency scaling. A closed-loop feedback controller monitors timing violations and updates tier thresholds at runtime to maintain resilience. Experiments on quantized DNN benchmarks demonstrate that the MSB predictor maintains high inference accuracy, with an average loss of only 1% even at aggressive performance points. Furthermore, DSAC achieves up to 1.55X better energy efficiency at 2.15X frequency scaling compared to a baseline TPU, while incurring an area overhead as low as 13%.

0.40

Revisiting Cauchy-Schwarz Norm Bounds for SDC Detection in LLM Inference

cs.DC ·2026-10-13 ·Anton Altenbernd, Dylan Everingham, Philipp Wiesner, Odej Kao
similarity 0.55
Abstract

Large Language Models (LLMs) execute billions of floating-point operations per output token across many hardware accelerators. At this scale, hardware-induced faults can bypass system-level detection mechanisms and cause Silent Data Corruption (SDC). Algorithm-Based Fault Tolerance (ABFT) is the state-of-the-art technique for protecting matrix multiplication from such faults, but it incurs non-negligible computational overhead and requires thresholds to distinguish hardware-induced errors from floating-point roundoff. In this paper, we revisit Cauchy--Schwarz Norm Bounds (CSNB) as a low-overhead alternative for detecting SDC during LLM inference. We compare CSNB against ABFT through controlled fault injection and evaluate the runtime overhead of both verification and threshold determination across multiple model sizes, batch sizes, and generation lengths. Our results show that, on average, CSNB retains 99% of the fault detection capability of ABFT for the evaluated linear layers in dense LLMs, while reducing verification overhead by 87% and threshold determination overhead by 67%. For Mixture-of-Experts (MoE) router gate computations, however, CSNB retains only 55% of the fault detection capability of ABFT. These findings suggest that CSNB is a promising low-overhead alternative for protecting linear layers in dense LLMs, while checksum-based verification remains preferable for the evaluated MoE router gate.

0.13

ReBoT-MiCS: Reliability-Aware Bounding Time for Enhancing Timing Behavior of Embedded Mixed-Criticality Systems

cs.CE cs.SE ·2026-11-17 ·Mohammad Abbasinia, Behnaz Ranjbar, Akash Kumar
similarity 0.54
Abstract

In Mixed-Criticality (MC) systems, considering multiple Worst-Case Execution Times (WCETs) for the same task, corresponding to different system operation modes, presents a fundamental challenge in MC system design. Identifying suitable WCETs for lower (LO) criticality system operational modes is inherently difficult. Tight low WCET values may trigger frequent mode switches that degrade Quality-of-Service (QoS) by dropping/degrading the lower-criticality tasks and reducing their functionality. However, more conservative values reduce resource efficiency. Moreover, low WCET selection affects exposure assumptions under the adopted transient-fault model, which is used in reliability-aware scheduling analysis. Although some studies have considered low WCET determination to make a reasonable trade-off between processor utilization, mode switching probability and QoS, reliability constraints are typically addressed separately through fault-tolerance mechanisms. This separation overlooks the opportunity to use execution-time bounds as part of design-time reasoning about exposure-related reliability constraints. In this regard, we propose a reliability-aware analytical scheme, named ReBoT-MiCS, to determine low WCETs at design time, jointly balancing utilization, QoS, mode switches, and probabilistic reliability constraints of each task criticality level under a transient-fault exposure model. Experiments conducted with various synthetic and embedded benchmarks demonstrate the efficacy of the proposed scheme, in which utilization can be improved by up to 27.6% and 11.67% on average, while bounding the mode switching probability by up to 5.48%, and satisfying the specified reliability constraints

0.25

X-OPM: Explainable Automatic Digital On-Chip Power Modeling for Enhanced Robustness

cs.AR cs.AIcs.LG ·2026-10-06 ·Jingbo Jiang, Xizi Chen, Jian Peng, Wei Zhang
similarity 0.53
Abstract

Proactive power management systems reduce processor dynamic power through runtime power prediction and power-aware scheduling. Accurate, stable and low-overhead digital on-chip power meters (OPMs) are crucial for improving the prediction quality. Recent studies have explored various modeling methods, including using linear models, decision trees, and multi-layer perceptrons (MLPs) to construct OPMs. However, most current approaches train models end-to-end without analyzing the physical interpretability of features, affecting their ability to generalize to unseen workloads. Grounded in the design principles of synchronous digital VLSI circuits, X-OPM introduces a robust feature engineering framework that uses tree-based models to capture feature interactions and linear models for prediction. It also incorporates a human-in-the-loop workflow to balance model accuracy against modeling effort. Evaluated on a commercial C906 vector processor, X-OPM consistently achieves $R^2 > 0.93$ across all workloads with sampling window size set below $8$ cycles. In contrast, state-of-the-art methods including APOLLO, COBIT, and standard MLPs fail to generalize across all test cases. Layout with commercial EDA tools shows that X-OPM incurs an area overhead below $0.1\%$, which is on par with lightweight tree-based and linear models, and significantly smaller than MLP-based models.

0.20

Enabling Ultra-Low-Power Always-On Feedforward Leakage Suppression Logic Circuits with FDSOI

cs.ET ·2026-08-13 ·Clément Choné, Leslie Xu, Filippo Quadri, Pasquale Davide Schiavone, Alexandre Levisse +3 more
similarity 0.53
Abstract

The growing deployment of real-time applications on wearable and Internet of Things (IoT) edge devices has intensified the need for energy-efficient, high-performance systems that meet stringent timing and energy constraints. Events-driven architectures leverage the sparsity of real-time to further improve system energy efficiency by employing an always-on (AO) domain to monitor inputs and activate a high-performance (HP) domain only when relevant events occur. However, for low-duty-cycle applications, the energy bottleneck shifts toward the AO domain, where leakage power dominates overall consumption. To mitigate this issue, AO circuits are typically implemented using high voltage threshold (HVT) or ultra-high voltage threshold (UHVT) transistors, thereby avoiding sub- and near-threshold operation, which is highly sensitive to process, voltage, and temperature (PVT) variations. In this context, feedforward leakage suppression logic (FLSL) has recently emerged as a promising candidate, offering reduced leakage compared to conventional. However, previous studies report a significant degradation in FLSL leakage performance in technology nodes below 90 nm, primarily due to increased gate and junction leakage currents. FDSOI technology, with its ability to effectively suppress junction leakage, provides an opportunity to overcome this limitation and restore FLSL efficiency in advanced nodes. Therefore, we demonstrate in this work that FLSL implemented in a 22 nm FDSOI technology can significantly reduce the energy consumption of small AO circuits with low-frequency inputs compared to state-of-the-art ultra-low-power CMOS designs. Silicon measurements on an FIR filter and an AES cryptographic core show reduced operating voltage and up to 9.8 x and 1.83 x reductions in leakage power compared to equivalent HVT and UHVT CMOS implementations, respectively.

0.04

Reliable arithmetic circuits using less reliable (sub-digital) logic

cs.AR cond-mat.stat-mechphysics.app-ph ·2026-11-18 ·Trevor McCourt, Ila R. Fiete, Neil Gershenfeld, Isaac L. Chuang
unusual similarity 0.52
Abstract

The frequent static failure of CMOS logic gates at ultra-low voltages has historically been perceived as a strict barrier to extreme voltage scaling: this paper introduces a statistical circuit law proving this intuition wrong. We discovered a universal power law connecting gate and circuit static failure probabilities, revealing that circuit failure requires the simultaneous breakdown of an entire gate cluster rather than a single component. Because the required cluster size increases rapidly as voltage drops, low-voltage \textit{sub-digital} logic exhibits surprising inherent resilience to static failure. This insight stems from new theoretical tools we developed to quantify static failure, extending well beyond conventional voltage-margin analysis. Consequently, sub-digital processors could potentially offer a viable, near-term solution to drastically reduce the energy demands of AI.

0.45

A Probabilistic Behavioral RTL Simulation Framework for Probabilistic Compute Fabrics

cs.ET ·2026-11-18 ·Zehuan Wang, Chaohui Li, Ruihong Yin, Xunqi Li, Chris H. Kim
similarity 0.52
Abstract · 5 pages, 5 figures

Coupled oscillator Ising hardware can produce different solution qualities across repeated runs of the same problem, while a deterministic behavioral model used for the design yields a single outcome under fixed conditions. Capturing this stochastic variability during design time is essential for evaluating how closely simulation reflects silicon behavior. This work presents a probabilistic behavioral RTL simulation framework that introduces Gaussian timing variation into coupling delays. This variation changes oscillator timing during evolution, producing different outcomes across runs while retaining the existing chip control and readout blocks. The framework is evaluated against measurements from two chips: a 28-nm CMOS chip with 66 spins and a 16-nm FinFET chip with 49 spins, using 250 problems run 100 times repetitively. Compared with deterministic simulation, the model reduces the average absolute gap between sorted simulation and silicon outcomes by 14.0% and 28.4% on the two chips, respectively. These results demonstrate that a simple behavioral timing variation model can be a useful tool for designing and verifying probabilistic computing chips.

0.22

VARA: A Voltage-Aware ReRAM-Based Accelerator for Energy-Efficient Computing

cs.AR ·2026-08-31 ·Peng Dang, Yintao He, Huawei Li
similarity 0.52
Abstract

ReRAM-based in-memory computing (IMC) architectures are widely regarded as a promising approach to alleviating the computational bottleneck of conventional architectures. Since ReRAM crossbars perform matrix-vector multiplication (MVM) in the analog domain, their computational energy consumption is highly dependent on weight and activation distributions. However, most existing ReRAM accelerators focus primarily on weight optimization while paying limited attention to the impact of activations on computational energy consumption, leaving the energy-saving potential of activation sparsity largely underexploited. In this paper, we propose a voltage-aware ReRAM-based accelerator (VARA), along with its accompanying design methodology. Specifically, we first introduce a voltage-aware training (VAT) algorithm that incorporates a preset threshold into the activation function to steer the activation distribution toward zero values, thereby enhancing activation sparsity. Building upon this, we further propose a co-zero activation reordering (CAR) scheme for crossbar-level computation skipping. CAR clusters activation dimensions based on their co-zero correlations and consistently reorders both the activation matrix and its corresponding weights. This process consolidates scattered zero activations into contiguous zero-valued regions to maximize the benefits of crossbar-level computation skipping. Extensive experimental results demonstrate that, with only marginal accuracy loss, VARA reduces the average total system energy consumption by 60.12\% and improves the average system energy efficiency by 2.68$\times$ compared to the baseline, outperforming existing state-of-the-art accelerators for sparse-activation optimization.

0.24