CS Paper Radar

Simulation Modeling and Control of an Elastic Shaping Antagonistic Variable Stiffness Actuator

Yuanlong Ji, Ruizhe Jiang, Dongrun Jin, Xiangyu Xie, Junheng Lin, Xingbang Yang

eess.SY ·submitted 2026-11-05 06:09 UTC · v1

Abstract

Position--stiffness regulation of antagonistic variable stiffness actuators (VSAs) involves coupled nonlinear dynamics, parameter uncertainty, and feedback states that are not directly measured. This paper addresses this challenge through a simulation-based workflow that integrates elastic shaping, model verification, and layered nonlinear control. This study builds on a previously developed actuator comprising two crossed four-bar compliant transmission elastic units. Its optimized elastic mapping provides the structural basis, with an ADAMS torque-curve root mean square error (RMSE) of $2.57\,\mathrm{N\!\cdot\!mm}$ against the target. A control-oriented analytical model is implemented in Simulink and compared with the independently executed ADAMS model under matched inputs. The maximum joint-angle RMSE across the tested cases is $4.66\times10^{-3}\,\mathrm{rad}$. A layered controller combines extended Kalman filtering for state reconstruction, feedback linearization for nominal decoupling, and adaptive sliding-mode control for residual compensation. At the end of the nominal simulation, the joint-angle error is approximately $3.14\times10^{-5}\,\mathrm{rad}$. The stiffness error is $3.07\,\mathrm{N\!\cdot\!mm/rad}$ relative to a target of $50\,\mathrm{N\!\cdot\!mm/rad}$. Parameter-variation and ablation tests assess tracking performance and the effects of the controller modules within the evaluated conditions. The resulting workflow links structural-response modeling, state estimation, and robust control assessment, supporting repeatable comparisons beyond nominal tracking alone.

Comment
29 pages, 11 figures. Extends the structural study in arXiv:2609.18456 (ACIRS 2026) with dynamic modeling and closed-loop control evaluation

Closest papers

Nearest neighbours by meaning across the whole index.

Optimization Design and Simulation Validation of a Variable Stiffness Actuator Based on a Crossed Four-Bar Mechanism

eess.SY ·2026-09-16 ·Yuanlong Ji, Ruizhe Jiang, Xiangyu Xie, Junheng Lin, Dongrun Jin +1 more
published similarity 0.67
Abstract · 7 pages, 5 figures

This paper presents a bio-inspired antagonistic variable stiffness actuator (VSA) based on two crossed four-bar compliant transmission elastic units (CFB-CTEs). The design addresses the difficulty of combining nonlinear elastic shaping with low structural inertia in antagonistic VSA mechanisms. Inspired by the crossed constraint behavior of the anterior and posterior cruciate ligaments during knee flexion, the proposed actuator uses geometric transmission, elastic energy storage, and bilateral antagonistic arrangement to shape the output torque and equivalent stiffness. A multi-objective optimization model is established to balance torque tracking accuracy, equivalent inertia, and mass. The selected compromise design achieved a torque root-mean-square error (RMSE) of $0.883~\mathrm{N\,mm}$ and a total mass of $50.2~\mathrm{g}$. Its average equivalent inertia was reduced by about 78% compared with an independent torque-only optimized design. An ADAMS multibody model was further built to verify the structural response under single-input, opposite-input, and same-input conditions. The results support the feasibility of the proposed crossed four-bar elastic unit as a lightweight nonlinear elastic branch for antagonistic VSAs.

0.68

Control-Oriented Learning for Dynamic Tracking and Stability Analysis of Soft Pneumatic Actuators

cs.RO ·2026-08-25 ·Nithin S. Kumar, Eric J. Barth
similarity 0.58
Abstract · 8 pages, 10 figures

Soft pneumatic actuators offer inherent compliance and safe interaction but remain difficult to model and control because of their highly nonlinear, distributed dynamics. We present a control-oriented data-driven modeling and control framework that decomposes actuator behavior into a nonlinear static equilibrium model and a linear residual dynamics model identified using Extended Dynamic Mode Decomposition with control (EDMDc). This representation enables feedforward compensation, task-space feedback control, and local closed-loop stability analysis through an augmented linear model. Experiments achieve approximately 1 mm root mean square error (RMSE) during low-speed (approximately 10 mm/s) trajectory tracking and below 10 mm RMSE at higher speeds (approximately 100 mm/s). The framework further achieves stable tracking of highly dynamic user-generated references with peak accelerations exceeding 25 m/s^2 while simultaneously performing real-time obstacle avoidance. Finally, the proposed stability analysis is experimentally validated by accurately predicting stable, marginal, and unstable operating regimes. These results demonstrate that structured, control-oriented learning provides an accurate and practical framework for soft actuator control.

0.37

Prescribed-Time Contracting-Boundary Control of a Tendon-Driven Flexible Arm

cs.RO ·2026-09-19 ·Yi Lu, Chao Tang, Zhiji Han, Hongdu Wang
similarity 0.57
Abstract

This study develops a prescribed-time performance-shaping control method for curvature tracking of a single-segment flexible arm actuated by three antagonistic tendon pairs. A Cartesian curvature representation is introduced to avoid the undefined bending direction at the straight configuration and to establish an explicit six-tendon kinematic mapping. A cubic performance boundary contracts smoothly from an initially admissible error bound to a nonzero terminal accuracy bound within a prescribed time. Based on this boundary, a dual transformation combining static symmetric error scaling and time-varying behavior shaping maps the tracking error into a fixed unit box. The resulting controller guarantees boundary invariance, prescribed-time entry into the terminal accuracy region, and subsequent asymptotic convergence. Numerical evaluations with Python and OpenCR--MuJoCo, together with a supervised reduced-order experiment on a two-section, four-channel platform, provide complementary validation. Across six experimental trials, no violation of the prescribed boundary is observed, and the proposed controller reduces the mean terminal curvature RMSE by 32.5% relative to a matched baseline, with comparable terminal-band entry times. These results support the feasibility of the proposed approach in the reduced-order experimental setting.

0.23

H-PAC Hand: Control-Oriented Modeling and Tendon-Elasticity Compensation for an Underactuated Robotic Hand

cs.RO ·2026-08-17 ·Teng Yan, Jiongxu Chen, Teng Wang, Yue Yu, Qixiang Hua +3 more
similarity 0.56
Abstract · 7 pages, 6 figures. Extended preprint

Underactuated tendon-driven hands offer compact actuation and passive compliance, but tendon elongation under restoring-spring loading introduces configuration-dependent joint deviations. This paper presents H-PAC, a modular 6-actuator, 15-DoF robotic hand with a control-oriented modeling and implementation framework. A sparse analytical actuator-joint model is derived from the tendon-routing geometry, and a mechanics-based compensation model is developed to account for tendon-elasticity-induced joint errors. The proposed method is implemented in a hierarchical architecture: a host computer performs workspace-constrained posture mapping and compensation, while an ESP32 generates synchronized commands for six position-controlled servos. The same control parameters and execution strategy are used across all tasks without task-specific retuning. Monotonic servo-sweep experiments show that the compensation substantially improves joint-angle prediction. The MAE of the index DIP joint decreases from 1.15 degrees to 0.18 degrees, and all nine evaluated joints achieve an MAE below 0.23 degrees. Representative postures and grasping configurations are further executed using the same control pipeline without external joint or force sensing in the control loop. The results demonstrate a practical approach to improving posture reproducibility in compact underactuated robotic end-effectors.

0.34

Task-space model-based control of pneumatic soft actuators

cs.RO ·2026-08-27 ·Nithin S. Kumar, Joshua Gaston, D. Caleb Rucker, Eric J. Barth
top venue similarity 0.56
Abstract · 11 pages, 14 figures

Soft actuators enable dexterous and compliant interaction, but closed-loop task-space control remains challenging due to strong nonlinearities, distributed deformation, and uncertainty in their dynamics. This paper presents a real-time dynamic-model-based task-space feedback and estimation framework based on a non-minimal coordinate discrete elastic rod model formulated in absolute coordinates with holonomic constraints. The resulting structure preserves distributed mechanics while maintaining computational efficiency through sparse system matrices, enabling real-time control with up to 10 discretized rods. A quasi-static feedforward inverse model is combined with a task-space PI controller and a dynamic observer that fuses measurement residuals as virtual forces, enabling full-state estimation from sparse sensing. The approach is experimentally validated on three planar pneumatic soft actuators with varying geometries. Across five tasks, including drawing the digits 0-9 across the workspace (3-18 mm/s tip speed), tracking periodic motion (up to 37 cm/s), cross-platform generalization, reduced sensing conditions, and real-time user-defined references, our method achieves 1.5-2.3 mm root mean square error (RMSE) for precision motions and 5.5-12.4 mm RMSE at 1-2 Hz. Results demonstrate that structured, non-minimal dynamic models can enable real-time, high-precision, moderate-bandwidth task-space control of planar soft pneumatic actuators in free space.

0.27

Flexibility-Aware Robotic Manipulation: Deformation Estimation, Kinematics, and Control via Distributed Inertial Measurement

cs.RO ·2026-10-30 ·Amir Hossein Barjini, Sadeq Yaqubi, Pauli Mustalahti, Jouni Mattila
similarity 0.56
Abstract

Flexible robot links challenge the rigid-body assumption, making joint measurements alone insufficient for accurate manipulation. This paper introduces a flexibility-aware manipulation framework that connects structural dynamics directly to sensing, kinematics, and control. Instead of prescribing a dense inertial measurement unit (IMU) network, the dominant vibration modes of each flexible link are first identified from response-convergence and excitation-bandwidth criteria. Under a full-rank modal observability condition, $m$ retained modes require only $m$ independent slope measurements and one reference IMU, defining the minimum observable IMU configuration. The resulting measurements are used to reconstruct the continuous link deformation, which is then incorporated into flexibility-aware forward kinematics and a deformation-informed partial differential equation-based controller. Experiments on hydraulic single- and double-link manipulators evaluate the framework. On the long-reach double-link platform, the proposed kinematics achieves end-effector root mean square errors of $0.0107$~m, $0.0194$~m, and $0.0102$~rad while using fewer sensors than the piecewise-rigid method. Closed-loop reaching experiments further demonstrate real-time integration of IMU-estimated joint states and reconstructed deformation into the proposed controller. The results show that dominant modal information can determine sensing requirements and enable real-time flexibility-aware robotic manipulation.

0.34

Manipulation with Stability Guarantees: Linear Deformable Objects with Non-negligible Physical Response Grasped at Multiple Location

cs.RO ·2026-09-22 ·Daniel Feliu-Talegon, Cosimo Della Santina
similarity 0.55
Abstract · 19 pages, 13 figures

Most research on the manipulation of deformable objects focuses on lightweight systems with negligible mechanical response, effectively restricting attention to quasi-static regimes. This assumption excludes a broad class of practically relevant objects, such as hoses, pipes, and wiring harnesses, whose dynamics cannot be ignored during manipulation. In this work, we address this limitation by introducing a closed-loop control architecture that explicitly accounts for object dynamics and recasts manipulation as a shape-regulation problem. Control is achieved by modulating forces and torques applied at multiple fixed points along the object. This approach builds on three methodological contributions: a fully dynamic model of linear deformable objects based on discrete strain parameterizations; an extension of the notion of actuation coordinates to SE(3), yielding a structured and inherently underactuated control architecture; and nonlinear feedback strategies providing explicit conditions for steady-state convergence to desired configurations. Extensive simulations on representative manipulation tasks demonstrate the performance gains enabled by the proposed modelbased formulation. We finally validate the approach experimentally through a real-time closed-loop implementation with online shape estimation, confirming its practical feasibility and effectiveness

0.33

Reduced Cartesian Kinetostatics for Tendon-Driven Continuum Robots: Residual-Stabilized Full-Shape Propagation

cs.RO ·2026-09-24 ·Ke Wu, Fangju Yang, Xiaohui Zhang, Zhengqiang Zhang, Jingang Yi +1 more
hot direction similarity 0.53
Abstract

Many planning and control tasks for tendon-driven continuum robots (TDCRs) require the complete Cartesian backbone geometry. We present a reduced Cartesian framework for planar, axially compressible TDCRs that propagates equilibrium configurations along prescribed tendon-force and tendon-displacement trajectories. The backbone is represented by two global position fields. Following exact variation, a Taylor-Galerkin reduction condenses prescribed spatial properties and distributed loads into offline moment vectors, yielding analytic reduced residuals and Jacobians without online spatial quadrature or numerical differentiation. Analytical differentiation and residual correction yield first-order rate systems requiring one fixed-dimensional linear solve per rate evaluation after initial equilibrium alignment on a regular branch. Across four simulated cases covering variable tendon routing, nonuniform geometry, axial compression, and their combined effects, the propagated Cartesian shapes and distributed strains closely match pointwise geometrically variable-strain (GVS) equilibrium solutions. Residual correction suppresses propagation drift across the tested step sizes while adding only about 0.98% to the mean update time of uncorrected Euler. The proposed method requires 0.508 ms per update on average, approximately 11 times faster than pointwise GVS solves. Displacement-driven experiments yield a maximum normalized mean backbone position error of 1.02% and a maximum end-effector position error of 0.28%. These results support efficient and accurate Cartesian full-shape prediction along prescribed actuation paths.

0.30