CS Paper Radar

Whole-Body Elasto-Geometrical Calibration of Wheeled Humanoid Robots Using a Shared-Waist Dual-Chain Model

Pengxin Zha, Yi Lu, Haojun Ma, Jun Zhu, Minghao Qiu, Xiaoyan Wang, Wei Shan, Maoqing Yao

cs.RO ·submitted 2026-11-05 07:07 UTC · v1

Abstract

Wheeled humanoid robots carry both arms on one actuated waist, usually without torque sensors, so the accuracy of both end-effectors depends on a single waist model. After a first stage that estimates the tracker and target extrinsics, we identify the waist and both arms in one problem from the target positions on both flanges, measured by an optical tracker. The kinematic model is complete, with waist-base, parallel-axis, and branch parameters; arm compliances are driven by measured torques and waist compliances by gravity torques of the robot's mass model; and Gaussian priors with evidence-maximizing scales stabilize the estimate. Independent and sequential single-chain calibration are restrictions of this problem, and its waist information is the sum of the single-chain Schur complements. On two robots with different waists, each without and with a payload, calibration reduces the mean errors on held-out poses from 11.3-31.1 mm to 0.50-1.11 mm. For every training-set size from 20 poses to all, the method has 17-63% lower mean errors than adaptations of two published whole-body calibration methods, mainly through the waist compliance. Independent calibration yields two waist models; using either for both arms raises the other arm's error to up to 3.21 mm.

Comment
10 pages, 6 figures, 5 tables

Closest papers

Nearest neighbours by meaning across the whole index.

OmniCalib: Target-Free, Task-Structured Self-Calibration for Humanoid Robots

cs.RO ·2026-09-17 ·Kaixiang Lu, Haiyu Lan, Chunxiao Qiao, You Li, Enyu Li +4 more
similarity 0.63
Abstract · 6 figures, 3 tables

Assembly, wear, and component replacement perturb the sensor extrinsics and joint zeros encoded by a humanoid CAD model. Existing procedures calibrate one sensor pair or require external fiducials. Using only robot-native motion and onboard sensing, we present OmniCalib, a target-free workflow that calibrates the full upper limbs---all 14 arm joint zeros and the extrinsics of both wrist and chest cameras---as well as lower limbs and the multi-camera head rig. Each module matches a robot-native task to a parameter block, checks observability, and writes only supported corrections to the CAD model. Our depth ICP method recovers all 14 arm joint zeros and calibrates all RGB-D camera extrinsics without any calibration target. Relative to CAD, the estimated extrinsic corrections are 10.56 mm and 1.74 degrees for the left wrist, 6.33 mm and 1.25 degrees for the right wrist, and 9.81 mm and 0.929 degrees for the chest RGB-D camera. ICP point-to-plane residual is 2.09 mm. On the same injected offsets, ICP and ArUco recover all 14 joint zeros below the 0.1-degree encoder-resolution reference. On an AGIBOT A3 Ultra humanoid, four static double-support stances recover all 12 lower-limb joint-zero offsets injected with an RMS error of 0.063 degrees. The head module combines multi-camera visual odometry with legged odometry and dynamic compensation through the live ROS transform tree. Using only planar walking, it attains a mean SO(3) error of 1.061 degrees across three sequences. The best sequence reaches 0.775 degrees, competitive with iKalibr at 0.902 degrees from rich 6-DOF excitation. Rig-relative angles repeat within 0.140 degrees. Injection recovery and held-out tests validate each observable block.

0.25

Beyond Kinematic Tracking: Preserving Expressive Characteristics in Humanoid Whole-Body Control

cs.RO ·2026-10-14 ·Lingfan Bao, Hanshang Zhu, Yan Pan, Jincheng Wang, Jingyang Yu +4 more
similarity 0.63
Abstract · Under Review

Whole-body control plays a crucial role in enabling humanoid robots to execute expressive motions. Faithful execution requires preserving both the intended action and its expressive characteristics. Existing whole-body trackers typically balance joint and keypoint tracking with physical stability across diverse motions, but these objectives do not necessarily prioritize the expressive characteristics of each action. Our analysis shows that lower average positional tracking error does not guarantee better preservation of dynamic and postural motion characteristics. To address this gap, we propose a residual learning framework with compensation objectives targeting amplitude, energy, body expansion, body lean, and pelvis height. To concentrate compensation while limiting interference with the underlying tracking behavior, motion-aware gating allocates correction capacity according to body-part activity, preserving larger correction ranges in more active parts and restricting them elsewhere. For each frozen tracker, we train motion-specific residual policies and distill them into a unified policy shared across motion categories. Simulation and physical experiments on the Unitree G1 across eight motion categories demonstrate superior preservation of dynamic and postural motion characteristics compared with the corresponding baselines.

0.12

Dataset-Free Compliant Humanoid Loco-Manipulation with Dynamic Online Posture

cs.RO ·2026-10-05 ·Seungho Yeom, Zhenyu Wu, Jaeyoung Huh, Diego Williams, Yuheng Zhi +2 more
similarity 0.63
Abstract

Most humanoid loco-manipulation controllers require human motion data to learn whole-body coordination and posture, leaving policies reliant on external sources to provide this data. We present OCLO (Online-posture Compliant LOco-manipulation), a humanoid loco-manipulation system trained without human motion data and commanded only through two end-effector targets. Because these targets do not uniquely determine whole-body posture, OCLO generates pelvis height and torso orientation online using an analytic reachability prior, further refined through policy-in-the-loop sampling with a task-agnostic cost. OCLO also learns whole-body compliance by displacing end-effector references according to measured forces through a spring-damper model, encouraging the legs, waist, and pelvis to yield to external loads. In simulation, using the reachability prior leads to a 77.8% success rate in acquiring the commanded reference, a vast improvement over the 37.8% success rate accomplished without the prior. Further, refinement reduces end-effector orientation error across all evaluated tasks. The same posture module improves a pretrained SONIC controller on four of five tasks. Without compliance training, policies tend to lose balance under disturbances rather than sacrifice tracking. On a Unitree G1, OCLO maintains balance under end-effector disturbances that cause its ablations to fail and performs seven loco-manipulation tasks, including crouched walking and picking up a box from a low surface. Project website: https://oclo-humanoid.github.io/

0.27

Learning Accurate End-Effector Trajectory Tracking with Inertial Feedback for a Quadruped Manipulator

cs.RO ·2026-11-17 ·Dohyeon Kim, Seungyong Han, Yeongtae Jung
similarity 0.61
Abstract

Accurate end-effector trajectory tracking on quadruped manipulators is challenging because uncertainties in actuators, foot-ground contact, and geometric errors are propagated through the leg-arm kinematic chain. Detecting such errors requires sensing beyond joint encoders that can capture the effects of these uncertainties on the robot's motion, since joint encoders only provide measurements at the actuated joints and cannot fully observe mechanical errors such as backlash, dimensional inaccuracies, or structural deformation. This work addresses these challenges using a reinforcement learning framework with end-effector (EE) inertial feedback, targeting local high-accuracy manipulation while maintaining a nominal body pose and support configuration without intentional body motion or foot repositioning. The learned policy uses EE inertial measurements to compensate for tracking errors induced by uncertainties throughout the leg-arm system that cannot be fully inferred from proprioception alone. Simulation and real-world experiments on continuous EE trajectory tracking show overall improvements relative to nominal and proprioception-only baselines. In real-world experiments, the proposed policy reduces the MoCap-based RMSE by 17.3% and 28.0% relative to the nominal baseline under the two in-distribution (ID) command conditions, respectively, and by an additional 12.6% and 15.9% relative to the proprioception-only baseline. Furthermore, the trajectory-wise RMSE between FK-reconstructed and motion-capture-measured end-effector positions averaged 12.61+-2.15mm (mean+-standard deviation) across 24 controller-trajectory combinations, revealing a substantial discrepancy between nominal kinematic reconstruction and measured end-effector motion.

0.18

General Performance Guarantee for Human Torque Estimation-Based Task-Agnostic Assistive Exoskeleton Control

cs.RO cs.LGeess.SY ·2026-09-30 ·Duy Hoang, Bastien Berret, Olivier Bruneau, Laurent Fribourg
theory similarity 0.60
Abstract · 10 pages, 8 figures

Accurate human torque estimation is crucial for enabling task-agnostic control in robotic exoskeleton systems. However, estimation errors may cause mismatches between the robot assistance and the human intention, degrading controllability and task performance. In this paper, we address this issue by formally defining matched assistance as scenarios in which the robot positively contributes to human movement. Based on this definition, we develop a theoretical framework to design the robot's desired interaction torque that guarantees a lower bound on the matched assistance probability. Importantly, the proposed guarantee holds over the entire torque distribution, including unseen data beyond the training tasks. This provides our method with strong reliability and generalization, both of which are critical for effective exoskeleton control. The proposed strategy is implemented on the ABLE upper-limb exoskeleton and evaluated in a multi-task setup. Experimental results validate the theoretical guarantees and demonstrate that the proposed strategy achieves effective general performance across several tasks, guaranteeing movement smoothness while reducing human physical effort.

0.19

Contact-Constrained Lower-Limb Joint-Offset Calibration for Humanoid Robots

cs.RO ·2026-09-02 ·Kaixiang Lu, Haiyu Lan, Chunxiao Qiao, You Li, Chengyuan Luo +3 more
top venue similarity 0.60
Abstract

Accurate joint encoder offsets are essential for kinematic consistency in humanoid lower limbs, yet existing calibration methods typically require external motion-capture systems or fiducial targets. We present a self-contained calibration framework exploiting only onboard joint encoders and a pelvis-mounted IMU during static double-support contact. The inter-foot transform from forward kinematics must stay constant when both feet are fixed; minimizing its posture-dependent dispersion yields a nonlinear least-squares problem over the 12-dimensional offset vector. A Hessian eigenstructure analysis shows that parallel pitch axes induce a rotational coupling. Orientation residuals then observe only the pitch-offset sum, while translation and posture diversity set the remaining numerical observability. For the A3 pitch-to-roll-to-yaw ordering, hip-roll and hip-yaw excitation reduce hip-pitch coupling. A standing-posture knee prior then anchors the remaining weak pitch-chain decomposition. Simulation and real-machine injection tests show consistent recovery, and on held-out recordings calibration reduces foot-height RMS residuals from 4.26 to 2.20 mm on A3 and from 8.03 to 1.43 mm on A2. An independent LiDAR-inertial reference checks the pitch-coupled channel. Removing an injected pitch offset moves the leg-odometry vertical drift back toward the LiDAR trajectory. A few static double-support stances thus provide contact-consistent corrections for well-excited directions. Individual offsets in the weak pitch chain remain prior-dependent.

0.44

Workhorse: Learning Robust Whole-Body Humanoid Loco-Manipulation from Human Data

cs.RO cs.LG ·2026-10-06 ·Songbo Hu, Qiayuan Liao, Yufeng Chi, Kevin Zakka, Yakun Sophia Shao +2 more
code/data similarity 0.60
Abstract · 9 pages, 8 figures, 2 tables. Project page: https://hybridrobotics.github.io/workhorse/

Humanoid robots still struggle to plan contact-rich whole-body manipulation from egocentric RGB and proprioception. Workhorse learns such manipulation from robot-free human demonstrations. A visual planner predicts five-link targets: the poses of the torso, both wrists, and both feet. A reinforcement-learning whole-body tracker follows them on the robot. Both policies train separately on the same recorded human poses, without retargeting. We augment the training data of each policy to imitate the errors that the other makes at deployment. On a real Unitree G1, Workhorse transport boxes with its hands and a kick, catches a thrown box, and topples and climbs a suitcase. During box transport, we show recoveries after a person pushes the robot or takes the box away. In a simulated copy of the demonstration room, the system completes box transport in 77% of episodes, and in 64% under 40 N.s pushes. With both policies retrained from the same demonstrations, a simulated second humanoid completes box transport in 83% of episodes without pushes.

0.64

MotionSkill: From Bipedal Motion Video to Control across Embodiments

cs.RO ·2026-11-12 ·Philip Niu, Xiaofeng Han, Sylvie Pan, Yang Wang
similarity 0.59
Abstract · 8 pages, 7 figures, 5 tables. Fortune AI technical report

Reusing a demonstrated gait can reduce the work of specifying the same motion for each biped. A video captures the timing of a step, but each robot must execute it with its own limbs and actuators. MotionSkill recovers a timed reference once from monocular video and adapts it to each target in simulation. It aligns root motion and body landmarks in a common frame and records which landmarks are available at each instant. At each source timestamp, the mapper preserves limb directions, uses the target segment lengths, and solves inverse kinematics under joint limits and closure constraints. In MuJoCo, we train a separate residual policy for each of ten bipeds on its mapped reference from one four-second walking clip. Each policy uses the measured robot state to correct joint commands during contact. From initial states held out during training, MotionSkill completed 98% of trials on the original video and 26% with the upper body occluded for one second.

0.15