CS Paper Radar

Laser-Diode LiFi With Diffused-Beam Optics: System-Level Modeling and a Cross-Validated ns-3 Simulation Framework

Hussain Ahmad, Syed Muhammad Talha Gillani, Toheed Omer, Saleem Aslam

eess.SP cs.NI ·submitted 2026-08-11 14:19 UTC · v1
publishedcode/data

Abstract

Laser diodes (LDs) promise an order-of-magnitude bandwidth advantage over light-emitting diodes for indoor optical wireless access, but reported prototype studies frequently leave the gap between hardware demonstrations and system-level performance unquantified. This paper develops a complete, reproducible system model of a diffused-beam LD LiFi transceiver - a 500-mW laser source beam-shaped by a holographic diffuser, an intensity-modulation/ direct-detection (IM/DD) receiver, and adaptive M-QAM signaling - and embeds it in two cross validated simulators: an open ns-3 module providing full-stack network simulation (channel, PHY, ARQ MAC, Net Device, IP/UDP/TCP) and a Python link-level engine used for Monte Carlo validation of all analytical error models. Starting from a hardware prototype that transferred data, real-time voice, and images over a 14-m line-of-sight link, we identify and close the technical gaps typical of prototype-class reports: serial-interface throughput ceilings misread as optical-link capacity, absent noise modeling, unmeasurable error floors, and unexamined beamwidth/coverage trade-offs. The framework shows that the same optical front end, freed of its 2-Mbaud UART bottleneck and driven at its 250-MHz electrical bandwidth, supports 930 Mb/s net at 14 m under a $3.8 \times 10^{-3}$ HD-FEC threshold with 16-QAM, scales to 1.86 Gb/s at 5 m with 256-QAM, and sustains on-off keying to 23.3 m; a $20^\circ$ diffuser covers a 4.2-m-radius cell of a standard room at desk height. Network simulations over the ns-3 stack yield saturation goodput within 7% of the PHY line rate and sub-0.11-ms 99th-percentile latency at 70% load. All models, code, and figures are released for reproduction.

Comment
8 pages, 15 figures, Journal
Journal ref
IEEE Journal of Indoor and Seamless Positioning and Navigation 2026

Closest papers

Nearest neighbours by meaning across the whole index.

Diffused-Beam Laser-Diode LiFi Under Realizable Receiver, Noise, and Safety Constraints: Design-Space Analysis and an Open Cross-Verified Simulation Framework

eess.SP cs.NIcs.PF ·2026-08-15 ·Hussain Ahmad, Saleem Aslam, Ammara Nasim, Syed Muhammad Talha Gillani, Toheed Omer
code/data similarity 0.75
Abstract · 15 pages, 16 figures, Journal

Link-budget studies of indoor optical wireless systems frequently assume receiver parameter sets--large photodetector area, large transimpedance, and wide bandwidth simultaneously--that violate basic circuit constraints, and noise budgets that omit dominant amplifier and laser noise. This paper develops a realizability-constrained design-space analysis of a diffused-beam laser-diode (LD) LiFi link anchored to a hardware prototype. The analysis couples the generalized Lambertian channel of a holographic-diffuser source to a receiver model that enforces the transimpedance-amplifier gain-bandwidth/capacitance constraint and carries a complete noise budget: shot, feedback-resistor thermal, input current noise, capacitance-driven voltage-noise gain, and laser relative intensity noise (RIN). Against this budget we evaluate unipolar M-PAM under two FEC tiers (7%-overhead hard-decision at $3.8 \times 10^{-3}$, 20%-overhead soft-decision at $2 \times 10^{-2}$), first-bounce diffuse multipath, and a quantitative extended-source eye-safety assessment. The full model predicts 140 Mb/s net at the prototype's demonstrated 14-m range with 6.7 dB margin (OOK, HD tier), 240 Mb/s at the zero-margin 4-PAM/SD reach boundary of 14.0 m, and 480-558 Mb/s at 5 m--a factor 3.9-6.6 below what the same link yields under a naive textbook budget, quantifying how strongly idealized assumptions inflate LiFi projections. First-bounce analysis shows the downfacing-source/up-facing-receiver geometry confines multipath to a worst-case LOS-to-diffuse ratio of 4.2 dB and delay spreads below 0.13 ns, and the 500-mW source remains a factor $\ge 7.8$ under the Class-1 eye-safety limit. All models are released as an ns-3 module and Python engine backed by automated testing.

0.26

Statistical Inference-Based Channel Estimation for LD-Driven Visible Light O-OFDM Systems in the Presence of Relative Intensity and Input-Signal-Dependent Shot Noise

eess.SP ·2026-09-14 ·Shubham Saxena, Karra Sreeman Reddy, Suraj Srivastava, Subrahmanya Swamy Peruru, Aditya K. Jagannatham +1 more
benchmarktheory similarity 0.52
Abstract

Laser diode (LD)-based luminaires are gaining increasing attention in automotive applications and are expected to extend to residential and commercial environments, creating opportunities for high-bandwidth visible light communication (VLC) systems. However, practical LD-based VLC links are impaired by input-signal-dependent shot noise (ISDSN), relative intensity noise (RIN), and thermal noise, which affect reliable channel estimation (CE). This work investigates their joint impact on receiver-side CE in a single-input single-output (SISO) optical orthogonal frequency division multiplexing (OOFDM) VLC system under a statistically random channel model. A statistical inference framework is developed in which the receiver exploits observed signal variations to estimate the channel under optical impairments. Closed-form expressions are derived for least squares (LS), maximum likelihood (ML), maximum a posteriori probability (MAP), minimum mean square error (MMSE), and linear MMSE (LMMSE) estimators. In addition, the Bayesian Cramer-Rao lower bound (BCRLB) is derived to benchmark mean square error (MSE) performance. Monte Carlo simulations for direct current-biased O-OFDM (DCO-OFDM) and asymmetrically clipped O-OFDM (ACO-OFDM) validate the analysis. Results show substantial CE degradation under the joint presence of ISDSN and RIN, while the MMSE estimator consistently achieves the lowest MSE, demonstrating strong potential for robust and adaptive receiver operation in practical VLC systems.

0.37

Low-complexity Soft-decision LLR Calculations for Next-generation IM-DD Systems with RIN

eess.SP ·2026-08-20 ·Felipe Villenas, Yunus Can Gültekin, Alex Alvarado
published similarity 0.51
Abstract

The demand for higher speeds in intra-data center interconnects will eventually require high-order pulse amplitude modulation (PAM) combined with soft-decision (SD) forward error correction (FEC). The laser relative intensity noise (RIN) is an important noise impairment that limits the performance of high-speed intensity-modulation (IM) and direct-detection (DD) systems, as it induces a channel with signal-dependent noise. In this paper, we show that an accurate calculation of the log-likelihood ratios (LLRs) is critical for the performance of the SD-FEC decoder in RIN-dominated IM-DD systems. First, we show that assuming signal-independent additive white Gaussian noise (AWGN) statistics to compute LLRs results in a significant penalty in performance. As an alternative, we propose a low-complexity piecewise linear approximation of the exact LLRs of Gray-coded PAM-4 and PAM-8 for the RIN-dominated IM-DD channel. We show using the generalized mutual information that our approximation results in no performance loss versus using exact LLRs, unlike the AWGN-like assumption. Furthermore, we validate the analysis with bit error rate (BER) performance of SD decoding. We show that our approximation matches the BERs achieved using exact LLRs. Therefore, our approximation avoids a BER error floor penalty of up to 7.2 times using an extended Hamming code with PAM-4, and up to 2.41 dB of optical modulation amplitude penalty using high-code-rate low-density parity-check codes with PAM-8 for the same target BER.

0.33

Scattering-Mediated NLOS Ultraviolet Communication: Channel Characterization, Modeling, and Data Transmission

eess.SP ·2026-10-12 ·Jian Shao, Tilahun ZerihunGutema, Wasiu O. Popoola
similarity 0.51
Abstract

Solar-blind ultraviolet (UV) optical wireless communication (OWC) enables non-line-of-sight (NLOS) transmission through atmospheric scattering. This work presents a comprehensive experimental and simulation study of a 100 m outdoor UVC link with comparative measurements under LOS-blocked and open-field conditions. The results show that LOS-blocked scattering-mediated links exhibit substantially higher path loss and narrower bandwidth than corresponding open-field measurements, highlighting the impact of residual LOS components in practical diffused beam UVC experiments. A photon-tracing Monte Carlo (MC) framework incorporating realistic transmitter/receiver characteristics and obstacle geometry is further developed to reproduce the measured channel characteristics with high accuracy. Despite the severe path loss and pulse broadening effects, reliable 20-200 kbps transmission is experimentally demonstrated over the 100 m LOS-blocked link using on-off keying (OOK) and pulse-position modulation (PPM), representing the longest-distance and highest-data-rate experimental demonstration of an explicitly LOS-blocked scattering-mediated UVC link reported to date.

0.31

Impact of Optical Reconfigurable Intelligent Surfaces on Channel Estimation for VLC Systems

eess.SP ·2026-08-25 ·Borja Genoves Guzman, M. Julia Fernández-Getino García
published similarity 0.50
Abstract · Accepted for publication in IEEE Globecom 2026

Visible light communication (VLC) offers wireless data connectivity indoors, yet its performance is severely limited by link blockages. While optical reconfigurable intelligent surfaces (ORISs) have been proposed to overcome these blockages, existing literature predominantly relies on the unrealistic assumption of ideal channel state information. In this paper we investigate the contribution of ORIS elements in VLC systems under practical, non-ideal channel estimation scenarios. We analyze the communication performance using two pilot-based estimation techniques: pilot symbol assisted modulation (PSAM) and superimposed training (ST), evaluating the impact of data power allocation factors and averaged orthogonal frequency division multiplexing (OFDM) symbols. Our results show that PSAM with an ORIS deployment enables optimal large data power allocation factors, resulting in spectral efficiency improvements that surpass scenarios with ideal channel estimates but without ORIS deployment. While ST performs well with a large number of averaged OFDM symbols, it is unable to overcome the performance of PSAM when ORIS elements are deployed. We also find the system robust to imperfect ORIS orientation; even with only half of the elements accurately aligned, performance remains acceptable. Ultimately, we show that spectral efficiency values of approximately 5 bits/s/Hz are achievable using ORIS with PSAM, a performance comparable to, or even exceeding, that of unobstructed line-of-sight links.

0.31

An FPGA-in-the-Loop Testbed for MU-MIMO OFDM Beamforming over Ray-Traced Wireless Channels

cs.NI ·2026-09-06 ·Drew Schlesener, Tolunay Seyfi, Fatemeh Afghah
similarity 0.50
Abstract

Wireless networks face ever expanding throughput demands from heterogeneous, high-density user populations, requiring beamforming algorithms that adapt to channel conditions with low latency. Validating such algorithms requires either costly over-the-air testbeds or simulation environments that lack the timing and resource constraints of real hardware, leaving a gap between algorithm design and hardware-realizable deployment. This work presents a frame-based hardware-in-the-loop (HIL) testbed that closes that gap by coupling an FPGA-based implementation of OFDM Waveforms with MU-MIMO beamforming to NVIDIA Sionna's ray-tracing channel simulator, enabling a physical base-station architecture to transmit and receive against a Sionna-rendered digital-twin propagation environment. Unlike prior work that validates beamforming algorithms either purely in simulation or on full RF testbeds, this architecture allows beamforming logic running on actual FPGA fabric to be evaluated under realistic, controllable, and repeatable channel conditions, including UE mobility and site-specific multi-path, without requiring an anechoic chamber or live RF front end. We detail the FPGA OFDM transmit/receive pipeline, the synchronization and data interface between the FPGA and the Sionna environment, and validation of signal quality under AWGN and ray-traced channel conditions, establishing this testbed as a platform for hardware-validated beamforming research.

0.26

LiDAR-Derived Surface Priors for Multimodal Sensing-Assisted NLoS Beam Search in Indoor 60-GHz Networks

eess.SY ·2026-08-18 ·Amod Ashtekar, Dalton Davis, Rafaela Lomboy, Omar Ibrahim, Raj Sai Sohel Bandari +1 more
similarity 0.49
Abstract

Highly directional 60-GHz Internet-of-Things (IoT) links can exploit naturally occurring indoor surfaces to sustain connectivity under blockage. Identifying viable non-line-of-sight (NLoS) paths, however, can require extensive RF beam training. This paper investigates whether LiDAR can reduce this search overhead by providing a surface-aware prior without assuming a direct mapping between optical return and mmWave reflection. The proposed framework uses LiDAR-derived geometry and return statistics to rank candidate propagation directions, while RF measurements remain responsible for final beam selection. The experimental validation is organized in three stages to separate descriptor robustness, cross-modal association, and beam-search performance. Controlled LiDAR measurements first quantify how geometric and radiometric surface descriptors vary with acquisition geometry. Matched LiDAR and 60-GHz measurements in an L-shaped corridor then determine whether these descriptors are associated with the measured surface-mediated RF response under a prescribed NLoS interaction. Finally, a separate room-scale campaign evaluates the resulting prior using exhaustive TX-RX beam maps without prescribing the underlying propagation mechanism. The measurements show that descriptor reliability depends on acquisition geometry and point-cloud representation, and that LiDAR and RF surface responses exhibit cross-modal association without supporting deterministic RF-power prediction. In the room experiment, local three-ring 3-D planarity retains a beam within 3 dB of exhaustive search at 74.5% of the measured locations while reducing RF beam-pair probing by 72% relative to exhaustive probing over the candidate search region. These results establish LiDAR-derived local surface structure as a communication-oriented prior for concentrating RF probing and reducing mmWave beam-search uncertainty.

0.20

Progressively Attenuated Multi-Branch Reception for Inter-HAPS Optical Links

eess.SP ·2026-09-11 ·Meysam Ghanbari, Betul Beidas, Wasiu O. Popoola, Mazen O. Hasna, Khalid A. Qaraqe +1 more
similarity 0.48
Abstract

Inter HAPS optical links can experience receiver saturation at short separations and become signal to noise ratio (SNR) limited at longer distances. This work proposes a saturation aware spatial multi branch intensity modulation direct detection receiver using nonoverlapping apertures with progressive attenuation and selection of the nonsaturated branch with the highest instantaneous SNR. A Gaussian beam model with finite aperture pointing loss and common two dimensional pointing jitter yields closed form branch level expressions for saturation, insufficient SNR, usability, and outage probabilities. Results show that additional branches suppress short range saturation outage, shift the minimum outage point toward shorter separations, and enable progressive attenuation to control the saturation SNR tradeoff. Monte Carlo simulations closely match the analytical results. Overall, the proposed architecture provides a low complexity approach to extending the usable dynamic range of inter HAPS optical receivers.

0.24