CS Paper Radar

Modeling and Control of an Eel-Inspired Soft Robot for Design Optimization

Zhangjingyi Jiang, Mark Campbell

cs.RO ·submitted 2026-08-14 19:54 UTC · v1
published

Abstract

Anguilliform locomotion is a highly efficient swimming mode; the advent of new materials for soft robots enables the development of an eel-inspired soft robot. This paper presents a simulation model of an eel-inspired soft robot designed for anguilliform swimming. This model can aid in design optimization and the development of model-based estimation, reasoning, and control systems. A Finite Element Method (FEM) model of an elastic rod is used to capture the soft materials of the robotic fish, which makes it particularly amenable to variation over time as the material properties change. The material model is coupled with a hydrodynamic force model to simulate the behavior of a soft, elongated robot in water. The model is used to demonstrate the effectiveness of the proposed control approaches in achieving desired swimming behaviors. It also provides insights into design decisions, including the robustness of different system configurations and the impact of material degradation and failure. The results show that slightly asymmetric designs are advantageous, offering comparable swimming velocities but greater maneuverability. This model can be used to guide future robotic design decisions aimed at optimizing performance for specific tasks.

DOI
10.1109/CASE59546.2024.10711519

Closest papers

Nearest neighbours by meaning across the whole index.

Real-time Estimator of Actuator Control and Health (REACH) on an Eel-Inspired Soft Robot

cs.RO ·2026-08-14 ·Zhangjingyi Jiang, Myungsun Park, Michael T. Tolley, Mark Campbell
published similarity 0.72
Abstract · Corrected some minor typos

An actuator health estimation algorithm for a soft swimming robot that can perform anguilliform swimming is developed. Due to harsh operational environments of underwater robots, and the common degradation of soft robot materials and actuators, accurate estimation of actuator functionality is necessary for robots to perform their missions as well as return to base in the event of actuator degradation and failure. Termed REACH (Real-time Estimator of Actuator Control and Health), the architecture employs a soft robot model, sigma point filter, and a formal statistical hypothesis test to adequately capture the nonlinearities and changes over time. The performance of REACH using three sensor types (GPS, IMU, and Bend Sensor) with one sensor on each actuator is compared, demonstrating that both bend sensor and IMU are adequate choices. Sensor quantity and placement are evaluated for IMU and bend sensor, showing two sensors are sufficient for IMU, whereas three sensors are needed for bend sensor. Three swimming gaits (linear swimming, wide turning, tight turning) are compared, demonstrating that REACH can successfully predict actuator health for all three gaits, with minimal differences in performance. A filter validation method shows the fault estimation algorithm is statistically consistent in finding the correct degradation. The approach is experimentally evaluated using bend sensor data collected from a fish robot, demonstrating that REACH can successfully estimate actuator health with noisy data and variations in manufacturing.

0.28

OmniFish: A Bioinspired, Modular, Reconfigurable Soft Robotic Fish Enabling Multi-Modal Swimming

cs.RO physics.flu-dyn ·2026-11-18 ·Mathias Jensen, Saravana Prashanth Murali Babu
similarity 0.68
Abstract · Under review at Bioinspiration & Biomimetics. 10 figures, 7 tables

In this work, we introduce OmniFish, a bioinspired modular soft robotic fish designed to emulate the full spectrum of body and/or caudal fin (BCF) locomotion modes within a single robotic platform. The design combines morphology averaging across representative fish species with a tendon-driven compliant segmented spine whose effective stiffness can be reconfigured through progressive mechanical jamming. By selectively constraining body segments, OmniFish shifts deformation from whole-body undulation to posterior body bending and localized tail oscillation, enabling bioinspired Anguilliform, Subcarangiform, Carangiform, Thunniform, and Ostraciiform swimming using a single tendon-driven actuator. The design was guided by morphometric analysis and evaluated through caudal-fin thrust characterization, numerical body-drag simulations, kinematic analysis, and swimming performance experiments. Kinematic analysis confirmed the intended robot transition from distributed body undulation to localized tail oscillation. Swimming experiments demonstrated distinct mode-dependent performance, with the Ostraciiform configuration achieving the highest straight-line velocity of 8.14 cm/s and the lowest cost of transport of 2.42 at 1.5 tail beats/s. These proof-of-concept results show that a mechanically simple stiffness-reconfigurable architecture can generate distinct BCF swimming modes and provide a versatile strategy for developing multimodal soft robotic fish.

0.21

A Tendon-Driven Robotic Jellyfish with Constrained Soft Actuation and Depth Control via Reinforcement Learning

cs.RO ·2026-09-24 ·Jiarui Peng, Yutong Wu, Zelong Wang, Ping Deng, Xiaotian Zhang +3 more
similarity 0.66
Abstract · 8 pages, 8 figures. Corrected a typo in an author name in the arXiv metadata. No changes to the manuscript

Jellyfish-inspired robots offer a compliant and efficient approach to underwater locomotion, but achieving large deformation together with repeatable actuation and closed-loop control remains challenging. In this work, we present a tendon-driven robotic jellyfish with constrained soft actuation. Each actuator combines a flexible substrate with discrete constraints, enabling bending up to \(150^\circ\) with an approximately linear tendon displacement-bending relationship. Eight actuators driven by four servos allow the robot to perform stable swimming, attitude adjustment, and self-righting. Based on the linear actuation, a reinforcement-learning controller is further developed, enabling closed-loop depth regulation in both simulation and physical experiments. These results show that mechanical constraints can improve the controllability of soft actuation while preserving compliant jellyfish-like motion, providing a route toward manoeuvrable and autonomous jellyfish robots.

0.35

All You Need Is Low Fidelity: Zero-Shot Sim-to-Real of Learned Robotic Fish Control

cs.RO ·2026-09-29 ·Liam Maloney, Simon Ramchandani, Mike Y. Michelis, Ronan Hinchet, Robert K. Katzschmann
similarity 0.63
Abstract · 8 pages, 10 figures, submitted to ICRA 2027. Liam Maloney and Simon Ramchandani contributed equally

Complex tasks for underwater robots remain limited by the capabilities of their controllers. Learning a better one for a soft, underactuated robotic fish trades simulator cost against fidelity. We show that an intentionally low-fidelity simulator is enough: a stateless, quasi-steady fluid model with no wake and no added-mass history suffices to learn a \emph{general}, closed-loop controller that transfers to hardware without tuning. Our platform is a soft, single-motor, tendon-driven fish whose policy observes only what the hardware can measure. A staged pipeline grounds the simulator in two independent identifications, fixing the tail dynamics and a stateless fluid model; the policy then acts through a band-limited rhythmic trajectory generator rather than commanding the tail directly. Deployed unchanged in an outdoor pool, a single policy performs closed-loop target reaching, disturbance rejection, and out-of-distribution target acquisition and tracking. The transfer rests on the constraint rather than the fidelity: the generator cannot leave the band over which the fluid was identified. This raises the question of how much of the physics can reside in the controller rather than in the simulator.

0.25

Optimal control of a swimming robot based on Purcell's microswimmer model

cs.RO physics.flu-dynmath.OC ·2026-08-18 ·Noam Berkovich Lahav, Oren Wiezel, Yizhar Or
similarity 0.63
Abstract

Purcell's swimmer is a well-known planar model of a swimming microorganism, governed by low Reynolds number hydrodynamics, which is comprised of three rigid links connected by actuated rotary joints. This model has been analyzed as a robotic locomotion system governed by first-order nonlinear dynamics with a periodic input (gait) of the two joint angles. In this work, we present a robotic macro-scale realization of this three-link swimmer moving in a highly viscous fluid. We propose a simple variant of Purcell's theoretical model with non-slender links and a central rigid sphere which represents the added drag of the robot's central flotation block, and calibrate the model's parameters to fit experimental measurements. Next, we apply optimal control formulation based on Pontryagin's Maximum Principle (PMP) in order to find optimal gaits that maximize the displacement per cycle under bounds on the joint angles. Employing a differential geometric method that transforms the problem to area integral enclosed by the gait trajectory in the plane of joint angles, enables visual interpretation which explains topological changes in displacement-optimal gaits upon varying the bound on the joint angles. We then apply PMP formulation to the problem of maximizing Lighthill's energy efficiency in order to obtain a boundary value problem (BVP) whose solution gives efficiency-optimal gaits for Purcell's swimmer model, as well as its variant with a central sphere. Finally, we utilize numerical methods such as parameterizing the input gait as a truncated Fourier series, as well as GPOPS-II solver, to produce sufficient initial guess values for solving the BVPs and obtaining efficiency-optimal gaits.

0.16

Multifunctional Locomotion Control of Multi-Jointed BURs with Swimming and gait Capabilities

cs.RO ·2026-09-29 ·Takumi Asada, Hideo Furuhashi, Kenta Tabata, Renato Miyagusuku, Koichi Ozaki
publishedcode/data similarity 0.61
Abstract · Preprint version of an article published in Advanced Robotics (2026)

Multimodal biomimetic underwater robots (BURs) can conduct underwater tasks suitable for the environment. Combining the characteristics of aquatic organisms enables the swimming and leggedlocomotion required for underwater exploration. Locomotion control mechanism relies on rule-based behavior selection and the designer's discretion. This limits the robot's ability to acquire new behavioral capabilities to the predetermined range of behaviors. To address these challenges, we propose a mechanism and control system that enables the expression of multimodal locomotion capabilities from the same multi-jointed structure. A mechanism equipped with four leg-fins each having four axes is used. This controller achieves nonlinear behavior based on sensor modalities, rather than relying on predefined conditional rule-based on locomotion functions. This system was validated through both physical and simulation testing based on multiple sensor data and behavioral patterns. Utilizing a potential function in multimodal locomotion control was verified to enable transitions between two or three behaviors. Implementing the control method as a multimodal controller is expected to enhance its application in underwater exploration. Our project page is at https://tasada038.github.io/multi-jointed-bur/.

0.41

Adaptive Bendpoint Formation in Octopus-Inspired Soft Continuum Arms

cs.RO ·2026-10-18 ·Jessica Gumowski, Julian Finn, Krishna Manaswi Digumarti, David Howard
similarity 0.60
Abstract

Octopuses exhibit a powerful form of embodied intelligence from a highly adaptable soft body. One key mechanism is the ability to instantiate bending points at any location along the arm, which enables performant and dexterous behaviours. Taking inspiration from the octopus for its dexterity, this study focuses on changing the curvature of a tendon-actuated arm by adaptively changing the anchoring end-point along the arm. An array of inflatable shells is integrated into the arm, where inflating a shell causes an increase in friction at the location, jamming the tendon and creating a temporary new anchoring point. The novel soft actuator does not break the continuity of the arm between the actuated segment and the loose segment. Experiments show that the actuated segment has a non-constant bell-shaped curvature which is comparable to that of a real octopus arm during a reaching motion. Compared to conventional single-tendon continuum manipulators, the proposed design offers an expanded workspace and enhanced dexterity through the ability to independently shape different regions of the arm through selective curvature tuning. At the same time, it avoids the mechanical complexity typically associated with multi-segment, multi-actuator systems.

0.14

PneuGen: Task-Driven Agentic Co-Design of Soft Pneumatic Robots

cs.RO ·2026-11-09 ·Shaohong Zhong, Marco Pontin, Perla Maiolino
similarity 0.58
Abstract

Task-driven design of soft robots requires the consideration of factors such as geometry, morphology, material properties, and actuation, resulting in a large and complex design space that is challenging to explore. Computational optimisation methods leverage signals from simulation to iteratively improve designs to achieve task objectives. However, these methods typically demand high computational load for both optimisation and simulation. We present PneuGen, an agentic co-design framework for soft robots that leverages Large Language Model (LLM) agents to search over the soft robot design space efficiently. A designer agent proposes design programs from a parametric component library, and a separate critic agent analyses simulation diagnostics and recommends targeted revisions. Fitted module response models provide reusable physical priors relating geometry and pressure to deformation. Design programs are automatically validated and converted into finite-element simulations, enabling iterative evaluation. Across grasping tasks on primitive shapes and challenging objects, as well as shape-matching tasks that require multi-directional planar and 3D deformation, the proposed framework significantly outperforms prior computational optimisation baselines. Ablation experiments also highlight the utility of the critic agent and the module response model in facilitating efficient design. We additionally demonstrate the agent-generated soft robot designs in real-world shape-matching and grasping tasks.

0.12