CS Paper Radar

An Experimental Study of Downwash Effects on a Continuum Manipulator Integrated with a Multirotor UAV

Anuraj Uthayasooriyan, Krishna Manaswi Digumarti, ernando Vanegas, Felipe Gonzalez

cs.RO ·submitted 2026-08-19 03:54 UTC · v1
top venue

Abstract

Continuum arm aerial manipulation systems leverage soft-manipulator compliance and dexterity for tasks in confined or hazardous environments, but propeller downwash can degrade performance, particularly near walls and the ground. This effect remains uncharacterized for continuum manipulators. This letter experimentally studies downwash-induced kinematic deviations of a tendon-driven continuum manipulator integrated with a multirotor platform. Under still-air conditions, the CM is compared with a constant-curvature (CC) model. Downwash- induced end-effector pose deviations are then quantified relative to the mean still-air experimental baseline at four propeller throttle levels in free space, and at maximum throttle near a wall, and near the ground. Vertical position and yaw show the largest deviations and are amplified by ground effect. A CC-guided Gaussian process regression (GPR) residual model is learned from experimental data that improves forward pose prediction RMSE (position by 89-95%, orientation by 47-79%), and support compensation-oriented, downwash-aware modeling of continuum arm aerial manipulation systems.

Comment
Accepted to publish in Robotics and Automation Letters
Journal ref
IEEE Robotics and Automation Letters, vol. 11, no. 9, pp. 10704-10711, Sept. 2026
DOI
10.1109/LRA.2026.3709580

Closest papers

Nearest neighbours by meaning across the whole index.

An Open MuJoCo Simulation Framework for a Quadrotor Carrying a Tendon-Driven Soft Continuum Arm

cs.RO eess.SY ·2026-10-11 ·Haitham El-Hussieny
code/data similarity 0.62
Abstract

Combining aerial robots with soft continuum manipulators promises safe, compliant interaction with the environment, but the coupled dynamics of a free-flying base and a highly deformable, underactuated arm are difficult to study without a suitable simulator. This paper describes an open-source simulation framework, built on the MuJoCo physics engine, for a quadrotor that carries a tendon-driven soft continuum arm underneath its body. The arm is modelled as a pseudo-rigid-body chain of twelve segments joined by pairs of orthogonal compliant hinges. Three tendons, spaced \SI{120}{\degree} apart and routed through every segment, bend it in any direction. A geometric tracking controller on $SE(3)$ flies the vehicle; its rotor allocation matrix is generated directly from the model description. A closed-form tendon-tension allocation keeps every tension within its limits and gives the same bending moment in every direction. We report the full set of modelling choices and parameters, and we evaluate the framework in four simulated scenarios: a \SI{36}{\second} mission with a figure-eight and a tendon-driven tip sweep, an attitude-gain study, a quasi-static characterization of the bending workspace, and an impulsive disturbance applied to the arm tip. With the nominal gains the vehicle tracks the mission with \SI{3.1}{\centi\meter} RMS position error while the arm tip swings up to \SI{37}{\centi\meter} from the body axis. The gain study shows that a low-bandwidth attitude loop lets the arm excite sustained oscillations. The simulation runs about $15\times$ faster than real time on a laptop CPU. All models, controllers and scripts that reproduce the figures are released.

0.25

Temporal Learning for End-Effector Position Estimation under Aerodynamic Disturbances in Aerial Continuum Manipulation

cs.RO cs.AIcs.LG ·2026-09-23 ·Niloufar Amiri, Houman Masnavi, Farrokh Janabi-Sharifi
similarity 0.58
Abstract

This paper investigates temporal neural networks for \mbox{end-effector} position \mbox{estimation} of an aerial continuum manipulator (ACM) operating under aerodynamic effects induced by the unmanned aerial vehicle (UAV). An experimental dataset is collected under stationary (\mbox{rotor-off}) and \mbox{free-hovering} conditions across continuum robot (CR) configurations and UAV altitudes, providing \mbox{end-effector} position measurements with and without aerodynamic residuals. To establish a nominal framework, \mbox{strain-parameterized} kinematic models with progressively richer strain bases are evaluated to balance model complexity and prediction accuracy. The selected nominal model then serves as the baseline for 3D position residual estimation using a \mbox{closed-form} \mbox{continuous-time} (CfC) neural network, with a multilayer perceptron (MLP) and a gated recurrent unit (GRU) used for comparison. On unseen test experiments, the CfC achieves an RMSE of \(22.00\pm1.70~\mathrm{mm}\) over five random seeds, compared with \(36.38\pm3.58~\mathrm{mm}\) for the MLP and \(27.72\pm2.92~\mathrm{mm}\) for the GRU, corresponding to reductions of \(39.52\%\) and \(20.62\%\), respectively. These results demonstrate the effectiveness of \mbox{continuous-time} learning for \mbox{end-effector} position estimation under aerodynamic disturbances relative to static and \mbox{discrete-time} learning methods.

0.24

Drone Soccer: Learning to Manipulate with Multicopter Downwash

cs.RO ·2026-09-29 ·Neelay Joglekar, Bavin Saravanan, Yutong Wang, Varun Kandiyappan, Junyi Geng +1 more
published similarity 0.58
Abstract · 5 pages, 3 figures, IROS 2026 Workshop (Sim2Real and Classical Control)

Although multicopter drones are traditionally designed for "perception-only" tasks, like mapping and exploration, recent work has sought to develop Unmanned Aerial Manipulators (UAMs) to solve mobile manipulation tasks. Aerial manipulation performance can be impacted by "downwash," the airflow produced by propellers, but current state-of-the-art UAMs either ignore downwash or treat it as a disturbance. Instead, is it possible to actively use downwash as a tool during manipulation? We design a drone soccer task to explore the feasibility of downwash-based manipulation. Specifically, we develop a simplified downwash dynamics model which we use to train an RL policy to dribble a soccer ball. We further demonstrate that our policy transfers to real world deployment. This work provides key insights into novel manipulation capabilities for multicopters.

0.32

AeRSoM: An Aerial Rigid-Soft Integrated Manipulator for Contact-Rich Manipulation

cs.RO ·2026-09-22 ·Jiacheng Liang, Hang Zhong, Yaonan Wang, Ge Chen, Zhixing Zhang +3 more
similarity 0.58
Abstract

Contact-rich aerial manipulation remains fundamentally challenging because interaction forces are directly transmitted to the aerial platform, often leading to instability and degraded task performance. While compliant manipulators can mitigate these effects, existing aerial manipulation systems typically struggle to reconcile interaction compliance with manipulation precision. To this end, this article presents an aerial rigid-soft integrated manipulator (AeRSoM) robot that realizes embodied compliance for aerial manipulation. The proposed system integrates a fully actuated aerial platform, a rigid-soft manipulator, and variable-stiffness regulation to simultaneously achieve stable flight, compliant interaction, and precise manipulation. By distributing compliance throughout the manipulation system, the proposed design leverages distributed embodied compliance to passively absorb contact disturbances while preserving sufficient stiffness for task execution. To fully exploit the mechanical design, a composite control framework is developed for precise end-effector trajectory tracking in the presence of uncertainties and external disturbances. Extensive real-world experiments are conducted in representative contact-rich aerial manipulation tasks, including dynamic transmission-line grasping, physical interaction with a wind turbine blade, peg-in-hole, and screwing operations. The results demonstrate that the proposed rigid-soft integration significantly improves interaction robustness and task adaptability while maintaining manipulation accuracy, highlighting that embodied compliance provides a promising design paradigm for enhancing the safety, robustness, and versatility of aerial manipulation.

0.20

Robotic Boomerang Throwing via Model-Based Release Design

cs.RO ·2026-10-07 ·Yang Liu, Colin Jones, Aude Billard
code/data similarity 0.58
Abstract · Project page: https://robot-boomerang.github.io

Throwing objects that generate aerodynamic lift can greatly extend robot throwing beyond ballistic flight. A returning boomerang is a challenging example because its flight depends strongly on the release velocity, attitude, and spin, while robotic manipulators cannot readily reproduce the rapid motions used in human throwing. We present a model-based framework for robotic boomerang throwing centered on the release state. We identify the boomerang flight dynamics in stages to predict how flight changes across design variations. To systematically design the robot throwing motion, we screen candidate parameters according to how strongly and consistently they control release spin under uncertain contact conditions. These models are then used to design the throwing motion and boomerang for a 6-DoF manipulator with limited joint speeds. To our knowledge, this is the first robotic manipulator to generate a returning boomerang flight. In the demonstrated returning trial, the boomerang is released at 51 rad/s (8.1 rev/s), reaches 2.03 m from the robot base, and returns to touch down 0.31 m from the base. The successful release differs significantly from the measured human throws, showing that a robot need not imitate human throwing motion to achieve a returning flight. The project page is available at https://robot-boomerang.github.io

0.23

A Morphing Aerial Robot With Thruster-Integrated Flexible Continuum Links for Shape Adaptive Aerial Manipulation

cs.RO ·2026-09-16 ·Eri Sawada, Kazuki Sugihara, Ayano Miyamichi, Kunio Kojima, Kei Okada
published similarity 0.57
Abstract · Accepted to 2026 IEEE/RSJ International Conference on Intelligent Robots and Systems (IROS)

In recent years, aerial manipulation has attracted increasing attention as a key to expand the application of aerial robots. In this work, we focus on two major research directions for achieving versatile aerial manipulation: (i) acquiring high environmental adaptability using soft manipulators, and (ii) expanding the feasible wrench space by distributing thrusters along the manipulator. However, no aerial robot has simultaneously satisfied these two requirements. Therefore, in this paper, we propose a morphing rotor-distributed aerial robot with flexible continuum links that achieves both high shape adaptability and an expanded wrench space. The flexible continuum links function as soft manipulators, passively conforming to the shape of the environment, while the thrusters distributed along the continuum links expand the feasible thrust wrench space and enable the end-effector to exert large interaction forces. To realize the proposed robot, it is essential to suppress vibrations of the lightweight continuum links. Thus, we develop a composite leaf-spring structure that provides both high torsional and vertical stiffness, and vibration-suppressing control methods. Using these implementations, we demonstrate stable flight and a variety of aerial manipulation tasks. To the best of our knowledge, this is the first work to realize aerial manipulations using flexible links with an integrated thruster.

0.29

Effector-Centric NMPC of Tiltable-Multirotors for Offset-Free Omnidirectional Aerial Manipulation

cs.RO ·2026-08-18 ·Jinjie Li, Yicheng Chen, Johannes Kübel, Haokun Liu, Junichiro Sugihara +1 more
top venue similarity 0.56
Abstract · 22 pages, 26 figures. Accepted to IEEE Transactions on Robotics (T-RO). This arXiv version includes a two-page appendix with additional impl…

Aerial manipulation extends robotic operations to previously inaccessible aerial environments. Unlike arm-equipped aerial systems, tiltable-multirotors can directly generate six-degree-of-freedom wrenches through their flight bases, enabling both efficient movement and omnidirectional operation by tilting the thrust direction. This work presents a design analysis and a wrench-based control framework for tiltable-multirotors in aerial manipulation. We show that a four-rotor tiltable configuration provides a balance between interference-free propeller sizing and hovering efficiency across different attitudes, and its null-space redundancy is crucial for traversing singular configurations under physical constraints. We further show that an upward end-effector placement yields a favorable trade-off between geometric clearance and available wrench. To address disturbances, we propose a dual strategy consisting of a modified integral term for model error and an acceleration-based estimator for external wrenches. Building on these insights, we develop an effector-centric nonlinear model predictive control (NMPC) framework that integrates design choices, singularity handling, and disturbance compensation into a unified formulation. The proposed framework runs fully onboard at 100 Hz on a custom-built tiltable-quadrotor. Real-world experiments, including a 90-deg step cartwheel rotation, whiteboard pushing, and continuous 360-deg valve turning, demonstrate the feasibility of wrench-based omnidirectional manipulation with singularity traversal on a one-DoF-per-arm tiltable-quadrotor.

0.50

Design and Characterization of a Unified Continuum Robot Actuation Platform

cs.RO ·2026-10-14 ·Yunti Xu, Aedan Mangan, Miheer Potdar, Alex Lu, Tania K. Morimoto
similarity 0.56
Abstract

Continuum robots enable dexterous access to confined spaces in applications such as minimally invasive surgery and industrial inspection. However, their actuation systems are often custom-designed for specific robot architectures and tasks, limiting reuse across publications, institutions, and applications. This paper presents a unified actuation platform that decouples actuation hardware and software from continuum robot design. The platform provides modular actuation across continuum robot classes, scales to a large number of degrees of freedom (DOFs), and integrates with conventional serial manipulators for hybrid architectures. We validate the platform on an open-sourced surgical robotic system and experimentally characterize the actuation modules, achieving sub-millimeter translational accuracy and less than $5^\circ$ rotational error over ranges of $30$~mm and $180^\circ$, respectively. We further demonstrate the platform in two surgical use cases: teleoperation of a continuum camera in a constrained environment and bimanual manipulation using $2.53$~mm concentric-tube-robot-based forceps alongside a conventional wristed instrument. All hardware designs and ROS-based software are open-sourced to facilitate reuse and further research in continuum and surgical robotics.

0.31