CS Paper Radar

Pneumatic Units for Logic-based Sequential Excitation (PULSE) in Wearable Haptic Devices

Jessica Healey, Anoush Sepehri, Michael T. Tolley, Tania K. Morimoto

cs.HC cs.RO ·submitted 2026-08-20 23:53 UTC · v1

Abstract

Soft, wearable robotic devices can deliver haptic feedback to support a wide range of tasks, such as extended reality, training various skills, and rehabilitation. Pneumatic actuation can deliver complex haptic feedback, is lightweight and compliant, and can be incorporated into textiles, making it promising for wearable applications. These soft pneumatic devices, however, typically require a valve and input for each pneumatic actuator, making it challenging to develop fully portable devices for at-home use. In this work we present a pneumatic unit for logic-based sequential excitation (PULSE). The PULSE is a flat, textile-based pneumatic actuator with embedded fluidic logic. By combining these actuators into a fluidic ring oscillator, we decreased the typical amount of required pneumatic inputs for a haptic forearm sleeve by 60%, with the ability to scale. We built the ring oscillator by optimizing design variables to reach desired periods of oscillation. We demonstrated a set of tactile stroking cues with periods ranging from 1.16 to 1.56 s and forces ranging from 1.07 to 2.04 N. We assessed the sleeve's ability to render differentiable, pleasant, and continuous haptic cues in a user study. The forearm sleeve containing PULSEs successfully delivered four directional cues and guided users to target wrist angles with fast reaction times, low overshoot amounts, and a 93.3% average accuracy of correct initial directions.

Comment
9 pages, 6 figures

Closest papers

Nearest neighbours by meaning across the whole index.

A Wearable Pneumatic Device for Continuous, Closed-Loop, Bidirectional Tactile Interaction

cs.RO ·2026-09-01 ·Cosima du Pasquier, Aliyah Smith, Serin Huber, Joshua Phelps, Ilana A. Cohen +3 more
similarity 0.66
Abstract

We present a system of two wearable pneumatic haptic devices that supports continuous, closed-loop, bidirectional tactile interaction at perceptually relevant force and temporal scales. A single device can contain up to twelve pressure sensing channels connected to textile-based pneumatic pouches. Each channel in a device can be used as a sensor, an actuator, or both. As an actuator with integrated sensing, the channel generates stable skin indentation through local closed-loop control. As a sensor, a channel can be mounted (or worn) on any surface, including on a robot gripper or on the human body, and used to measure touch interactions with the environment or a human user. A distributed architecture supports sustained pressure output, rapid dynamic response, and wireless pairing of identical devices in a system to transmit and reproduce tactile pressure signals in real time. Device-level characterization demonstrates force bandwidth exceeding 30 Hz, rapid and well-damped step responses, and extended pressure retention compared to prior compact pneumatic platforms. Human studies show that pressure-based fingertip feedback enables discrimination of force and stiffness, improves teleoperated manipulation by reducing applied pressures by up to 23.1% and task duration by up to 27.4%, and lowers subjective mental workload by 18.8%, particularly under visually constrained conditions. By unifying tactile sensing and haptic feedback within a single pneumatic modality, the device provides a practical foundation for bidirectional touch interaction in teleoperation.

0.14

A Reconfigurable Fabric Based Pneumatic Actuator with Button Fastened Constraint Modules for Multi Mode Actuation

cs.RO ·2026-10-08 ·Kentaro Kimura, Hiroki Ishizuka, Yusuke Sakaue, Sei Ikeda, Osamu Oshiro
similarity 0.66
Abstract · IEEE Access in Revision

Soft pneumatic actuators are widely used in soft robotics. However, their actuation modes are typically fixed by internal chamber designs or reinforcements, making post fabrication reconfiguration difficult. This paper presents a reconfigurable fabric-based pneumatic actuator that enables rapid, tool free, and reusable switching among multiple actuation modes by attaching constraint fabric modules to a buttoned textile sleeve. By rearranging low-stretch constraint parts on a single actuator body, the proposed system realizes four actuation modes isotropic expansion, contraction, bending, and twisting without redesigning or disassembling the actuator.We further introduce an attachable capacitive fabric-based tactile sensor module that can be mounted at arbitrary locations on the actuator surface for task dependent contact sensing. Experiments demonstrated an elongation ratio of 1.2, a maximum bending angle of approximately 60 degrees, and a twisting angle of approximately 90 degrees at 24 kPa, while achieving blocking forces exceeding 10 N across all modes. The tactile sensor exhibited a monotonic, force-dependent increase in capacitance with low hysteresis (approximately 12%) and stable cyclic responses under preload. Finally, we constructed soft robotic arms composed of multiple actuators and demonstrated in situ motion reconfiguration for grasping by changing the attached constraint patterns. These results indicate that the proposed modular constraint and sensing framework improves the functional adaptability of fabric-based soft robots while preserving a simple, robust actuator structure.

0.23

Hugging Suit: Pneumatically-Actuated System Design for Remote Haptic Experiences

cs.HC cs.ET ·2026-10-06 ·Russian, Wu, Luke Hespanhol, Marius Hoggenmueller, Hannes Waldschütz +1 more
published similarity 0.62
Abstract · Accepted Work in Progress at the IEEE World Haptics Conference 2025, July 8-11, 2025, Suwon, South Korea. 2 pages, 1 figure

The COVID-19 pandemic emphasised the importance of remote emotional communication and highlighted a gap in existing technologies that lack haptic channels. While video calls maintain visual and auditory presence, they cannot convey the emotional depth of physical contact, especially hugging, a universally recognised form of intimacy and support. To explore this challenge, we developed the Hugging Suit, a pneumatically-actuated wearable system that enables users to simulate and receive remote hugs in real time. Unlike prior haptic systems that focus solely on tactile sensation, our approach integrates both technical and experiential considerations. The system integrates a programmable Air Actuator Matrix (AAM), a portable high-pressure pneumatic unit, and a fabric-based pressure sensor layer, enabling precise, wearable haptic feedback while remaining lightweight and mobile. Guided by a Research through Design (RtD) methodology, we iteratively refined the prototype to improve tactile resolution, overall usability, and user comfort, while introducing modular components to support flexible and scalable haptic configurations. In parallel, we explored how specific contextual factors, such as lighting, privacy, and the visibility of the remote partner, might shape the emotional and perceptual experience of receiving a remote hug. Preliminary feedback suggests that low-lit, private spaces, especially when users could also see their remote partner via video, improved emotional engagement and comfort during mediated haptic experiences. Our low-cost, maker-space-friendly approach contributes to affective haptics applications in long-distance relationships, emotional regulation, and remote therapeutic support.

0.29

Pneumatic neurons for soft robots enable inflate-and-fire networks for rhythmic motion

cs.RO ·2026-09-10 ·Dongting Li, Michael Tolley, Nick Gravish
similarity 0.61
Abstract

Animals coordinate their movements through distributed neural circuits, but soft robots still typically depend on external, centralized electronics for control. Building soft robots that operate without centralized electronic controllers while remaining responsive to their environment remains a frontier challenge in soft robotics. In this work we introduce a soft-robot control architecture inspired by leaky integrate-and-fire models of biological neural circuits. The Pneumatic neuron (Pneu-ron) is a soft actuator that unifies energy conversion, logic, and actuation in one component. Each module combines a low-boiling-point fluid (LBF), a heater, and a mechanical switch into a self-excitable unit. Boiling the LBF inflates the module and triggers excitation and inhibition of adjacent modules in a process we call "inflate-and-fire". When interconnected into excitatory-inhibitory rings, Pneu-rons generate stable, sequential oscillations whose frequency emerges from the material dynamics and environmental conditions. By harnessing the inflation of Pneu-rons for actuation these networks can drive oscillatory locomotion of soft robots. Pneu-ron networks sustain oscillation under mechanical load and thermal variations, adapting through material physics rather than computation. Dynamical modeling of these networks reveals a dimensionless bifurcation diagram that dictates the network's oscillatory behavior. Encoding logic and actuation into material-level modules presents a new avenue for adaptive, electronics controller-free, soft robots.

0.20

PneuTac: Tactile Manipulation with Soft Pneumatic Robots via Unified MPM-Gaussian Splatting Simulation

cs.RO ·2026-09-29 ·Shaohong Zhong, Marco Pontin, Joe Watson, Perla Maiolino, Ingmar Posner
similarity 0.59
Abstract

Soft robots and tactile sensors have demonstrated great potential in delicate manipulation tasks. Soft pneumatic robots enable safe contact through compliance, and vision-based tactile sensors offer high-resolution touch perception. However, learning tactile manipulation with compliant robots has been challenging, bottlenecked by the lack of efficient simulation. Existing simulators typically model them in isolation, and exhibit large calibration gaps that are difficult to overcome efficiently. We present PneuTac, a unified framework for tactile-feedback manipulation with soft pneumatic robots. We leverage the material point method (MPM) for modelling the dynamics of the soft robot and the deformable tactile membrane, and 3D Gaussian splatting (3DGS) for rendering. Real-to-sim modelling is done with a simple vision-based method, to then train action and perception networks for efficient simulation with surrogate models. We use the framework to drive a tactile-guided pipeline to collect demonstrations in simulation. Through experiments on a custom-designed pneumatic soft finger with a tactile sensing tip, together with additional cross-device evaluations, we show that PneuTac is capable of accurately modelling soft robots with tactile sensors, and that policies trained with simulation-augmented demonstrations outperform baselines trained on the same real data on three real-world contact-rich compliant manipulation tasks, making it a practical framework for tactile manipulation on compliant hardware.

0.36

Elbow Angle Guidance System Based on Surface Haptic Sensations Elicited by Lightweight Wearable Fabric Actuator

cs.HC cs.RO ·2026-08-11 ·Kenta Yokoe, Tadayoshi Aoyama, Yuki Funabora, Masaru Takeuchi, Yasuhisa Hasegawa
published similarity 0.59
Abstract · This is the accepted version of the paper published in Proc. 2024 IEEE International Conference on Advanced Intelligent Mechatronics (AIM), …

The demand for wearable haptic devices has rapidly increased for various applications. However, many haptic devices interfere with the wearer's activities and movements. In addition, several haptic devices fail to elicit intuitive haptic sensations by adjusting to the natural posture of the wearer. To address these issues, we propose an elbow angle guidance system using a lightweight wearable fabric actuator. The proposed actuator is made of fabric and has two McKibben-type artificial muscles attached to it, rendering it extremely lightweight and facilitating the delivery of surface haptic sensations to intuitively induce elbow extension and flexion. The surface haptic sensation elicited by the fabric actuator is adjusted to natural body movements without interfering with the wearer's movements. Moreover, the proposed system measures and guides the elbow angle by changing the intensity of the surface haptic sensation delivered to users in real time. The accuracy of the proposed system is demonstrated through experiments involving human participants.

0.65

A Task-Agnostic Control Strategy for Dynamic Assistance with Pneumatically Actuated Soft Exosuits

cs.RO cs.HC ·2026-08-18 ·Anoush Sepehri, Zachary Huang, Raymond de Callafon, Michael T. Tolley, Tania K. Morimoto
similarity 0.58
Abstract

Pneumatic artificial muscles have provided new opportunities to develop upper-extremity soft exosuits for reha- bilitation, augmentation, and assisted daily living. However, the complex dynamics and limited bandwidth of these actuators has made providing responsive assistance based on user intention a longstanding challenge. In this work, we present an inverse-plant control strategy for pneumatically actuated soft exosuits that only relies on kinematic sensing for task-agnostic and dynamic assistance during daily living. We model the human-robot system using a Hammerstein dynamic model, consisting of a Preisach hysteresis model and a linear time-invariant filter, to capture the static and dynamic behavior of the system. We personalize our model to each user using 140 s of data and approximate an inverse to integrate into our control loop. When evaluated on a test rig that emulated a soft assistive exosuit for the wrist, our controller reduced the interaction torque by up to 73% and the activation of key flexor and extensor muscles by up to 47% relative to the condition with no assistance for speeds ranging from 8°/s to 120°/s. Overall, this work presents a control strategy that can provide task-agnostic, dynamic assistance with pneumatically actuated soft exosuits without the need for physiological or force sensors to interpret user intention.

0.19

Intuitive Directional Sense Presentation to the Torso Using McKibben-Based Surface Haptic Sensation in Immersive Space

cs.HC cs.RO ·2026-08-10 ·Kenta Yokoe, Tadayoshi Aoyama, Yuki Funabora, Masaru Takeuchi, Yasuhisa Hasegawa
top venue similarity 0.57
Abstract · This is the accepted version of an article published in IEEE Transactions on Haptics 18(1), 244-254 (2025). DOI: 10.1109/TOH.2024.3522897. O…

In recent years, systems that utilize immersive space have been developed in various fields. Immersive spaces often contain considerable amounts of visual information; therefore, users often fail to obtain their desired information. Therefore, various methods have been developed to guide users toward haptic sensations. However, many of these methods have limitations in terms of the intuitive perception of haptic sensation and require practice for familiarization with haptic sensation. Fabric actuators are wearable haptic devices that combine fabric and McKibben artificial muscles to provide wearers with surface haptic sensation. These sensations can be provided to a wide area of the body with intuitive perception, instead of only to a part of the body. This paper presents a novel air pressure adjustment method for whole-body motion guidance using surface haptic sensations provided by a wearable fabric actuator. The proposed system can provide users with a directional sense without visual information in an immersive space. The effectiveness of the proposed system was evaluated through subject experiments and statistical data analysis. Finally, a directional sense presentation was conducted for users performing micromanipulations in a mixed-reality space to demonstrate the applicability of the proposed system for teleoperation.

0.73